• 한국추진공학회지
• /
• 제24권4호
• /
• pp.12-24
• /
• 2020

이중목 노즐은 유체 추력벡터제어 분야에서 특히 효과적인 방법이며, 다른 축소부가 종래의 축소-확대 노즐의 확대부에 연결된다. 본 연구에서는 3차원 초음속 직사각형 노즐에서 추력벡터제어 성능에 대한 분사각의 영향을 조사하기 위하여 수치해석을 수행하였다. 5개의 분사각에 대하여 다루었으며, 편향각도, 분사 질량유량비, 시스템 전체 추력비, 전체 피칭 추력효율, 대칭면에서의 마하수 분포와 유선 및 다른 면에서 마하수 분포를 포함하는 임계 성능변화가 정량적으로 그리고 정성적으로 분석되었다. 본 연구의 결과는 특히 전투기 설계자에게 유용한 기술적 자료를 제공한다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.363-366
• /
• 2006

본 연구에서는 초음속 공동유동장에서 발생하는 압력 진동을 완화시키기 위하여 사용된 두 가지 피동제어방법들의 유효성을 수치해석적으로 조사하였다. 사용된 제어 장치들은 삼각돌기와 sub-cavity로, 전단층의 발달 특성을 조절하기 위하여 공동 전단 부근에 설치된다. 공동유동의 압력변동 특성을 조사하기 위하여 3차원 비정상 Navier-Stokes 방정식에 유한체적법을 적용하여 유동장을 모사하였으며, 유동의 난류상태량들은 LES 방법을 사용하여 계산하였다. 그 결과, 공동유동의 진동 특성은 공동의 후단 벽면에서 발생하는 압력 진동에 의해 지배되며, 제시된 방법들의 효과는 공동의 후단에서 가장 크게 나타났다. 특히, sub-cavity는 삼각돌기나 블로잉이 있는 경우에 비하여 압력 진동 저감효과가 상대적으로 크며, sub-cavity가 큰 경우 압력 진동의 저감효과가 더욱 뚜렷하게 나타났다.

• International Journal of Aeronautical and Space Sciences
• /
• 제13권3호
• /
• pp.349-360
• /
• 2012

In this study, the accuracy of CSD (Comprehensive Structural Dynamics) analysis on the evaluation of blade aeroelastic responses and structural loads of HART(Higher harmonic Aeroacoustic Rotor Test) II baseline rotor is assessed using a comprehensive rotorcraft dynamics code, CAMRAD II, and a nonlinear flexible multi-body dynamics analysis code, DYMORE. Considering insufficient measurement data for HART II rotor, prescribed airloads computed by a three-dimensional compressible flow solver KFLOW are used to replace the lifting-line airloads and thereby enhance the prediction capability of the comprehensive analyses. The CSD results on blade elastic deflections using the prescribed airloads indicate more oscillatory behavior than those by lifting-line based approaches, but the wave pattern becomes improved by including artificial damping into the rotor system. It is demonstrated that the structural load predictions are improved significantly by the prescribed airloads approach against the measured data, as compared with an isolated CSD analysis.

• International Journal of Aeronautical and Space Sciences
• /
• 제10권2호
• /
• pp.52-62
• /
• 2009

A three-dimensional compressible Navier-Stokes solver, KFLOW, using overlapped grids has recently been developed to simulate unsteady flow phenomena over helicopter rotor blades. The blade-vortex interaction is predicted for a descending flight using measured blade deformation data. The effects of computational grid resolution and azimuth angle increments on airloads were examined, and computed airloads and vortex trajectories were compared with HART-II wind tunnel data. The current method predicts the BVI phenomena of blade airloads reasonably well. It is found from the present study that a peculiar distribution of vorticity of tip vortices in an approximate azimuth angle range of 90 to 180 degrees can be explained by physics of the shear-layer interaction as well as the dissipation of numerical schemes.

• 대한기계학회논문집B
• /
• 제29권12호
• /
• pp.1360-1368
• /
• 2005

This study investigates the characteristics of spray, such as evaporation rate and spray trajectory, for a 4-hole injector which is applied to a 4-valve motorcycle gasoline engine. Three dimensional, unsteady, compressible flow and spray within the intake-port and cylinder have been simulated using the VECTIS code. Spray characteristics were investigated at 6000 rpm engine speed. Furthermore, we visualized fuel behavior in the intake-port using a CCD camera synchronized with a stroboscope in order to compare with the analytical results. Boundary and intial conditions were employed by complete 1-D simulation of the engine using the WAVE code. Fuel was injected into the intake-port at two time intervals relative to the position of the intake valves so that the spray arrived when the valves were closed and fully open. The results showed that the trajectory of the spray was directed towards the lower wall of the port with injection against the closed valves. With open valve injection, a large portion of the fuel was lifted by the co-flowing air towards the upper half of the port and this was confirmed by simulation and visualization.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권1호
• /
• pp.8-19
• /
• 2016

