• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제26회 추계학술대회
• /
• pp.183-190
• /
• 1997

The wear behaviors of $Al_2O_3-40%TiO_2$ deposited on casting aluminum alloy(ASTM A356) by plasma spray against SiC ball have been investigated experimentally. Friction and wear tests are carried out at room temperature. The friction coefficient of $Al_2O_3-40%TiO_2$ coating is lower than that of pure $Al_2O_3$ coating(APS). It is found that low friction correspond to low wear and high friction to high wear in the experimental result. The thickness of $Al_2O_3-40%TiO_2$ coatings indicated the existence of the optimal coating thickness. It is found that a voids and porosities of coating surface result in the crack generated. As the tensile stresses in coating increased with the increased friction coefficient. The columnar grain of coating will be fractured to achieve the critical stress. It is found that the cohesive of splats and the porosity of surface play a role in wear characteristics. It is suggested that the mismatch of thermal expansion of substrate and coating play an important role in wear performance. Tensile and compressire under thermo-mechanical stress may be occurred by the mismatch between thermal expansion of substrate and coating. This crack propagation above interface is observed in SEM.

• 한국기계가공학회지
• /
• 제7권1호
• /
• pp.67-74
• /
• 2008

In this paper, the surface characteristics of the AIP-TiN coated of the SKH51 and SKD11 steels under various deposition times are presented with emphasis on the comparison of the two materials. The micro-particle, the surface roughness, the micro-hardness, the coated layer thickness, the atomic distribution of Ti, N and Fe elements and the adhesion are measured for various deposition times. It has been shown that the micro-particle, the surface roughness, the coated layer thickness and the atomic distribution of Ti, N and Fe elements are similar for the two cases regardless of the test deposition time from 10 to 180 minutes. However, it has been shown that the micro-hardness and the adhesion of the SKH51 steel are higher than the SKD11 steel, indicating that they are much affected by the hardness of the material to be coated.

• 한국태양에너지학회 논문집
• /
• 제22권3호
• /
• pp.57-65
• /
• 2002

The photocatalytic degradation of TCE using solar energy in POFR was studied. The use of solar energy was investigated in plastic optica fiber photocatalytic reactor (POFR). In POFR, the main parameters of photocatalytic degradation of TCE were lihgt intensity, thickness of $TiO_2$-coated film on plastic fiber core, the same of total $TiO_2$-coated surface area with changed length. We studied the apparent photonic efficiency and photocatalytic degradation rate of TCE in POFR. The apparent photonic efficiency of various light intensities was decreased by an incresed intensities. The photocatalytic activities of $TiO_2$-coated optical fiber reactor system depended on the coating thickness, and total clad-stripped surface area of POF. Photocatalytic degradation of trichloroethylene ($C_2HCl_3$, TCE) in the gas-phase was elucidated by using $TiO_2$-coated plastic optical fiber reactor. In TCE degradation, in-situ FTIR measurement resulted in mineralization into $CO_2$.

• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.361-364
• /
• 2003

It was investigated that the structural and electrical Properties of Ce-doped Ba(Zr$_{x}$Ti$_{1-x}$ )O$_3$ (BCZT) thin films with a mole fraction of x=0.2 and a thickness about 100 nm. BCZT films were prepared on Pt/Ti/SiO$_2$/Si substrate by a RF magnetron sputtering system. We have measured the thickness profile with Ar/O$_2$ ratio and the surface roughness. It was observed that the oxygen gas, which introduced during the film deposition, have an influence on the roughness of the film and the film roughness was reduced by annealing from 2.33 nm to 2.02 nm (RMS at 500 $^{\circ}C$, Ar:6 sccm, $O_2$:6 sccm). It was found that annealing procedure after top electrode deposit can reduce the dissipation factor.

• Tribology and Lubricants
• /
• 제24권5호
• /
• pp.250-254
• /
• 2008

The steam generator of nuclear power plant is composed with the bundles of long tubes. It is exposed fluid flow and weak in the vibration. The tubes are supported by anti-vibration bars. Due to vibration the wear damage is called as the fretting wear. It should be minimized for the safety of the plants. The hard coatings are very effective to reduce the amount of wear. The coatings of TiN and CrN are introduced in this study to protect the fretting surfaces. The tube-on-flat type tester was used for fretting wear tests. The results show that the wear amounts of the coated tubes were decreased depending on coating thickness. CrN was very effective to reduce the wear. In case of TiN the wear amounts were dependent on the coating thickness. Thick coating of TiN was very effective for wear resistance.

