• Journal of Chest Surgery
• /
• v.30 no.12
• /
• pp.1225-1231
• /
• 1997

Spontaneous pneumothorax is the sudden collapse of a lung usually caused by air leakage from a subvisceral pleural blob. Responses to closed thoracostomy,thoracentesls and simple observation are usually prompt and effective. But in some cases, these are unsucceful and open thoracotomy is indicated. A clinical evaluation was performed on 242 cases(236 patients) of open thoracotomy in spontaneous pneumoth rax who were admitted and treated at department of Thoracic and Cardiovascular Surgery. Masan Samsung General Hospital during the past 9 years from January 1988 to December 1996. The results were as follows 1. The sex ratio was male predominance(M:F=11.7:1) 2. The most common age group were 2nd, 3rd decades(2nd=29.3%, 3rd=30.2%). 3. The most common chief complaints were chest pain and dyspnea(chest pain=41.7%. dryspnea= 36.8). 4. The etiologic factors of spontaneous pneumothorax were primary spontaneous pneumothorax(86.4%), tuberculosis(9.1%), COPD(3.7%) and pleuritis(0.8%). 5. The site of spontaneous pneumothorax was 52.1% in right, 45.4% in left and 2.5% in both. 6. The common indications of open thoracotomy were recurrence(44.2%), persistent air leakage(31.8%) and inadequate expansion(15.7%). 7. The operative procedures were bullectomy or mechanical pleurodesis through posterolateral thoracotomy or median sternotomy. 8. The most frequent location of bulla or blob were apical segme t oi RUL(35.1%) and apicoposterior segment of LUL(41.3 %). 9. The number of bulla or blob were mainly 1 to 5(88%), and there were no significant differences among operation indications. 10. The size of bulla or bleb were mainly below 5cm(81%)and small bulla($\leq$1cm) were predominant in recurrence group but large bulla(>5cm)were predominant in persistent air leakage and inadequate expansion group. 11. The pleural adhesion was seen in 54.5%.(Recurrence group 64.1%,Persistent air leakage group 51.9%,Inadequate expansion group 47.4%).

• Journal of Chest Surgery
• /
• v.30 no.12
• /
• pp.1237-1241
• /
• 1997

Tracheal stenosis is a difficult disease entity to manage. Laser ablation is one effective treatment for treacheal stenosis and can be utilized if tracheal reconstructive surgery is impossible. Potassium titanyl phosphate laser, transmitted via flexible quartz fiber, can be precisely manipulated through flexible bronchoscope under local anesthesia. We treated 7 patients with trach al and broncheal lesion under local anesthesia with KTP laser from January 1995 to July 1996. The patients included three males and four females. The age of patients ranged from 22 to 66 years with a mean of 43.7 years The etiology of tracheal stenosis in patients was stenosis after tracheostomy(3 cases), prolong inturbation in cases of sepsis(1 cases), and the recurrence of lung cancer within endobronchial lesion(2 cases). In the cases of tracheal stenosis treated with laser ablation, there were 2 cases of recurrence of stenosis at the anastomosis site after the operation, 3 cases of stenosis at tracheostomy site, and 2 cases of local recurrence of lung cancer. The site of the tracheal stenosis was the balloon site of the tracheostomy tube(3-4cm inferior to the tracheostomy site, 2-3cm superior to the carina) and the anastomosis site that were narrowed to less than 5mm(4 cases). For the stenosis lesion in the endobronchial area, there were 2 patients with a lesion at the anterior wa l, 1 patient with a lesion at the posterior wall, 2 patients with circumferential stenosis. Laser ablation time was 25.4 $\pm$5.9min and used energy was 1768 $\pm$365J. We have used KTP laser via (lexible bronchoscope without major complications. Adjuvant radiation therapy may prevent fibroblast proliferation which leads to restenosis. In three patients of restenosis after laser ablation, adjuvant irradiation started within 4 hours after laser ablation, and the radiation doses were 1500cGy given in five fraction. In patients with adjuvant radiation therapy, stenosis has not recurred

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.1 no.1
• /
• pp.11-23
• /
• 2003

