• ETRI Journal
• /
• v.38 no.6
• /
• pp.1135-1144
• /
• 2016

Fractal antenna arrays are geometry-based thinned arrays having multiband applications. The major challenge of these arrays is their large number of elements at higher expansion factors. This article presents the thinning of fractal antenna arrays while maintaining an appropriate balance between the side lobe level and beam width by using various quantized fractal distribution functions. A 2D square fractal antenna array and 3DSierpinski gasket antenna array are considered in this article to validate the proposed distribution functions. Nearly one third of the antenna elements are thinned in each successive iteration except in the case of a one-count distribution function. The proposed technique can simplify practical implementation and exhibits better performance for various parameters such as the side lobe level, side lobe angle, and half power beam width than fully populated fractal antenna arrays.

• Nuclear Engineering and Technology
• /
• v.42 no.5
• /
• pp.546-551
• /
• 2010

The objective of this research is to estimate the crack location and size of a carbon steel pipe by using a laser ultrasound guided wave for the wall thinning evaluation of an elbow. The wall thinning of the carbon steel pipe is one of the most serious problems in nuclear power plants, especially the wall thinning of the carbon steel elbow caused by Flow-Accelerated Corrosion (FAC). Therefore, a non-destructive inspection method of elbow is essential for the nuclear power plants to operate safely. The specimens used in this study were carbon steel elbows, which represented the main elements of real nuclear power plants. The shape of the wall thinning was an oval with a width of 120mm, a length of 80mm, and a depth of 5mm. The L(0,1) and L(0,2) modes variation of the ultrasound guided wave signal is obtained from the response of the laser generation/air-coupled detection ultrasonic hybrid system represent the characteristics of the defect. The trends of these characteristics and signal processing were used to estimate the size and location of wall thinning.

• Corrosion Science and Technology
• /
• v.14 no.1
• /
• pp.1-11
• /
• 2015

Local wall thinning and integrity degradation caused by several mechanisms, such as flow accelerated corrosion (FAC), cavitation, flashing and/or liquid drop impingements, are a main concern in carbon steel piping systems of nuclear power plant in terms of safety and operability. Thinned pipe management program (TPMP) had been developed and optimized to reduce the possibility of unplanned shutdown and/or power reduction due to pipe failure caused by wall thinning in the secondary side piping system. This program also consists of several technical elements such as prediction of wear rate for each component, prioritization of components for inspection, thickness measurement, calculation of actual wear and wear rate for each component. Decision making is associated with replacement or continuous service for thinned pipe components. Establishment of long-term strategy based on diagnosis of plant condition regarding overall wall thinning is also essential part of the program. Prediction models of wall thinning caused by FAC had been established for 24 operating nuclear plants. Long term strategies to manage the thinned pipe component were prepared and applied to each unit, which was reflecting plant specific design, operation, and inspection history, so that the structural integrity of piping system can be maintained. An alternative integrity assessment criterion and a computer program for thinned piping items were developed for the first time in the world, which was directly applicable to the secondary piping system of nuclear power plant. The thinned pipe management program is applied to all domestic nuclear power plants as a standard procedure form so that it contributes to preventing an accident caused by FAC.

• Journal of the Korea Society of Computer and Information
• /
• v.15 no.10
• /
• pp.49-57
• /
• 2010

In this thesis, We studied on hand-written character recognition, that characters entered into a digital input device and remove noise and separating character elements using preprocessing. And processed character images has done thinning and 3-level wavelet transform for making normalized image and reducing image data. The structural method among the numerical Hangul recognition methods are suitable for recognition of printed or hand-written characters because it is usefull method deal with distortion. so that method are applied to separating elements and analysing texture. The results show that recognition by analysing texture is easily distinguished with respect to consonants. But hand-written characters are tend to decreasing successful recognition rate for the difficulty of extraction process of the starting point, of interconnection of each elements, of mis-recognition from vanishing at the thinning process, and complexity of character combinations. Some characters associated with the separation process is more complicated and sometime impossible to separating elements. However, analysis texture of the proposed character recognition with the exception of the complex handwritten is aware of the character.

• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.4
• /
• pp.7-16
• /
• 2002

En this paper, we propose the algorithm that has analyzed the map Information automatically to extract the contour lines and numbers, symbols from the map image. After converting the input image to binary one, thinned image is obtained by thinning algorithm. The contour elements in the thinned image are classified and the classified elements are analyzed to automatically classify the numbers from symbols. Finally, the broken parts are restored by reconstruction algorithm. The performance of proposed algorithm is verified through the simulation. The proposed one has good performance.

