• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.32-38
• /
• 2004

A comprehensive understanding is given for the hot-firing test results, which were obtained throughout the verification program of mono-propellant hydrazine rocket engines (thrusters) producing 0.95 lbf (4.2 N) of nominal steady-state thrust at an inlet pressure of 350 psia (2.41 Mpa). A scrutiny for the engine performance is made in terms of thrust and temperature behavior of steady state firing mode at the given propellant injection pressures: Pinj = 400, 250, 100, and 50 psi. The thrust and specific impulse are compared with a reference performance of 1-lbf standard rocket engines and their normalization procedure is introduced. A practical engineering approach to the data measurement and reduction is addressed, too.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.9
• /
• pp.122-129
• /
• 2004

An accurate thrust measurement is one of the critical paths to the successful test and evaluation program of small liquid propulsion engines. This study describes the design factors for the development of thrust measurement system (TMS) as well as manufacturing practice of TMS hardware. We investigate characteristics of the TMS and its performance through hot-firing test of small liquid engine in a vacuum test cell which is capable of simulating 100,000 ft of altitude or higher. For performance test of TMS, we measure thrusts by changing propellant injection pressure at steady state firing mode as well as at pulse firing mode. Measured eigen frequency of the TMS is 67 Hz. Linearity test of the TMS shows good performance with less than 0.5% of linearity error.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.6
• /
• pp.98-104
• /
• 2015

Excessive thrust acting on the rotor of pump can cause the damage of pump or the decrease of pump lifetime. Therefore, for ensuring the safety of LOX pump of a liquid rocket engine, the thrust of pump rotor is estimated by similarity tests. Axial thrust is indirectly measured by an axial thrust measurement unit positioned outside pump. Radial thrust is calculated based on pressure distribution of volute scroll. As a result, axial and radial thrust are increased when the flowrate of pump decreases. However, both thrusts do not affect the stability of pump rotor since their values are not large.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.6
• /
• pp.46-50
• /
• 2012

A high-speed centrifugal pump requires more attention to the control of its axial thrust due to the high discharge pressure than a conventional industrial pump. Vanes employed toward the rear cavity of the impeller can be an effective device to control the axial thrust of the pump. The vanes disturb circumferential flow of the cavity and it can modify the axial force acting on the impeller. In this paper, three types of vanes are installed in the high-speed centrifugal pump for liquid rocket engines and the thrust of the pump is measured with an additional thrust measurement unit. According to the results, shapes of cavity vanes have effects on the axial thrust of the pump. As the height of vanes increases, the outlet pressure of the rear floating ring seal decreases which results in a decrease of the thrust. On the other hand, head of the pump is almost same regardless of cavity vanes. Also, the pressure drop of the bypass pipeline increases when vanes are removed.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.428-431
• /
• 2008

Korea Aerospace Research Institute(KARI) is achieving the Korea Space Launch Vehicle(KSLV) program according to National Space Technology Development Program. KSLV-I will be composed to liquid propellant(first stage) and solid propellant(second stage) propulsion system. The propulsion system of KSLV-I second stage is solid kick motor with high expansion ratio and its starting altitude is 300km high. In order to verify the performance of upper stage propulsion system designed to operate in the upper atmosphere, test facility which can simulate high altitude is needed. High Altitude Simulation Test Facility is composed to Thrust Measurement System, Control & Measurement system, Diffuser, SKID for cooling water supply to diffuser, CCTV, fire protection system and so on. This paper introduces TMS adapted to High Altitude Simulation Test for KSLV-I Kick Motor Development and results of hot firing test for its performance verification.

• Journal of Aerospace System Engineering
• /
• v.15 no.5
• /
• pp.60-71
• /
• 2021

Propeller performance measurement system for commercial propeller was designed and applied to the wind tunnel test for 3 commercial propeller models with diameters of 30 inch. The thrust and torque of the propeller was directly measured by using 6-components balance installed on the rotating axis. The measurement system was validated by using wind tunnel balance calibration equipment. Propeller test stand including measurement and rotating system was validated by using QTP propeller. In the hovering condition, we compared the performance test results and the specifications of the commercial propeller provided by the manufacturer and confirmed that there are differences in the thrust and the torque. We measured the propeller performance with various wind speeds, propeller models and angles of attack and was summarized by thrust coefficients. We confirmed that the trend of the thrust coefficients was different in the low angle of attack and high angle of attack. An aerodynamics database that can be used for future aerodynamic design of an unmanned aerial vehicle was secured.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.227-232
• /
• 2003

Usually, the thrust of a Linear Pulse Motor(LPM) is calculated by magnetic equivalent circuit modelling method. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force Method. For calculating accuracy thrust by using these every method, the thrust is calculated and compared by Lorentz Force Method, Magnetic Coenergy Method, and Maxwell correspondence force Method. And that becomes important factor at the comparison of each capacity and parameter of motor. So this study wants to compare and analyze measurement data and calculating data of the static thrust of LPM. and then we can get more accuracy method, calculating the static thrust of LPM.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.6
• /
• pp.111-117
• /
• 2018

In this study, an MEMS thrust measurement system was designed and a study on the performance prediction of system was performed to evaluate the performance of micro thruster. Thrust measurement system consists of beam, membrane, and piezoresistive sensor. An FEM analysis was carried out to verify the stability of the system, confirm the stress variation at the beam, and position the piezoresistive sensor. The stability of the designed system was verified by comparing the yield strength of the material with the maximum stress. The piezoresistive sensor was designed to be 20% of the length of the beam to obtain a high gauge factor. The size of the membrane and the beam of the reference model were designed to be $15mm{\times}15mm$, and $500{\mu}m{\times}500{\mu}m$, respectively.

• Journal of Power System Engineering
• /
• v.13 no.4
• /
• pp.62-67
• /
• 2009

In this paper we designed a prototype hybrid type linear pulse motor (HLPM) with single side stator structure for low cost. The measurement system which can get the motor characteristics of the HLPM was suggested. The static and dynamic characteristics of the thrust force are measured analyzed. And the microstep drive method is adopted and tested to the drive of prototype HLPM. The thrust waveform is measured respectively to know the differences of the thrust waveform between the microstep drive method and rectangular wave. From the experimental results, it can be confirmed that the repetitive ripple of the thrust force of the prototype HLPM is reduced by taking the microstep drive method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.9-17
• /
• 2006

The thrust measurement systems(TMS) with high accuracy are required in rockery, according to develop the high precise guided space vehicle. For obtaining high accuracy, the basic concepts and the necessary technology which have been acquired through many experiences of TMS are summarized, and the design methodology for practical use in ADD is presented. In this paper, the parameters against accuracy of TMS are discussed, and the improving methods are suggested. Through this application example, the design methodology of ADD is shown its superiority in TMS.