A study on the electrolytic dissolution of SUS-304 and Inconel-600 specimen was carried out in neutral salt electrolyte to evaluate the applicability of electrochemical decontamination process for recycle or self disposal with authorization of large amount of metallic wastes contaminated with uranium compounds generated by dismantling a retired uranium conversion plant in Korea. Although the best electrolytic dissolution performance for the specimens was observed in a Na2s04 electrolyte, a NaNO$_3$ neutral salt electrolyte, in which about 30% for SUS-304 and the same for Inconel-600 in the weight loss was shown in comparison with that in a Na$_2$SO$_4$ solution, was selected as an electrolyte for the electrochemical decontamination of metallic wastes with the consideration on the surface of system components contacted with nitric acid and the compatibility with lagoon wastes generated during the facility operation. The effects of current density, electrolytic dissolution time, and concentration of NaNO$_3$ on the electrolytic dissolution of the specimens were investigated. On the basis of the results obtained through the basic inactive experiments, electrochemical decontamination tests using the specimens contaminated with uranium compounds such as UO$_2$, AUC (ammonium uranyl carbonate) and ADU (ammonium diuranate) taken from an uranium conversion facility were performed in 1M NaNO$_3$ solution with the current density or In mA/$\textrm{cm}^2$. it was verified that the electrochemical decontamination of the metallic wastes contaminated uranium compounds was quite successful in a NaNO$_3$ neutral salt electrolyte by reducing $\alpha$ and $\beta$ radioactivities below the level of self disposal within 10 minutes regardless of the type of contaminants and the degree of contamination.

• Korean Security Journal
• /
• no.32
• /
• pp.65-93
• /
• 2012

The purpose of this study is to identify problems of private security guard playing an important role at the front of private security industry effectively by examining correlation between job stress and job satisfaction of private security guard and present proposals of effective operation of private security industry. Through data analysis according to study methods and procedures mentioned above, below conclusions were obtained. First, as results of analyzing correlation between job stress and work satisfaction of private security guard, one of subsidiary job satisfaction factors, it was found that lower stress to role complications and wage system relates to higher work satisfaction. Second, as results of analyzing correlation between job stress and superior satisfaction of private security guard, one of subsidiary job satisfaction factors, it was found that lower stress to wage system, responsibility, and role complications relates to higher superior satisfaction. Third, as results of analyzing correlation between job stress and equal opportunity satisfaction of private security guard, one of subsidiary job satisfaction factors, it was found that lower stress to wage system, responsibility, and role complications relates to higher equal opportunity satisfaction. Forth, as results of analyzing correlation between job stress and welfare satisfaction of private security guard, one of subsidiary job satisfaction factors, it was found that lower stress to wage system and role complications relates to higher welfare satisfaction. Fifth, as results of analyzing correlation between job stress and wage satisfaction of private security guard, one of subsidiary job satisfaction factors, it was found that lower stress to wage system and role complications relates to higher wage satisfaction. Sixth, as results of analyzing correlation between job stress and job pride, one of subsidiary job satisfaction factors, it was found that lower stress to wage system and role complications relates to higher job pride. Seventh, as results of analyzing correlation between job stress and co-worker satisfaction, one of subsidiary job satisfaction factors, it was found that lower stress to wage system and role complications relates to higher co-worker satisfaction.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.4
• /
• pp.446-455
• /
• 2015

Based on comparative studies on standards and grading procedures of machine graded lumber in Korea and other countries, this study proposed a procedure of determining the grade classification and design strengths of domestic machine graded lumber. Differences between machine stress rated lumber and E-rated laminations were detailed in order to clarify the need for the procedure improvement. To this improvement the use of average MOE requirement for grading was introduced instead of the fixed minimum MOE requirement which is currently used in the Korean standards. It was found that the fixed minimum MOE requirement method was easier for an inspector to grade but, less efficient as a strength predictor than the average MOE requirement method. The advantage of average MOE requirement method is statistically MOR-MOE regression-based MOR prediction and highly efficient in quality control though it requires a computer-aided operation system in an initial setup. A major weakness of the current Korean grading system was found that different strength characteristics depending on wood species were not reflected on the grade classification and the tabulated allowable design stress. The proposed procedures were developed taking advantages of respective merits of both methods and based on MOR-MOE regression analysis. Through this procedure, the grades of machine stress rated lumber should be revised to become interchangeable with E-rated lamination, which would be beneficial to the cost competitiveness of domestic machine graded lumber and glued laminated timber industry.

• Journal of Korea Water Resources Association
• /
• v.48 no.12
• /
• pp.1065-1075
• /
• 2015

