• Journal of the Korean Ceramic Society
• /
• v.32 no.9
• /
• pp.967-976
• /
• 1995

The possiblity of the existence of a spontaneous relaxor-normal ferroelectric transition was proposed and examined using 1~5 mol% PbZrO3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 (PNN-PT) systems having tetragonal symmetry at rom temperature. On cooling, the system with 60mol% Pb(Ni1/3Nb2/3)O3 underwent a spontaneous transition from a relaxor to a normal ferroelectric state. A microscopic examination demonstrates that the relaxornormal ferroelectric transition corresponds to a micro-macro domain switching accompanied with thermoelastic martensitic transformation. The long-range macrodomains below the transition temperature were characterized by twinlike 90$^{\circ}$macrodomains with tetragonal symmetry. The relaxor-normal ferroelectric transition was further correlated with the rhombohedral-tetragonal first-order structural transition.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3213-3217
• /
• 2012

Reactive adsorption desulfurization (RADS) experiments were conducted over a series of commercial metal oxide supports ($Al_2O_{3-}$, $SiO_{2-}$, $TiO_{2-}$ and $ZrO_{2-}$) supported Ni/ZnO adsorbents. The adsorbents were characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), and Fourier transform infrared spectroscopy (FTIR) in order to find out the influence of specific types of surface chemistry and structural characteristics on the sulfur adsorptive capacity. The desulfurization performance of all the studied adsorbents decreased in the following order: Ni/ZnO-$TiO_2$ > Ni/ZnO-$ZrO_2$ > Ni/ZnO-$SiO_2$ > Ni/ZnO-$Al_2O_3$. Ni/ZnO-$TiO_2$ shows the best performance and the three hour sulfur capacity can achieve 12.34 mg S/g adsorbent with a WHSV of $4h^{-1}$. Various characterization techniques suggest that weak interaction between active component and support component, high dispersion of NiO and ZnO, high reducibility and large total Lewis acidity of the adsorbents are important factors in achieving better RADS performance.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1195-1199
• /
• 2003

In this study, in order to develop the low temperature sintering ceramics for multilayer piezoelectric transformer, dielectric and piezoelectric properties of PSN-PZT[0.91Pb(Sb$\sub$1/2/Nb$\sub$1/2/)$\sub$0.03/(Zr$\sub$0.495/Ti$\sub$0.505/)$\sub$0.97/O$_3$-0.04Pb(Ni$\sub$1/2/W$\sub$1/2/)O$_3$+0.05BiFeO$_3$+0.3wt％MnO$_2$+0.6wt％CuO〕 ceramics were investigated according to Zr/Ti ratio. As Zr/Ti ratio is increased, electromechanical coupling factor(k$\sub$p/) and dielectric constant increased and then decreased after the ratio of Zr/Ti=50/50. Also, mechanical qualify factor(Q$\sub$m/) decreased and then increased after the ratio of Zr/Ti=50/50.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.2
• /
• pp.89-97
• /
• 2010

$Al_2O_3$, $TiO_2$, $ZrO_2$, $Al_2O_3-TiO_2$, $Al_2O_3-ZrO_2$, 및 $TiO_2-ZrO_2$ 혼합 산화물을 지지체로 한 Ni 기반 혼합 산화물을 졸-겔법으로 제조하였다. 제조된 혼합 산화물은 1173K에서 열처리 한 후 구조적 특성 변화를 전자현미경 및 X-선 회절 분석을 이용하여 관찰하였으며, 수소를 이용한 승온 환원(TPR; temperature-programmed reduction) 실험을 통하여 1173K 까지 각 시료들의 환원 피크를 비교 고찰하였다. $Al_2O_3$ 또는 $TiO_2$ 가 혼합된 시료의 경우 1173K 에서의 열처리 후 니켈 알루미네이트 또는 니켈 티타네이트와 같은 새로운 결정상의 생성이 관찰되었으나 $ZrO_2$가 혼합된 경우에는 새로운 결정상의 생성이 관찰되지 않았다. TPR 결과에 의하면, $Al_2O_3$ 또는 $TiO_2$를 혼합된 시료의 경우 벌크 NiO의 TPR 결과와는 달리 생성된 새로운 결정상에 기인한 여러 개의 환원 피크가 나타났으나 $ZrO_2$를 혼합한 경우 벌크 NiO와 비슷한 환원 피크를 보였다. TPR 결과를 기초로 Arrhenius plot 으로부터 각 혼합 산화물들의 수소 환원 활성화 에너지를 도출하였다. $ZrO_2$를 지지체로 사용하는 경우 다른 혼합 산화물들보다 지지체로서 안정한 혼합 산화물상을 형성한다는 것을 지시하듯이 상대적으로 가장 낮은 활성화 에너지를 나타냈다.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.51-52
• /
• 2006

