• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.168-171
• /
• 2005

Thickness optimization of heavily doped p-type seeding layer was studied to improve performance of thin film silicon solar cell. We used liquid phase epitaxy (LPE) to grow active layer of $25{\MU}m$ thickness on p+ seeding layer. The cells with p+ seeding layer of $10{\mu}m\;to\;50{\mu}m$ thickness were fabricated. The highest efficiency of a cell is $12.95\%$, with Voc=633mV, $Jsc=26.5mA/cm^2,\;FF=77.15\%$. The $P^+$ seeding layer of the cell is $20{\mu}m$, thick. As thicker seeding layer than $20{\mu}m$, the performance of the cell was degraded. The results demonstrate that the part of the recombination current is due to the heavily doped seeding layer. Thickness of heavily doped p-type seeding layer was optimized to $20{\mu}m$. The performance of solar cell is expected to improve with the incorporation of light trapping as texturing and AR coating.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.66-69
• /
• 2002

This paper presents deposition and characterizations of microcrystalline silicon$({\mu}c-Si:H)$ films prepared by hot wire chemical vapor deposition at substrate temperature below $300^{\circ}C$. The $SiH_{4}$ concentration$[F(SiH_{4})/F(SiH_{4})+F(H_{2})]$ is critical parameter for the formation of Si films with microcrystalline phase. At 6% of silane concentration, deposited intrinsic ${\mu}c-Si:H$ films shows sufficiently low dark conductivity and high photo sensitivity for solar cell applications. P-type ${\mu}c-Si:H$ films deposited by Hot-Wire CVD also shows good electrical properties by varying the rate of $B_{2}H_{6}$ to $SiH_{4}$ gas. The solar cells with structure of Al/nip ${\mu}c-Si:H$/TCO/glass was fabricated with single chamber Hot-Wire CVD. About 3% solar efficiency was obtained and applicability of HWCVD for thin film solar cells was proven in this research.

• 한국표면공학회지
• /
• 제46권2호
• /
• pp.61-67
• /
• 2013

Thin film solar cells have attracted much attention due to their high cell efficiency, comparatively low process cost, and applicability to flexible substrates. In particular, CIGS solar cells have been widely studied and produced because they demonstrated the highest cell efficiency. However, the deposition process of CIGS films generally includes the selenization process conducted at elevated temperature using toxic $H_2Se$ gas. To avoid this selenization process, CIGS thin films were, in this study, deposited by RF sputtering using single composite CIGS target. In addition, the effects of sputtering bias voltage and heat treatment on the microstructural and morphological changes in deposited CIGS films were investigated and discussed.

• 전기학회논문지
• /
• 제66권2호
• /
• pp.354-356
• /
• 2017

We focused on light management technology in amorphous silicon solar cells to suppress increase in absorber thickness for improving power conversion efficiency (PCE). $MgF_2$ and $TiO_2$ anti-reflection layers were coated on both sides of Asahi VU ($glass/SnO_2:F$) substrates, which contributed to increase in PCE from 9.16% to 9.81% at absorber thickness of only 150 nm. Also, we applied very thin $MgF_2$ as a rear reflector at n-type nanocrystalline silicon oxide/Ag interface to boost photocurrent. By reinforcing rear reflection, we could find the PCE increase from 10.08% up to 10.34% based on thin absorber about 200 nm.

• Current Photovoltaic Research
• /
• 제10권2호
• /
• pp.33-38
• /
• 2022

Planner configuration thin film solar cells (TFSCs) with SnS/CdS heterojunction performed a lower short-circuit current (J_SC). In this study, we have demonstrated a path to overcome deficiency in J_SC by the incorporation of Se in the SnS absorber. We carried out the incorporation of Se in VTD grown SnS absorber by rapid thermal annealing (RTA). The diffusion of Se is mostly governed by RTA temperature (T_RTA), also it is observed that film structure changes from cube-like to plate-like structure with T_RTA. The maximum J_SC of 23.1 mA cm^-2 was observed for 400℃ with an open-circuit voltage (V_OC) of 0.140 V for the same temperature. The highest performance of 2.21% with J_SC of 18.6 mA cm^-2, V_OC of 0.290 V, and fill factor (FF) of 40.9% is observed for a T_RTA of 300℃. In the end, we compare the device performance of Se- incorporated SnS absorber with pristine SnS absorber material, increment in J_SC is approximately 80% while a loss in V_OC of about 20% has been observed.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2000년도 제1회 신소재 심포지엄(차세대 광소재 심포지엄)
• /
• pp.37-51
• /
• 2000

This paper presented the trend of CIS solar cell development and the current status of CIS cell research conducted by the collaboration of KAIST and KIER.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.25-26
• /
• 2012

• 한국정밀공학회지
• /
• 제25권10호
• /
• pp.7-22
• /
• 2008

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.236-236
• /
• 2007

• 전자통신동향분석
• /
• 제24권4호
• /
• pp.135-146
• /
• 2009

박막 태양전지(Thin Film Solar Cells)는 기존의 결정질 실리콘 태양전지와는 달리 유리 등 저가의 기반을 활용하고 표면에 박막으로 실리콘 등 재료를 증축시킨 2세대 태양전지이다. 그동안 변환효율이 실리큰형보다 낮아 건물 외벽이나 기둥 등 일부 용도에만 사용이 국한되었다. 그러나 최근 들어 제조과정에 에너지가 적게 소모되어 짧은 기간 내에 투자비용을 회수할 수 있고, 소재비용도 대폭 줄일 수 있는 등 뛰어난 경제성으로 인해 태양전지 업체들이 투자를 늘리고 신규업체가 진입하는 등 박막 태양전지가 유망 태양전지 아이템으로 부상하고 있다.