In the estuary where the structure such as river-mouth weir has been installed, the flow is developed very complicatedly due to river water from upstream, tide of the sea and floodgate operation. Especially, if basin outlets more than one exists in one estuary, the boundary conditions will be significantly more complex form. Saemangeum(SMG) project area in Korea is the most typical example. There are Mankyung river and Dongjin river in upstream. The water of them inflows into SMG project area. In the downstream, river flow was drained from inland to sea over the SMG sea dike through the sluice. The connecting channel was located between Mankyung and Dongjin basins. It functions not only as transportation by ship in ordinary period but also as flood sharing by sending flood flow to each other in flood period. Therefore, in order to secure the safety against flood, it is very important to understand the flood sharing capacity for connecting channel. In this study, the flood control effect was analyzed using numerical simulation. Delft3D was used to numerical simulation and simulated period was set up with neap tide, in which the maximum flood stage occurred due to poor drainage. Actually, three connecting channels were designed in land use plan of the SMG Master Plan, but they were simplified to a single channel for conciseness of analysis in this study. According to the results of numerical analysis, the water level difference between two basins was increased and the maximum flood stage at dike sluice was also upraised depending on decrease of conveyance. And the velocity induced by same water level difference was decreased when the conveyance became smaller. In certain conveyance above, there was almost no flood control effect. Therefore, if the results of this study are considered for design of connecting channel, it will be expected to draw the optimal conveyance for minimizing dredging construction cost while maximizing the flood control effect.

• Journal of Chest Surgery
• /
• v.30 no.8
• /
• pp.786-792
• /
• 1997

A clinical study of 71 cases of pulmonary tuberculosis that had had surgical resection during the period of 7 years and 6months from January 1989 to June 1996 in National Masan Tuberculosis Hospital. The results were as follows. 1. The ratio of male to female was 3.7:1 and in the age incidence the fourth decade was 22%, the third decade 15%. Although medical treatment was performed for more than 3 to 6 months, preoHeratively the conversion failure rate of positive sputum to negative state was 66.2%(47 cases). Of the failure cases, multiple-drug-resistant(MDR) patients were 41 cases(87.2%), 3. In MDR group, preoperatively conversion failure rate was 71.9%. 4. From the view of indica ion for lung resection on the radiographic finding, cavitary lesions were 43 cases(60.6%), destroyed lung lesions were 24 cases(33.8%). 5. The incidence of postoperative complication was 28.2%(20 cases). All cases were MDR 6. group and the most common of complication was tuberculosis spreading. In bilateral lesion, incidence of postoperative tuberculosis spreading was 25%(7 cases). Of the 7 cases, there was the cavitary lesion in 6 cases(86.7%). Total conversion rate of AFB positive sputum to negative state related to resectional sugery was 76.6% and in MDR group conversion rate of AFB positive sputum to negative state was 73.2% Conversion rate of MDR group with bilateral lesion was the lowest(60%). Conversion rate of drug-sensitivity group was 100% regardeless of lesions Slt to. In conclusion, despite of long-standing medical treatment, it is difficult to converse sputum-positive to negative state in multiple-drug resistance patients and that increases postoperative complications su h as tuberculosis relapse as a lack of appropriate drugs postoperatively. Postoperative conversion rate of sputum-positive to negative state was decreased in multiple-drug resistance patients. Because multiple-drug resistance patients have inireased due to several factors in Korea, it is important to prevent spreading of multiple-drug resistnce patients through the aggressive operative treatment. When the first medical therapy is fail or drug-resistance is found, operative treatment should be considered with the secondary medical therapy. The operation should be aggressively attempted even though at first medical treatment if indicated.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.1
• /
• pp.3263-3291
• /
• 1974

Experimental work of grain bin was carried out to develop the methods of natural air in-bin drying and storage. The method is considered to be more economical, labour saving, and an effective countermeasure to grain loss. To examine the possibility of farm use of the grain bin and to analyze the related factors concerned with in-bin grain drying and storage, ambient air conditions (especially the change of air temperature and relative humidity) and grain quality during drying and storage periods were investigated. A laboratory model bin was constructed to investigate the effect of different forced air conditions on the drying characteristics of rice. In addition, a grain bin with 2.2m diameter and 1.8m height, considered to be the optimum size for the average Korean farm, was constructed and tested to examine the drying and storing characteristics of rice. The weather data analyzed in this study was the nine-year (from 1964 to 1972) record of air temperature and relative humidity in the Suweon area, and the thirty-year (from 1931 to 1960) record of pentad normal relative humidity and air temperature in the Seoul area. From the results of the weather data analyses, the adequate air delivery hours (which was arbitrary defined as the condition to give less than 75% relative humidity) to dry the rice during October were about nine hours (from approximately 10 A.M. to 7 P.M, ) a day, in which the average air temperature was about 15.9$^{\circ}C$ and average relative humidity was 66%. The occurence of days having three hours of such conditions was 1, 2, and 1-day within the 1st, 2nd add last 10-day periods for the month of October, respectively. Therefore, it may be considered that the weather condition in October was satisfactory for the forced natural air drying. The results of the laboratory model bin test were analyzed to obtain the drying curve and drying rate for different drying stages and grain layers in the bin corresponding to various conditions of forced natural air. A drying experiment with a prototype grain bin showed that an approximate 5 percent grain moisture gradient through a 1.6 meter grain deposit was observed after 80 hours of intermittent drying, giving an over dried zone in the lower grain layers and an extremely high grain moisture zone in the upper layers. This indicates that an effective measure should be taken to reduce this high moisture gradient. In order to investigate the drying characteristics of bulk grain in a layerturning operation a grain bin test was performed. This showed a significant improvement of uniform drying. In this test, approximate 107 hours were required to dry a depth of 1.6 meter of grain from an initial moisture content of 22.2 percent to a moisture content of 16.7 percent using an air delivery rate of 2.8 cubic meter per a minute per every cubic meter of grain. This resulted in a 2 percent moisture gradient from the top to the bottom of the bin. During storage period, till the end of June the average temperature of grain was 2~3$^{\circ}C$ higher than ambient air temperature. But during July when the grain moisture content went up slightly (less than 1 percent), the average temperature of the grain also increased to 3~5$^{\circ}C$ higher than ambient air temperature. It is therefore recommended that for safe grain storage, grain should not be stored in sheet metal bins after mid May. From the above results, in-bin rice drying and storage can be used effectively on Korean farms. It is strongly recommended that the use of grain-bin system should be implemented for farm use to improve farm drying and storage of rice.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.06a
• /
• pp.110-120
• /
• 2005