• 한국세라믹학회지
• /
• 제43권2호
• /
• pp.114-120
• /
• 2006

Nano-size Au particle doped $TiO_2$ films were prepared with $Ti(OC_3H_7^i)_4$, polyvinylpyrrolidone(PVP), $HAuCl_4$ and $C_3H_7OH$ etc. by sol-gel method. $TiO_2$ gel films were obtained by the dip-coating method on the $SiO_2$ glass substrates, and then heat-treated at $700^{\circ}C$ for 10 min. The thickness of $TiO_2$ films were $0.7\~1.8\;{\mu}m$. It was found that the thickness of films prepared from PVP containing solution was about $2\~8$ times higher values than that of thin films without PVP. The size of Au particles doped in the films were about $350\~750\;nm$. Nano-size Au particle dispersed $TiO_2$ films showed high absorption peak at visible region 450nm, which made them good candidates for non-linear optical materials and photo-catalytic materials. The contact angle of $TiO_2$ film for water was $12.5^{\circ}$, and therefore it is clear that $TiO_2$ films have very high hydrophilic properties and the self-cleaning effects.

• 열처리공학회지
• /
• 제6권2호
• /
• pp.70-78
• /
• 1993

The presence of a residual stress in a thin film affects the properties and performances of the film, so the study of stress in a film must be very important. In this study, therefore, considering the characteristics of PECVD process, it was discussed that the residual stress, measured by $sin^2{\Psi}$ method, fo TiN films deposited on substrates with different TECs (thermal expansion coefficients) changed with film thickness. As a results, it was obtained that the residual stress of TiN film was compressive stress about all kinds of substrates and increased with film thickness. Also, the compressive residual stresses of TiN films increased in Si, Ti, STS304 order. According to the above results, we confirmed that the changes of residual stress of TiN film with substrates were due to the thermal stress originated form the difference in the TECs of the film and substrates, and that the intrinsic stress had dominating effect on the residual stress of TiN film deposited by PECVD. And in this study, the intrinsic stress of TiN film was compressive stress in spite of the Zone 1 structure. It is due to the entrapment of impurities in grain boundary or void.

• Transactions on Electrical and Electronic Materials
• /
• 제2권2호
• /
• pp.37-41
• /
• 2001

Photo catalytic characteristics of nano-sized TiO$_2$ powder with rutile phase produced using homogeneous precipitation process at low temperatures (HPPLT) were compared with those of commercial P-25 powder by Degussa Co. The TiO$_2$ powder by HPPLT showed very higher photoactivity in the removal rate, showing lower pH values in the solution, than the P-25 powder when eliminating metal ions such as Pb and Cu from aqueous metal-EDTA solutions. This can be inferred the more rapid photo-oxidation or -reduction of metal ions from the aqueous solution, together with relatively higher efficiencies in the use of electron-hole pair formed on the surface of TiO$_2$ particle, under UV light irradiation. Also, in the view of the TiO$_2$ particle morphology, compared to the well-dispersed spherical P-25 particle, the agglomerated TiO$_2$ particle by HPPL T consists of acicular typed primary particle with the thickness ranged of 3∼7 nm, which would be more effective to the photocatalytic reactions without electron-hole recombination on the surface of the TiO$_2$ particle under the UV light irradiation. It is, therefore, thought that the higher photo activity of the rutile TiO$_2$ powder by HPPLT in the aqueous solutions resulted from having its higher specific surface area as well as acicular shape primary particle with very thin thickness.

• Bulletin of the Korean Chemical Society
• /
• 제32권12호
• /
• pp.4382-4386
• /
• 2011

$TiO_2$ hollow spheres were fabricated by using $SiO_2$ as an inorganic template. Spherical $SiO_2$ particles were coated by $TiO_2$ through the nucleation process, and then the core $SiO_2$ part was eliminated by using HF solution. Finally, $TiO_2$ hollow spheres were obtained. The size of the $TiO_2$ hollow spheres was about 300-400 nm and the thickness of the hollow wall was about 20-30 nm. The hollow has several holes whose diameters were within 100-200 nm. Dye-sensitized solar cells fabricated by using the $TiO_2$ hollow spheres were characterized. The solar conversion efficiency of the cell was 8.45% when $TiO_2$ hollow spheres were used as a scattering material, while it was 4.59% when $TiO_2$ hollow spheres were used as a normal electrode material.

• 열처리공학회지
• /
• 제3권1호
• /
• pp.1-7
• /
• 1990

To investigate the influence of r.f. power and electrode distance on the TiN deposition, TiN films were deposited onto STC3, STD11 steel and Si-wafer from gas mixtures of $TiC_4/N_2/H_2$ using the radio frequency plasma assisted chemical vapor deposition. The crystallinity of TiN film could be improved by the increase of r.f. power and the decrease of electrode distance. The TiN coated layer contains chlorine, its content were decreased with increasing r.f. power as well as decreasing electrode distance. And the thickness of deposited TiN was largely affected by r.f. power and electrode distance. The hardness of deposited TiN reached a maximum value of about Hv 2,000.