• Steel and Composite Structures
• /
• 제14권2호
• /
• pp.105-120
• /
• 2013

Flexural behavior of thin walled steel-concrete composite sections as cross sections for beams is investigated by conducting an experimental study supported by applicable analytical predictions. The experimental study consists of testing up to failure, simply supported beams of effective span 1440 mm under two point loading. The test specimens consisted of composite box and channel (with lip placed on tension side and compression side) sections, the behavior of which was compared with companion empty sections. To understand the role of shear connectors in developing the composite action, some of the composite sections were provided with novel simple bar type and conventional bolt type shear connectors in the shear zone of beams. Two RCC beams having equivalent ultimate moment carrying capacities as that of composite channel and box sections were also considered in the study. The study showed that the strength to weight ratio of composite beams is much higher than RCC beams and ductility index is also more than RCC and empty beams. The analytical predictions were found to compare fairly well with the experimental results, thereby validating the applicability of rigid plastic theory to cold-formed steel concrete composite beams.

• Structural Engineering and Mechanics
• /
• 제46권3호
• /
• pp.323-335
• /
• 2013

This work aims to study the effect of stiffener ties in the behavior of intermediate length open section Cold-Formed Steel (CFS) Columns under axial compression. A comparative study on the behaviour and strength of Cold Formed Steel Columns by changing the direction of projection of lips (i.e., inwards or outwards) are also done. In this work two types of sections were considered Type-I section with lip projecting outwards (hat) and Type-II section with lip projecting inwards (channel). The length of the columns is predicted by performing elastic buckling analysis using CUFSM software. The theoretical analysis is performed using DSM - S100;2007, AS/NZ: 4600-2005 and IS: 801-1975. The compression tests are carried out in a 400 kN loading frame with hinged-hinged end condition. The non-linear numerical analysis is performed using Finite Element software ANSYS 12.0 to simulate the experimental results. Extensive parametric study is carried out by varying the width and spacing of the stiffener ties. The results are compared; the effects of stiffener ties on behaviour and load carrying capacity on both types of columns are discussed.

• Wind and Structures
• /
• 제15권3호
• /
• pp.189-208
• /
• 2012

Lock-in and drag amplification phenomena are studied for a flexible cantilever using a simplified fluid-structure interaction approach. Instead of solving the 3D domain, a simplified setup is devised, in which 2D flow problems are solved on a number of planes parallel to the wind direction and transversal to the structure. On such planes, the incompressible Navier-Stokes equations are solved to estimate the fluid action at different positions of the line-like structure. The fluid flow on each plane is coupled with the structural deformation at the corresponding position, affecting the dynamic behaviour of the system. An Arbitrary Lagrangian-Eulerian (ALE) approach is used to take in account the deformation of the domain, and a fractional-step scheme is used to solve the fluid field. The stabilization of incompressibility and convection is achieved through orthogonal quasi-static subscales, an approach that is believed to provide a first step towards turbulence modelling. In order to model the structural problem, a special one-dimensional element for thin walled cross-section beam is implemented. The standard second-order Bossak method is used for the time integration of the structural problem.

• International Journal of Aeronautical and Space Sciences
• /
• 제10권2호
• /
• pp.77-85
• /
• 2009

A two-dimensional cross-section analysis program based on the finite element method has been developed for composite blades with arbitrary cross-section profiles and material distributions. The modulus weighted approach is used to take into account the non-homogeneous material characteristics of advanced blades. The CLPT (Classical Lamination Plate Theory) is applied to obtain the effective moduli of the composite laminate. The location of shear center for any given cross-sections are determined according to the Trefftz' definition while the torsion constants are obtained using the St. Venant torsion theory. A series of benchmark examples for beams with various cross-sections are illustrated to show the accuracy of the developed cross-section analysis program. The cross section cases include thin-walled C-channel, I-beam, single-cell box, NACA0012 airfoil, and KARI small-scale blades. Overall, a reasonable correlation is obtained in comparison with experiments or finite element analysis results.

• Tuberculosis and Respiratory Diseases
• /
• 제39권1호
• /
• pp.103-108
• /
• 1992

Pulmonary paragonimiasis is the infectious disease of lung, due to 'Paragonimus westermani'. The clinical manifestations are various, and the main symptoms are chronic cough and persistent hemoptysis. Radiological findings mainly include thin walled cyst, migrating patch pulmonary infiltration, transient linear shadow, and hydropneumothorax, etc. The differential diagnosis should include pulmonary tuberculosis, pneumonia, other parasitic diseases, and rarely lung malignancy if the mass-like lesion is present. Recently, the incidence of paragonimiasis is very low. But the physicians should suspect paragonimus infection, if the patient has chronic respiratory symptom such as hemoptysis and lives in the endemic area such as Korea. A case of pulmonary paragonimiasis confirmed by histological basis of lung was presented with a review of the literature.