• 보존과학연구
• /
• s.7
• /
• pp.246-264
• /
• 1986

Micoromorphological alterations of sea-waterlogged woods by marinemicro-oragnisms were investigated by the light and scanning electron microscopy as a part of serial investigations on the shipwrecked materials which were excavated at the sea shore of Wando-Kun, southern coast of Korea in 1984.Deterioration of sea-waterlogged wood by marine microorganisms were varied with the wood species. The degree of deterioration even in the same wood specieswas different according to the part where it was in mud of sea-water. However, the resistance of Torreya nucifera over the marine organisms was marked. Deterioration in cell wall may be classified into three types; thinning of cell wall, separation of secondary wall from compound middle lamella and tunneling of cell wall. Thinning and separation were frequently observed, while the tunneling was rare. Among the wood cell elements of hardwoods, vessel wall was the least deteriorated. The difference degree of degradation of cell wall constituents and the accumulation of inorganic substances in cell lumen indicate that some factors to be considered for the conservation treatment were discussed. The kinds of marine microorganisms invading and/or inhabiting in wrecked wooden ship were also discussed.

• Corrosion Science and Technology
• /
• v.20 no.5
• /
• pp.242-248
• /
• 2021

Unforeseen failures of boilers in power plants may affect the continuation of electricity generation. Main failures in boilers are influenced by the tube material, tube position, boiler service temperature and pressure, and chemical composition of the feed water and coal. This investigation was intended to find answers on the causes and mechanism of failure of the fire-side boiler water-wall tubes, due to perforation and corrosion. The tube conformed to the material requirements in terms of its chemical composition and hardness. Microscopic examination showed ferrite and pearlite indicating no changes in its microstructure due to the temperature variation. SEM test showed a single layer and homogenous film density particularly on the area far from perforation. However, layers of corrosion product were formed on the nearby perforation area. EDX showed that there were Na, Ca, S, and O elements on the failed surface. XRD indicated the presence of Fe₂O₃ oxide. The failure mechanism was identified as a result of significant localized wall thinning of the boiler water wall-tube due to oxidation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.1
• /
• pp.74-84
• /
• 1988

This paper presents feature extraction technique for linear image using edge detection algorithms. The process of edge finding consists of determining edge magnitud and direction by convolution of an image with a number of edge masks, of thinning and ghresholding these edge magnitudes, of linking the edge elemtnts based on proximity ans orientation, and finally, of approximating the linked elements by piede-wise linear segmentss. These techniques are intened to be general and opplications to terminal detection and road recognition tasks are described. The presentation will be helpful to other researchers attempting to implement similar algorithms.

• Journal of the korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.48-59
• /
• 1990

A finite element program was developed using line elements for simulating the stretch/draw forming operation of an arbitrarily-shaped plane-strain section. An implicit, incremental, updated Lagrangian formulation is employed, introducing a minimum plastic work path assumption for each time step. Geometric and material nonlinearities are also considered within each time step. The finite element equation is based on the mesh-normal, which compatibly describes arbitrary tool surfaces and FEM meshes without depending on the explicit spatial derivatives of tool surfaces. The membrane approximation is adopted under the plane stress assumption. The sheet material is assumed to obey a rigid-viscoplastic constitutive law. The developed program was tested in the die-tryout of typical automotive inner panels. In order to determine a single friction coefficient and boundary length, FEM results and measurements of thinning for a stretched section of final die were compared. After finding analysis parameters, the sheet forming operations of original and final die designs were simulated. Excellent agreement between measured and computed thickness strains was obtained and the developed program was able to identify die designs which were rejected during die tryout.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.302-306
• /
• 1994

This paper describes how to recognize hand written Hangeul character using the stroke order of the elementary segment. The recognition system is constructed of parts : character input part, segment disassembling part, character element extraction part and character recognition part. The character input part reads the character and performs thinning algorithm. In the segment disassembling part, the input character is disassembled into elementary segments using the direction codes and the feature parameters. In the character element extraction part, we extract the character element using the stroke order and the knowledge rule. Finally, we able to recognize the hand written Hangeul characters by assembling the character elements, in the character recognition part.