• Metals and materials international
• /
• 제24권6호
• /
• pp.1309-1314
• /
• 2018

In this study, we investigated the state of $Y_2O_3$, as a major additive element in Fe-based ODS alloys, during mechanical alloying (MA) processes by thermodynamic approaches and experimental verification. For this purpose, we introduced $Ti_2O_3$ that formed different reaction products depending on the state of $Y_2O_3$ into the Fe-based ODS alloys. In addition, the reaction products of $Ti_2O_3$, Y, and $Y_2O_3$ powders were predicted approximately based on their formation enthalpy. The experimental results relating to the formation of Y-based complex oxides revealed that $YTiO_3$ and $Y_2Ti_2O_7$ were formed when $Ti_2O_3$ reacted with Y; in contrast, only $Y_2Ti_2O_7$ was detected during the reaction between $Ti_2O_3$ and $Y_2O_3$. In the alloy of $Fe-Cr-Y_2O_3$ with $Ti_2O_3$, $YTiO_3$ (formed by the reaction of $Ti_2O_3$ with Y) was detected after the MA and heat treatment processes were complete, even though $Y_2O_3$ was present in the system. Using these results, it was proved that $Y_2O_3$ decomposed into monoatomic Y and O during the MA process.

• 한국재료학회지
• /
• 제9권2호
• /
• pp.217-225
• /
• 1999

The effect on the pitting corrosion resistance of laser welding and surface treatment developed as a repair method of stream generator tubing material that was a major component of primary system at nuclear power plant was observed. Some heat-treated Alloy 600 tubing materials used at domestic nuclear power plants were laser-surface observed. Some heat-treated Alloy 600 tubing materials used at domestic nuclear power plants were laser-surface melted and the microstructural characteristics were examined. The pitting corrosion resistance was examined through Ep(pitting potential) and degree of pit generation by means of the electrochemical tests and the immersion tests respectively. The pit formation characteristics were investigated through microstructural changes and the pit initiation site and pit morphology. The test results showed that the pitting corrosion resistances was increased in the order of the followings; sensitized Alloy 600, solution annealed alloy600, and laser surface melted Alloy 600. Pits were initiated preferably at Ti-containing inclusions and their surroundings in all tested specimens and it is believed that higher pitting resistance of laser-surface treated Alloy 600 was caused by fine, homogeneous distribution of non-soluble inclusions, the disappearance of grain boundary, and the formation of dense, stable oxide film. The major element of corrosion products filled in the pit was Cr. On the other hand, Fe was enriched in the deposit formed on the pit.

• 한국산학기술학회논문지
• /
• 제18권9호
• /
• pp.418-424
• /
• 2017

마그네슘은 다른 금속들에 비해 비강도가 높으며, 우수한 진동 흡수능, 전자파 차폐성 등으로 산업 전반에 많이 활용되고 있다. 예를 들면, 자동차 시트 프레임, 실린더 헤드 등 자동차 부품으로도 사용되며 노트북 케이스, 핸드폰 케이스 등의 전자제품에도 널리 사용되고 있다. 또한 신체의 뼈가 금이 가거나 부서졌을 경우, 그 손상된 뼈의 치료를 보조하기 위해 사용되는 골 접합용 임플란트 재료로 각광받고 있다. 현재 임플란트 재료로는 Ti alloy, Stainless steel, Co-Cr-Mo alloy등이 사용되어 지고, Mg 합금은 연구단계에 머물러 있다. 현재 골접합용 임플란트 재료의 문제점으로는 한번 접합 수술 후에 회복이 되면 이것을 제거하기 위한 수술을 또 해야 한다는 점이 있다. 하지만 마그네슘은 현재 재료와 비교하여 충분한 강도를 실현 할 수 있으며, 일정시간 후 자체적으로 분해되고 인체에 무해한 원소기 때문에 연구가 진행되고 있다. 그러나 순수 Mg으로는 충분한 강도와 내식성을 가질 수 없기 때문에 합금원소를 첨가하여 Mg 합금을 설계한다. 본 논문에서는 마그네슘에 인체에 무해한 Ca, Zn를 첨가하여 합금을 설계하였고, 추가적으로 강도와 내식성을 향상시키기 위해서 Grain refiner로서 Sr을 소량 첨가하여 최종 합금을 설계하였다. Sr은 방사선 원소는 인체에 유해하지만, 그 외 천연 Sr 원소는 인체에 무해하다. 이렇게 제조된 합금을 광학현미경, 주사전자현미경을 통해 미세조직분석을 수행하고, 인장시험, 동전위 분극 시험, 침지시험을 통해 기계적 특성 및 부식특성을 평가하였다. 결론적으로, Sr 첨가에 의해 조직이 미세해졌으며, 기계적 특성 및 내식성이 향성된 것을 확인 할 수 있었다.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2004년도 학술논문집
• /
• pp.285-291
• /
• 2004

