• 대한기계학회논문집
• /
• 제17권10호
• /
• pp.2467-2474
• /
• 1993

This paper deals with the cantilever subjected to a follower force which is generated by real rocket motor which has linearly decreasing thrust. The cantilever is assumed to be uniform and elastic one, In the theoretical analysis, the tip mass of rocket motor is considered as a rigid body and effects of its dynamic parameters are shown and compared with the experimental results. Particularly, the variation of the 2nd natural frequency due to the decreasing thrust is measured in the experiments and compared with the theoretical estimations. Approximate method is adopted in the theoretical analysis using Galerkin method by introducing 3-element modified operator and modified variable which represent eqation of motion and natural boundary conditions. In general, structural damping effects can be neglected and all the rigid body parameters must be taken into account in case of the short action time of the follower force and the relatively big tip mass like the system of this paper according to the experiment. Good agreement was obtained between the theoretical estimations and the experimental results by neglecting structural damping and considering all the rigid bidy parameters of the tip mass.

• 한국생산제조학회지
• /
• 제19권5호
• /
• pp.609-615
• /
• 2010

Angular contact ball bearings in a high speed spindles are under the extreme conditions, such as high temperature, big centrifugal force and thrust cutting forces. So, the assembly contacts between spindle shaft and inner ring bearings, bearing housing and outer ring of bearings are occasionally unstable at high speed revolution. Furthermore, the ball contact angle of a bearing, which influence stiffness and lifetime of bearings, are changed according to loads and rotational speed. To analyze internal forces of a bearing under high speed revolution, the ball contact are calculated using nonlinear equations in consideration of rotational speed, thrust loads and raceway form. Diameter increase of inner and outer ring by influence factors, such as internal forces to inner and outer ring, centrifugal force and temperature of inner and outer rings are calculated to establish stable state in bearing assembly in high speed spindle. Finally, contribution ratio of influence factor to assembly design tolerance of inner and outer rings are shown and the stable assembly design tolerance are proposed.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권1호
• /
• pp.65-72
• /
• 2005

Drilling process is one of the most common, yet complex operations among manufacturing processes. The performance of a drill is largely dependent upon drilling forces, Many researches focused on the effects of drill parameters on drilling forces. In this paper, an effective theoretical model to predict thrust and torque in drilling is presented. Also, with the predicted forces, the stress analysis of the drill tool is performed by the finite element method. The model uses the oblique cutting model for the cutting lips and the orthogonal cutting model for the chisel edge. Thrust and torque are calculated analytically without resorting to any drilling experiment, only by tool geometry, cutting conditions and material properties. The stress analysis is performed by the commercial FEM program ANSYS. The geometric modeling and the mesh generation of a twist drill are performed automatically. From the study, the effects of the variation of the geometric features of the drill and of the cutting conditions of the drilling on the drilling forces and the stress distributions in the tool are calculated analytically, which can be applicable for designing optimal drill geometry and for improving the drilling process.

• 한국정밀공학회지
• /
• 제15권3호
• /
• pp.31-37
• /
• 1998

The structure of satellite consists of six parts which are control system, power system, thermal control system, remote measurement command system, propellant system and thrust system. In these parts, propellant system consists of propellant tank and thrust device. What we want to perform is optimum design to minimize the weight of propellant tank. In order to design optimal propellant tank, several parameters should be adopted from the tank geometry like the relative location of the lug and variation of the wall thickness. The analysis was executed by finite element analysis for finding optimal design parameters. The structure was divided into three parts consisting of the initial thickness zone, the transitional Bone, and the weak zone, whose effects on the pressure vessel strength was investigated. Finally the optimal lug location and the three zone thickness were obtained and the weight was compared with the uniform thickness vessel.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.399-404
• /
• 2010

추진제 주입압력 350 psia 에서 0.95 lbf 의 정상상태 공칭추력을 내는 단일액체추진제 하이드라진 추력기의 펄스모드 시험 결과를 추진제 공급압력, 추력기 작동환경 진공도, 그리고 추력펄스 등의 변이와 함께 추력기의 열적 반응거동과 더불어 제시한다. 시험자료는 임펄스 비트, 진공 비추력, Force Centroid 등의 펄스모드 성능특성인자로 변환되어 상세한 분석이 이루어지고, 1 lbf급 표준형 단일추진제 로켓엔진의 펄스모드 기준성능과 성공적으로 비교된다.