This paper investigates the effects of inlet turbulence conditions and near-wall treatment methods on the heat transfer prediction of gas turbine vanes within the range of engine relevant turbulence conditions. The two near-wall treatment methods, the wall-function and low-Reynolds number method, were combined with the SST and ${\omega}RSM$ turbulence model. Additionally, the RNG $k-{\varepsilon}$, SSG RSM, and $SST_+{\gamma}-Re_{\theta}$ transition model were adopted for the purpose of comparison. All computations were conducted using a commercial CFD code, CFX, considering a three-dimensional, steady, compressible flow. The conjugate heat transfer method was applied to all simulation cases with internally cooled NASA turbine vanes. The CFD results at mid-span were compared with the measured data under different inlet turbulence conditions. In the SST solutions, on the pressure side, both the wall-function and low-Reynolds number method exhibited a reasonable agreement with the measured data. On the suction side, however, both wall-function and low-Reynolds number method failed to predict the variations of heat transfer coefficient and temperature caused by boundary layer flow transition. In the ${\omega}RSM$ results, the wall-function showed reasonable predictions for both the heat transfer coefficient and temperature variations including flow transition onset on suction side, but, low-Reynolds methods did not properly capture the variation of the heat transfer coefficient. The $SST_+{\gamma}-Re_{\theta}$ transition model showed variation of the heat transfer coefficient on the transition regions, but did not capture the proper transition onset location, and was found to be much more sensitive to the inlet turbulence length scale. Overall, the Reynolds stress model and wall function configuration showed the reasonable predictions in presented cases.

• 한국유체기계학회 논문집
• /
• 제17권6호
• /
• pp.52-58
• /
• 2014

In the present work, design optimization of film-cooling hole array on the pressure side of high pressure turbine nozzle was conducted. There are four rows of fan-shaped film cooling holes on the nozzle pressure side surface and each row has a straight array of holes in the spanwise direction for baseline model. For design optimization, hole distributions in streamwise and spanwise directions for three rows of holes except first row are parameterized as a 2nd-order shape function. Three-dimensional compressible RANS equations are used for flow and thermal analysis around the nozzle surface and optimization technique using Design of Experiment, Kriging surrogate model and Genetic Algorithm is used. The results shows that averaged adiabatic wall temperature at the whole nozzle surface decreases about 2.7% and averaged film cooling effectiveness at the pressure side of nozzle increased about 8.2%.

• 대한기계학회논문집B
• /
• 제35권9호
• /
• pp.903-913
• /
• 2011

본 연구에서는 가스터빈 블레이드의 냉각을 위해 사용되는 막냉각 홀을 대상으로 다양한 형상변수들이 막냉각 효율에 미치는 영향을 평가하기 위한 수치적 연구를 수행하였다. 삼차원 압축성 Reynolds-averaged Navier-Stokes 해석을 수행하였으며, 난류모델로는 shear stress transport 모델이 사용되었다. 해석을 통해 홀의 형상, 측면 방향 분사각, 홀의 주기 및 분사율이 막냉각 효율에 미치는 영향이 평가되었다. 해석결과, 원통형홀의 경우 측면 방향 분사각이 존재할 때 월등히 향상된 막냉각 효율을 보여주었으며, 홴형상 홀의 경우 측면 방향 분사각이 $20^{\circ}{\sim}30^{\circ}$일 때 가장 높은 막냉각 효율을 보여주었다. 또한 홀의 주기의 변화에 따른 성능평가 결과 높은 분사율일 때가 낮은 분사율의 경우보다 홀의 주기에 의존하는 경향을 보였다.

• 한국항공우주학회지
• /
• 제46권5호
• /
• pp.376-384
• /
• 2018

본 연구에서는 투과면을 이용하는 음향상사법으로 제자리 비행하는 UH-1H 로터 블레이드 주위의 원방 소음을 예측하였다. 두께 소음과 하중 소음, 그리고 충격파 및 끝단 후류 등에 의해 발생하는 유동 소음을 예측하기 위해 블레이드 표면을 포함하는 투과면을 구성하였다. 3차원 압축성 Euler 방정식 및 Navier-Stokes 방정식을 적용하여 공력 해석을 수행하고 비교하였다. 투과면의 위치에 따라 High Speed Impulsive 소음을 예측 및 검증하였다. 블레이드 끝단에서 발생하는 충격파에 의한 소음원이 지배적인 요소임을 확인하였으며, 충격파를 온전히 포함하도록 투과면을 구성하는 것이 중요함을 보였다.

• Advances in aircraft and spacecraft science
• /
• 제7권6호
• /
• pp.537-551
• /
• 2020

Investigation of leading edge impingement cooling for first stage rotor blades in an aero-engine turbine, its effect on rotor temperature and trailing edge wake loss have been undertaken in this study. The rotor is modeled with the nozzle for attaining a more accurate simulation. The rotor blade is hollowed in order for the coolant to move inside. Also, plenum with the 15 jet nozzles are placed in it. The plenum is fed by compressed fresh air at the rotor hub. Engine operational and real condition is exerted as boundary condition. Rotor is inspected in two states: in existence of cooling technique and non-cooling state. Three-dimensional compressible and steady solutions of RANS equations with SST K-ω turbulent model has been performed for this numerical simulation. The results show that leading edge is one of the most critical regions because of stagnation formation in those areas. Another high temperature region is rotor blade tip for existence of tip leakage in this area and jet impingement cooling can effectively cover these regions. The rotation impact of the jet velocity from hub to tip caused a tendency in coolant streamlines to move toward the rotor blade tip. In addition, by discharging used coolant air from the trailing edge and ejecting it to the turbines main flow by means of the slot in trailing edge, which could reduce the trailing edge wake loss and a total decrease in the blade cooling loss penalty.