LiCl-$Li_2O-O_2$ 용융염계에서 용융염 취급장치의 구조재료를 위한 평가의 일환으로 Inconel 718, X-750, Haynes 75, 263 합금의 부식거동을 분위기온도; $650^{\circ}C$, 부식시간: 24~168h, $Li_2O$농도; 3wt%, 혼합가스농도; Ar-10%$O_2$에서 조사하였다. LiCl-$Li_2O-O_2$ 용융염계에서 부식속도는 Haynes 263 ＜ Haynes 75 ＜ Inconel X-750 ＜ Inconel 718 순서로 나타났으며, Haynes 263 합금이 가장 우수한 내부식성을 나타내었다. Haynes 75의 부식생성물은 $Cr_2O_4$, $NiFe_2O_4$, $LiNiO_2$, $Li_2NiFe_2O_4$, Inconel 718의 부식생성물은 $Cr_2O_4$ 및 $NiFe_2O_4$ 이며 Haynes 263은 $Li(Ni,Co)O_2$, $NiCr_2O_4$ 및 $LiTiO_2$, Inconel X-750은 $Cr_2O_3$, $NiFe_2O_4$,$FeNi_3$, (Al,Nb,Ti)$O_2$의 부식생성물을 나타내었다. Haynes 263은 국부부식의 거동을 보이는 반면, Haynes 75, Inconel 718 및 Inconel X-750은 전면 부식 거동을 나타내었다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2009년도 추계학술대회 초록집
• /
• pp.105-106
• /
• 2009

AZ31 (3% Al, 1% Zn) Mg 판재의 내식성 향상을 위해 Ti/Zr/Polymer 복합계의 Cr-free 화성처리 방법을 이용하였다. 염수분무시험을 통해 최고 72시간 ($5{\sim}10%$ 발청) 내식성이 나타남을 확인하였다. 화성피막의 내식성은 그 피막이 가진 성분, 균일도, 치밀도, 형상 및 두께에 의해 좌우되는 만큼 TEM, SEM을 통해 화성피막 구조가 내식성과 어떠한 관련이 있는지 조사하였다. 또한, 화성처리 전 단계 공정인 탈지와 산세 및 중화 공정의 변수 조절을 통해 전처리 공정이 최종 화성피막의 물성에 어떠한 영향을 미치는지 조사하였다. 탈지조건을 $35{\sim}40^{\circ}C$, 5분에서 $50{\sim}80^{\circ}C$, $10{\sim}20$분으로 변경 시 좀 더 균일한 외관을 얻을 수 있었고, 적절한 중화제 선택을 통해 화성피막을 균일하게 형성시킬 수 있었다. 투과전자현미경 결과로 미루어 화성피막의 두께보다 균일도와 치밀도가 내식성에 결정적인 영향을 미치는 것을 확인할 수 있었다.

• 열처리공학회지
• /
• 제30권3호
• /
• pp.99-105
• /
• 2017

This study was carried out to investigate the effect of heat treatment on the microstructure and mechanical properties in 90% hot forged Incoloy 825 alloy. With increasing solution treatment temperature, the grain size increased and the volume fraction of total precipitates decreased, and the precipitates disappeared at $1,000^{\circ}C$. With increasing aging time at $700^{\circ}C$, the volume fraction of precipitate increased and the precipitates size increased. Most of the precipitates consist $Cr_{23}C_6$ carbide, and a small amount of TiC carbide was also observed. With decreasing solution treatment temperature and increasing aging time, tensile strength and hardness increased, and the elongation and impact value decreased. With increasing aging time, the impact value decreased sharply by the increased of the precipitate size.

• Transactions on Electrical and Electronic Materials
• /
• 제4권1호
• /
• pp.15-20
• /
• 2003

NiCr alloys are prepared onto poly-Si/ $SiO_2$/Si substrates to replace Pt bottom electrode with a new one for integration of high dielectric constant materials. Alloys deposited at Ni and Cr power of 40 and 40 W showed optimum properties in the composition of N $i_{1.6}$C $r_{1.0}$. The grain size of films increases with increasing deposition temperature. The films deposited at 50$0^{\circ}C$ showed a severe agglomeration due to homogeneous nucleation. The NiCr alloys from the rms roughness and resistivity data showed a thermal stability independent of increasing annealing temperature. The 80 nm thick BST films deposited onto N $i_{1.6}$C $r_{1.0}$/poly-Si showed a dielectric constant of 280 and a dissipation factor of about 5 % at 100 kHz. The leakage current density of as-deposited BST films was about 5$\times$10$^{-7}$ A/$\textrm{cm}^2$ at an applied voltage of 1 V. The NiCr alloys are possible to replace Pt bottom electrode with new one to integrate f3r high dielectric constant materials.terials.