• 한국항공운항학회지
• /
• 제14권3호
• /
• pp.1-6
• /
• 2006

The altitude engine test is a sort of engine performance tests carried out to measure the performance of a engine at the simulated altitude and flight speed environments prior to that at the flight test. During the performance test of a engine, various values such as pressures and temperatures at different positions, air flow rate, fuel flow rate, and the load by thrust are measured. These measured values are used to derive the representative performance values such as the net thrust and the specific fuel consumption through a momentum equation. Hence each of the measured values has certain effects on the total uncertainty of the performance values. In this paper, the combined standard uncertainties of the performance variables at the engine test were estimated by the uncertainty analysis of the measurement values and the repeatability and reproducibility of the altitude test measurement were assessed by the analysis of variation on the repeated test data with different operator groups.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.310-315
• /
• 2008

Authors design a rotary-type small-scaled linear induction motor(LIM) and a performance test machine before manufacturing a real-scaled LIM for a railway transit. The designed LIM is a single-sided, short primary type and its primary has 4 poles. The rated power is 10(kW). In order to analyze characteristics of the LIM, authors use a mixed 2D-3D FEM analysis. 3-D FEM analysis is used for calculating a distribution of eddy-current on the semi-caped AL-sheet of the secondary reaction. Authors calculate a correction factor of conductivity and an equivalent conductivity on the secondary AL-sheet using a normalized eddy-current. The equivalent conductivity which is calculated in this way includes a transverse edge-effect of the LIM. Authors apply the equivalent conductivity on the secondary AL-sheet of 2D-FEM model and get performance characteristics of the LIM. Basic characteristics such as thrust and normal force, input current, efficiency and power factor of the LIM have been analyzed with the variation of frequency and speed. In order to apply an air-gap control system, the variation of the basic characteristics have been analyzed with the air-gap length variation of the LIM. Finally, authors introduce an operation mode using the air-gap control system and conduct a research on feasibility of the system.

• 대한조선학회논문집
• /
• 제41권5호
• /
• pp.21-27
• /
• 2004

A waterjet propulsion system has many advantages compared with a conventional screw propeller especially for amphibious military vehicles because of a good maneuverability at low speed, good operating ability at shallow water, high thrust at low speed to aid maneuverability and exit from water, etc. Especially, compact design is important for the tracked-vehicle because of buoyancy in water and available space inside the tracked vehicle. The experiment is parametrically performed for various impeller diameters for more compact design. The experimental results are analyzed according to the ITTC 1996 standard analysis method as well as the conventional propulsive factor analysis method. The full-scale effective and delivered power of the tracked-vehicle are evaluated according to the variation of impeller diameter. This paper emphasized the effect of impeller diameter on the performance of waterjet system.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.141-145
• /
• 2004

The objective of the present study is to conduct model combustion tests for various injectors to identify their combustion stability characteristics. Three different double swirl coaxial injectors with variation of a recess length have been tested for the comparative study of CH flame structure and dynamic characteristics. Gaseous oxygen and mixture of gaseous methane and propane have been employed for simulating actual propellants used for a full-scale thrust chamber. Upon test results, the direct comparison between various types of injectors can be realized for the selection of the best design among prospective injectors.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.7-12
• /
• 2003

In this paper, S(stochastic)-eigenvalue concept and its S-eigenvector for linear continuous-time systems with probabilistic uncertainties are proposed. The proposed concept is concerned with the perturbation of eigenvalues due to the probabilistic variable parameters in the dynamic model of a plant. S-eigenstructure assignment scheme via the Sylvester equation approach based on the S-eigenvalue concept is also proposed. The proposed design scheme is applied to the longitudinal dynamics of open-loop-unstable aircraft with possible uncertainties in aerodynamic and thrust effects as well as separate dynamic pressure.