• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.948-954
• /
• 2008

In this study, vibrational characteristics of two nano-imprinting stages is analyzed and compared with respect to the methodology to support the upper-plate of the stage. The first type of the stage has three supporters at each corners of the stage and one thrust bearing at the center of the stage. The other type of the stage has four supporter in each corner of the stage without a thrust bearing. The FEM software with flexible modeling is used for the normal mode analysis. The result depicts the difference of vibrational characteristics caused by the difference of support methods. The design criteria for the precision nano-imprinting stage is also discussed.

• 항공우주기술
• /
• 제9권2호
• /
• pp.8-13
• /
• 2010

축추력의 효과적인 제어는 터보펌프의 작동 안정성을 확보하는 데 중요한 기술 중 하나이다. 현재 개발 중인 75톤급 로켓엔진용 연료펌프에 대한 축추력 측정을 상온의 물을 매질로 하여 실시하였다. 시험 결과, 연료펌프의 축추력은 펌프 베어링의 축방향 하중 조건을 만족하는 것으로 예상되었다. 또한 연료펌프의 축추력은 대체로 유량이 작을수록 커졌다. 그리고 플로팅 링 실과 임펠러 사이의 간극이 바뀌었을 때, 연료펌프의 축방향 하중과 후방 누설 유량이 변화하는 것을 확인하였다.

• KSTLE International Journal
• /
• 제1권2호
• /
• pp.107-112
• /
• 2000

In case of the limitation of Deep RIE fabrication far Micro Gas Turbine, bearing aspect ratio is limited in very small value. The characteristics such as pressure distribution, load capacity and non-linearity of a short bearing of L/D=0.083 and a conventional bearing of L/D=1.0 with coupled boundary effects are investigated for Micro Gas Turbine bearings. The coupled effect was analyzed by mass conservation at coupled end area. The results, increasing load capacity and non-linearity due to the coupled effect of thrust and journal bearing, are obtained and the selection of journal bearing type is discussed.

• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.467-475
• /
• 2001

Feasibility study of gas-lubricated bearing in micro gas turbine was performed. Based on Reynolds equation, finite difference method with coupled boundary was developed to analyze bearing characteristics, such as load capacity, mass flow rates and stiffness. By the bearing force and mass flow rates analysis with the variation of supply pressure, bearing clearance and capillary radius, acceptable range of design parameters were suggested in terms of load capacity and stiffness of bearings. Additionally, coupled boundary effect on pressure distribution was investigated and it is stated that coupling could reduce an excitation force due to narrow pressure distribution.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.273-281
• /
• 2001

Feasibility study of gas-lubricated bearing in micro gas turbine was performed. Based on Reynolds equation, finite difference method with coupled boundary was developed to analyze bearing characteristics, such as load-carrying capacity, mass flow rates and stiffness. By the bearing force and mass flow rates analysis with the variation of supply pressure, bearing clearance and capillary radius, acceptable range of design parameters were suggested in terms of load capacity and stiffness of bearings. Additionally, coupled boundary effect on pressure distribution was investigated and it is stated that coupling could reduce all excitation force due to narrow pressure distribution.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.243-249
• /
• 2000

In case of the limitation of Deep RIE fabrication for Micro Gas Turbine, bearing aspect ratio is limited in very small value. The characteristics such as pressure distribution load capacity and non-linearity of a short bearing of L/D=0.083 and a conventional bearing of L/D=1.0 with coupled boundary effects are investigated far Micro Gas Tlubine bearings. The coupled efffect was analyzed by mass conservation at coupled end area. The results, increasing load capacity and non-linearity due to the coupled effect of thrust and journal bearing, are obtained and the selection of journal bearing type is discussed.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1997년도 제25회 춘계학술대회
• /
• pp.91-100
• /
• 1997

In this paper the linearzed stiffness and damping coefficients of tilting pad thrust bearing are calculated by the perturbation method. The coefficients are obtained for a wide range of pivot positions. The effects of exciting frequency and pad mass on stiffness and damping coefficients are investigated. Critical frequencies due to the tilting motions of the pad are presented and are shown to be strongly influenced by the pivot position and pad mass.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.66-69
• /
• 1999

This study aims at the improvement on the process and die set required for forming of flanged two-piece thrust engine bearings form laminated sheet blanks. Several suggestions are made to reduce the number of forming or subsequent machining processes or to improve the dimensional precision of formed products. The results of finite element analysis show the design suggested in this study are useful and applicable to the forming process of flanged bearings.

• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.33-41
• /
• 1997

In this paper the linearized stiffness and damping coefficients of tilting pad thrust bearing are calculated by the perturbation method. The coefficients are obtained for a wide range of pivot positions. The effects of exciting frequency and pad mass on stiffness and damping coefficients are investigated. Critical frequencies due to the tilting motions of the pad are presented and are shown to be strongly influenced by the pivot position and the pad mass.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.407-413
• /
• 2008

This paper investigates the dynamics of a HDD spindle system due to the change of FDBs. Flying height of the HDD spindle system is determined through the static analysis of the FDBs, and the stiffness and damping coefficients are calculated through the dynamic analysis of the FDBs. Free vibration characteristics and shock response of the HDD spindle system are analyzed by using the finite element method and the mode superposition method. Experimental modal test is also performed to verify the accuracy of the proposed method. This research shows that the stiffness coefficients of journal heating mostly affect the rocking frequencies because their magnitude are within the range of the stiffness of supporting structure. It also shows that the damping coefficients of thrust bearing mostly affect the axial frequency because the stiffness of thrust bearing is much smaller that that of supporting structure.