[ $Ti_{45}Zr_{38}Ni_{17}$ ] powders were thermally sprayed onto mild steel substrates in air and under a reduced pressure of argon. Several oxides were formed after thermally-spraying the mechanically-alloyed powders in air. After spraying in a reduced pressure of argon, the coating layers obtained from the gently mixed powders consisted of the elemental metals, but an amorphous phase primarily appeared in the thermally-sprayed mechanically-alloyed powders, which transformed into the icosahedral quasicrystal phase and a minor $Ti_2Ni-type$ crystal phase after annealing at 828 K. The Vickers hardness and the contact angle with pure water for the quasicrystal layers were about 7 GPa and $92^{\circ}$ respectively.

• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.5
• /
• pp.367-372
• /
• 2013

Hydrogen storage as a metal hydride is the most promising alternative because of its relatively large hydrogen storage capacities near room temperature. TiMn2-based C14 Laves phases alloys are one of the promising hydrogen storage materials with easy activation, good hydriding-dehydriding kinetics, high hydrogen storage capacity and relatively low cost. In this work, multi-component, hyper-stoichiometric $Ti_{0.85}Zr_{0.13}(Fe_x-V)_{0.56}Mn_{1.47}Ni_{0.05}$ C14 Laves phase alloys were prepared by a vacuum induction melting for a hydrogen storage tank. Since pure vanadium (V) is quite expensive, the substitution of the V element in these alloys has been tried and some interesting results were achieved by replacing V by commercial ferrovanadium (FeV) raw material. In addition, the melt-spinning process, which was applied to the manufacturing of some of these alloys, could make the plateau slopes much flatter, which resulted in the increase of reversible hydrogen storage capacity. The improvement of sloping properties of melt-spun $Ti_{0.85}Zr_{0.13}(Fe_x-V)_{0.56}Mn_{1.47}Ni_{0.05}$ alloys was mainly attributed to the homogeneity of chemical composition.

• Journal of the Korean Ceramic Society
• /
• v.27 no.7
• /
• pp.934-942
• /
• 1990

The quarternary system ceramics 0.5[yPb(Zn1/3Nb2/3)O3-(1-y)Pb(Ni1/3Nb2/3)O3]-0.5[xPbTiO3-(1-x)PbZrO3](PZN-PNN-PT-PZ) was fabricated by the columbite precursor method to obtain a stabilized perovskite structure and by conventional method to evaluate the efficiency of the former methd. Dielectric and piezoelectric properties were investigated and the stability of the perovskite phase was studied as a function of PZN and PT contents and firing temperature. In the samples prepared by the columbite precursor method, the pyrochlore phase, which is detrimental to both the dielectric and piezoelectric properties, was not observed in the absence of PZN, and electric properties were improved even when fabricated at low temperature. By adding PZN, some pyrochlore phase appeared and the morphotropic phase boundary of the samples shifted to more Zr-rich composition. The temperature dependence of piezoelectric constant decreased with the addition of PZN, due to the rising of the Curie point.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.3
• /
• pp.245-251
• /
• 2000

Dielectric properties, piezoelectric properties and mechanical properties of NiO-doped Pb($(Ni_{1/3}Nb_{2/3})O_3-PbTiO_3-PbZrO_3$ ceramics were investigated. Powders, prepared by columbite precursor method, were cold pressed and sintered at temperature ranging from $1100^{\circ}C$ to $1250^{\circ}C$. Dielectric constant and piezoelectric constant increased with amount of NiO up to 1 mol% and then decreased with further addition of NiO. It seems that NiO acts as a sintering aid at the sintering temperatures of $1150^{\circ}C$. When the samples were sintered at temperature above $1200^{\circ}C$, however, both dielectric constant and electromechanical coupling factor decreased and mechanical quality coefficient increased with addition of NiO. Hardness and fracture toughness of PNN-PT-PZ increased with addition of NiO up to 1 mol%, and then decreased slightly with further addition of NiO. These results showed that dielectric properties, piezoelectric properties and mechanical properties of PNN-PT-PZ system seemed to be closely related with microstructural factors such as grain size, bulk density and the amount of second phase.

• Proceedings of the Korean Society of Laser Processing Conference
• /
• 2005.06a
• /
• pp.9-14
• /
• 2005

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.174.2-174
• /
• 2002