For utilizing vitrification to treat low and intermediate level waste, industrial pilot plant was designed and constructed in October 1999 at Daejon, Korea through the joint research program among NETEC, MOBIS and SGN. More than 70 tests were performed on simulated IER, DAW etc. including key nuclide surrogate(Cs, Co); this plant has been shown to vitrify the target waste effectively and safely, however, some dust are generated from the HTF(High Temperature Filter) as a secondary waste. In case of long term operation, it is also concerned that pipe plugging can be occurred due to deposited dust in cooling pipe namely, connecting pipe between CCM(Cold Crucible Melter) and HTF. In this regard, we have developed the special complementary system of the off-gas treatment system to recycle the dust from HTF to CCM and to remove the interior dust of cooling pipe. Main concept of the dust recycling is to feed the dust to the CCM as a slurry state; this system is regarded as of an important position in the viewpoint of volume reduction, waste disposal cost and glass melt control in CCM. The role of DRS(Dust Recycling System) is to recycle the major glass components and key nuclides; this system is served to lower glass viscosity and increase waste solubility by recycling B, Na, Li components into glass melt and also to re-entrain and incorporate into glass melt like Cs, Co. Therefore dust recycling is helpful to control the molten glass; it is unnecessary to consider a separate dust treatment system like a cementation equipment. The effects of Dust Cleaner are to prevent the pipe plugging due to dust and to treat the deposited dust by raking the dust into CCM. During the pilot vitrification test, overall performance assessment was successfully performed; DRS and Dust Cleaner are found to be useful and effective for recycling the dust from HTF and also removing the dust in cooling pipe. The obtained operational data and operational experiences will be used as a basis of the commercial facility.

• Archives of design research
• /
• v.16 no.1
• /
• pp.181-198
• /
• 2003

The purpose of this study is to develop a on-line design tool for effectively coping with e-Business environment, or product design process into a Cyber model for traditional manufacturers which attempts new product development under such environment. It was finally developed as a model named $\ulcorner$Design Vortal Site; e-BVDS) that was based on the structure and style of internet web site. Results of the study can be described as follows ; \circled1 e-Business is based on the Internet. All processes in the context of e-Business require models whose structure and method of use are on-line styles. \circled2 In case that a traditional manufacturing business is converted into e-Business, it is better to first consider Hybrid Model that combines resources and advantages of both such traditional and digital businesses. \circled3 The product design process appropriate for e-Business environment has to have a structure and style that ensure utilization of the process as an Internet web site, active participation by product developers and interactive communication between participants in designing and designers. \circled4 $\ulcorner$e-BDVS) makes possible the use of designers around the wend like in-house designers, overcoming lack in creativity, ideas and human resources traditional business organizations face. However, the operation of $\ulcorner$e-BDVS$\lrcorner$ requires time and budget investments in securing related elements and conditions. \circled5 Cyber designers under $\ulcorner$e-BDVS$\lrcorner$ can easily perform all design projects in cyber space. But they have some limits in playing a role as designers and they have difficulty in getting rewards if such projects completed by them are not finally accepted. \circled6 $\ulcorner$e-BDVS) ensures the rapid use of a wide range of design information and data, reception of a variety of solutions and ideas and effective design development, all of which are not possible through traditional processes. However, this process may not be suitable to be used routine process or tool. \circled7 $\ulcorner$e-BDVS$\lrcorner$ makes it possible for out-sourcing or partners businesses to overcome restrictions in time and space and improve productivity and effectiveness. But such they may have to continue off-line works that can not be treated on-line.