• The Journal of Advanced Prosthodontics
• /
• 제12권2호
• /
• pp.100-106
• /
• 2020

PURPOSE. The purpose of this in vitro study was to evaluate the fitting accuracy of single crowns made from a novel presintered Co-Cr alloy prepared with a computer-aided design and computer-aided manufacturing (CAD/CAM) technique, as compared with crowns manufactured by other digital and the conventional casting technique. Additionally, the influence of oxide layer on the fitting accuracy of specimens was tested. MATERIALS AND METHODS. A total of 40 test specimens made from Co-Cr alloy were investigated according to the fitting accuracy using a replica technique. Four different methods processing different materials were used for the manufacture of the crown copings (milling of presintered (Ceramill Sintron-group_cer_sin) or rigid alloy (Tizian NEM-group_ti_nem), selective laser melting (Ceramill NPL-group_cer_npl), and casting (Girobond NB-group_gir_nb)). The specimens were adapted to a resin model and the outer surfaces were airborne-particle abraded with aluminum oxide. After the veneering process, the fitting accuracy (absolute marginal discrepancy and internal gap) was evaluated by the replica technique in 2 steps, before removing the oxide layer from the intaglio surface of the crowns, and after removing the layer with aluminum oxide airborne-particle abrasion. Statistical analysis was performed by multifactorial analysis of variance (ANOVA) (α=.05). RESULTS. Mean absolute marginal discrepancy ranged between 20 ㎛ (group_cer_npl for specimens of Ceramill NPL) and 43 ㎛ (group_cer_sin for crowns of Ceramill Sintron) with the oxide layer and between 19 ㎛ and 28 ㎛ without the oxide layer. The internal gap varied between 33 ㎛ (group_ti_nem for test samples of Tizian NEM) and 75 ㎛ (group_gir_nb for the base material Girobond NB) with the oxide layer and between 30 ㎛ and 76 ㎛ without the oxide layer. The absolute marginal discrepancy and the internal gap were significantly influenced by the fabrication method used (P<.05). CONCLUSION. Different manufacturing techniques had a significant influence on the fitting accuracy of single crowns made from Co-Cr alloys. However, all tested crowns showed a clinically acceptable absolute marginal discrepancy and internal gap with and without oxide layer and could be recommended under clinical considerations. Especially, the new system Ceramill Sintron showed acceptable values of fitting accuracy so it can be suggested in routine clinical work.

• 한국재료학회지
• /
• 제14권11호
• /
• pp.813-820
• /
• 2004

The electrolytic reduction of spent oxide fuel involves the liberation of oxygen in a molten LiCl electrolyte, which is a chemically aggressive environment that is very corrosive for typical structural materials. So, it is essential to choose the optimum material for the process equipment handling molten salt. In this study, corrosion behavior of Haynes 263, 75, and Inconel X-750, 718 in molten salt of $LiCl-Li_{2}O$ under oxidation atmosphere was investigated at $650^{\circ}C\;for\;72\sim360$ hours. At $3\;wt\%\;of\;Li_{2}O$, Haynes 263 alloy showed the highest corrosion resistance among the examined alloys, and up to $8\;wt\%\;of\;Li_{2}O$, Haynes 75 exhibited the highest corrosion resistance. Corrosion products were formed $Li(Ni,Co)O_2,\;LiNiO_2\;and\;LiTiO_2\;and\;Cr_{2}O_3$ on Haynes 263, $Cr_{2}O_3,\;NiFe_{2}O_4,\;LiNiO_2,\;Li_{2}NiFe_{2}O_4,\;Li_{2}Ni_{8}O_10$ and Ni on Haynes 75, $Cr_{2}O_3,\;(Al,Nb,Ti)O_2,\;NiFe_{2}O_4,\;and\;Li_{2}NiFe_{2}O_4$ on Inconel X-750 and $Cr_{2}O_3,\;NiFe_{2}O_4\;and\;CrNbO_4$ on Inconel 718, respectively. Haynes 263 showed local corrosion behavior and Haynes 75, Inconel X-750, 718 showed uniform corrosion behavior.

• 한국결정성장학회지
• /
• 제22권4호
• /
• pp.183-189
• /
• 2012

고온 열수송용 재료로 이용되는 Hastelloy X의 표면처리에 따른 고온물성 개선에 대한 연구를 수행하였다. Hastelloy X 기판 상에 각각 PVD법인 Arc discharge 및 Sputtering을 이용하여 TiAlN 및 $Al_2O_3$ 박막을 표면 코팅(overlay coating) 하였고, 분위기 분말을 이용하여 Al을 금속표면을 통해 확산시키는 방법인 Pack cementation법을 이용한 Al 확산코팅(diffusion coating: aluminiding)법을 이용한 표면처리를 수행하였다. 이들 표면처리가 Ni-Cr계 합금의 고온열처리에서 생성되는 두꺼운 불균질 산화물($Cr_2O_3$)형성 억제에 미치는 효과와 조성 및 표면미세구조가 물성에 미치는 영향에 대해 알아보기 위해, 표면처리 된 Hastelloy X 샘플들을 공기 및 헬륨가스 분위기에서 $1000^{\circ}C$로 열처리 하였으며, 열처리된 전후 시편들에 대해 상형성, 미세구조 및 고온 물성 변화를 측정하였다. 이러한 실험결과를 통하여 표면코팅법에 의한 TiAlN 및 $Al_2O_3$ 박막에 비해 Al 확산코팅한 경우 두꺼운 불균질 산화물($Cr_2O_3$)형성이 억제되어 보다 균질한 미세구조와 높은 내마모성 등 높은 고온 안정성을 보여주는 것을 확인할 수 있었다.