• Composites Research
• /
• 제17권4호
• /
• pp.25-31
• /
• 2004

본 연구에서는 다중세포로 구성된 타원형 단면 복합재료 블레이드의 정밀 1차원 보 해석모델을 개발하였다. 보의 정식화를 위하여 Reissner의 반보족에너지 함수를 이용하였으며, 고전적인 강성도 및 유연도법을 결합한 혼합보 이론 체계를 구축하였다. 타원단면의 특성계수들을 구하기 위해 단면의 외곽선을 유한개의 선분으로 분할하고 여기에 Gauss 적분을 수행하였다. 또한, 단면을 구성하는 각 세포에 대해 4개의 연속방정식이 충족되도록 구성하였다. 개발된 보 이론을 단일 및 이중세포로 구성된 타원형 복합재료 블레이드에 적용하였으며, 다차원 정밀 유한요소 해석 결과와 비교하여 그 타당성을 확보하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.768-776
• /
• 2007

In this study, axial vibration analysis has been conducted on a propulsion and lift shafting system for an air cushion vehicle using ANSYS code. The shafting system is totally flexible multi-elements system including wood composite material of air propeller. aluminum alloy of lift fan and thin walled shaft with flexible coupling. The analysis calculated the axial natural frequencies and mode shapes of the shafting system taking into account an equivalent mass-elastic model for shafting system as well as the three-dimensional models for propeller blade and fan impeller. Such a flexible shafting system has very intricate vibrating characteristics and especially, axial natural frequencies of flexible components such as propeller blade and impeller of lift fan can be lower to the extent that causes a resonance in the range of operating revolution. The results for axial vibration analysis are presented and compared with the results of axial vibration test for lift fan conducted during Sea Trial.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1549-1552
• /
• 2003

The front-end side members of automobiles absorb most of the energy in a front-end collision. The front-end side members are required to have a high stiffness together with easiness to collapse sequentially to absorb more impact energy. The axial static collapse test (5mm/mim) was conducted by using UTM with respect to the single hat shaped section members which are the standard section shape of the spot welded section members, to the single cap shaped section members, to the double cap shaped section members and to the double hat shaped section members whose section shape are changed in order to give more stiffness. As a result of test, the energy absorbing characteristic was analyzed for different section shapes. That is, it was analyzed that the change of section shape influenced the absorbing energy, the mean collapse load and the maximum collapse load, and that the relation between the change of section shape and the collapse mode.

• The Plant Pathology Journal
• /
• 제24권1호
• /
• pp.87-89
• /
• 2008

A blue mold on tomato fruit caused by Penicillium oxalicum occurred sporadically in a greenhouse at Gyeongsangnam-do Agricultural Research and Extension Services. Infection usually occurred through wounds or cracks on the fruits. Symptoms began with water soaking lesions, then became watery and softened eventually. Colony of the causal fungus was white at the early growing stage, turned green on Czapek yeast extract agar and malt extract agar. Conidia were ellipsoidal in shape and $2-6{\times}2-4{\mu}m$ in size. Stipes were septate, smooth, thin walled, and $90-280{\times}3-4{\mu}m$ in size. Penicilli were mostly biverticillate. Ramuli were 1-3 groups, smooth, and $10-16{\times}2-3{\mu}m$ in size. Rami were 1-2 groups and $6-30{\times}2-4{\mu}m$ in size. Metulae were 2-3(5) verticils, smooth, and $12-20{\times}3-4{\mu}m$ in size. Phialides were 5-7 verticilate, ampulliform to cylindroidal, smooth, and $8-12{\times}2-3{\mu}m$ in size. Optimum temperature for growth was about $25^{\circ}C$. Pathogenicity of the fungus was proved on tomato fruit according to Koch's postulation. On the basis of mycological and pathological characteristics, the fungus was identified as P. oxalicum Currie & Thom. This is the first report of the blue mold on tomato fruit caused by P. oxalicum in Korea.

• 한국공작기계학회논문집
• /
• 제16권4호
• /
• pp.113-118
• /
• 2007

The flow forming has been used to produce long thin walled tube parts, with the reduced fanning force and the enhanced mechanical and surface quality for a good finished part, compared with the fanned parts using other method. Therefore, flow fanning technique is used widely in industrial production. Spinning and flow fanning techniques are used frequently in automotive, aerial and defense industries. The main factors for the flow fanning machine design are motor power, bed rigidity, mandrel stiffness, spindle power, roller profile, etc. Especially, mandrel, spindle power and roller are important factors for flow fanning machine capacity. In this paper, three dimensional finite element method for analysis of one-roller backward flow fanning of a workpiece has been carried out to study effects of roller profile on fanning force. Applied roller profile have roller lead geometries of angle $20^{\circ},\;30^{\circ},\;40^{\circ}$, concave and convex. Axial and radial fanning forces on various roller profiles are obtained and compared with each analysis cases.