• Korean Journal of Materials Research
• /
• v.19 no.2
• /
• pp.73-78
• /
• 2009

This study investigated the dependence of the various sputtering conditions (Ar pressure: $2{\sim}10\;mTorr$, Power: $50{\sim}150\;W$) and thickness ($50{\sim}1200\;nm$) of Si thin film on the electrochemical properties, microstructural properties and the capacity fading of a Si thin film anode. A Si layer and a Ti buffer layer were deposited on Copper foil by RF-magnetron sputtering. At 10 mTorr, the 50 W sample showed the best capacity of 3323 mAh/g, while the 100 W sample showed the best capacity retention of 91.7%, also at 10 mTorr. The initial capacities and capacity retention in the samples apart from the 50W sample at 10 mTorr were enhanced as the Ar pressure and power increased. This was considered to be related to the change of the microstructure and the surface morphology by various sputtering conditions. In addition, thinner Si film anodes showed better cycling performance. This phenomenon is caused by the structural stress and peeling off of the Si layer by the high volume change of Si during the charge/discharge process.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.4
• /
• pp.391-398
• /
• 2010

In this paper, we propose a sensor design by using a polysilicon strain gauge bonded to a metal diaphragm. The fabrication process of the thin polysilicon strain gauges having thicknesses of $50\;{\mu}m$ was established using conventional MEMS technologies; further, the technique of glass frit bonding of the polysilicon strain gauge to the stainless steel diaphragm was established. Performance of the polysilicon strain gauge bonded to the metal cantilever beam was evaluated. The gauge factor, temperature coefficient of resistance (TCR), nonlinearity, and hysteresis of the polysilicon strain gauge were measured. The results demonstrate that the resistance increases linearly with tensile stress, while it decreases with compressive stress. The value of the gauge factor, which represents the sensitivity of strain gauges, is 34.0; this value is about 7.15 times higher than the gauge factor of a metal-foil strain gauge. The resistance of the polysilicon strain gauge decreases linearly with an increase in the temperature, and TCR is $-328\;ppm/^{\circ}C$. Further, nonlinearity and hysteresis are 0.21 % FS and 0.17 % FS, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.245-245
• /
• 2009

l-D nanostructured materials have much more attention because of their outstanding properties and wide applicability in device fabrication. Copper oxide(CuO) has been realized as a p-type metal oxide semiconductor with narrow band gap of 1.2 -1.5eV. Copper oxide nanostructures can be synthesized by various growth method such as oxidation reaction, thermal evaporation thermal decomposition, sol-gel. and Mostly CuO nanowire prepared on the Cu substrate such as Copper foil, grid, plate. In this study, CuO NWs were grown by thermal oxidation (at various temperatures in air (1 atm)) of Cu metal deposited on CuO (20nm)/$SiO_2$(250nm)/Si. A 20nm-thick CuO layer was used as an adhesion layer between Cu metal and $SiO_2$

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.1
• /
• pp.187-190
• /
• 2012

Background: High incidence of gallbladder cancer (GBC) is reported from North India, with elevated concentrations of heavy metals in water and soil. This Indo-Japan collaborative study compared presence of heavy metals in gallbladder tissues. Methods: Heavy metal concentrations were estimated in Indian GBC and cholecystitis tissues and compared with Japanese GBC and cholecystitis tissues. Spectrophotometry was done for 13 Indian gallbladder tissues (8 GBC, 5 cholecystitis) and 9 Japanese (5 GBC, 4 cholecystitis). Transmission electron microscopy (TEM) thin foil element analysis was done in 10 Indian samples (6 GBC, 4 cholecystitis). Results: Chromium, lead, arsenic and zinc were significantly high in Indian GBC compared with Japanese GBC. Chromium, lead and arsenic were significantly high in the Indian cholecystitis tissues compared to the Japanese. TEM of Indian tissues demonstrated electron dense deposits in GBC. Conclusion: Heavy metals-chromium, lead, arsenic and zinc are potential carcinogens in Indian GBC from endemic areas. This preliminary study links presence of heavy metals in gallbladder cancer tissues in endemic areas.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.784-789
• /
• 1997

Aluminium solid electrolytic capacitor in which electroconducting polypyrrole(PPy) is used as an electrolyte is studied. Pyrrole(Py) is electrochemically synthesized using the etched and anodized aluminium foil electrode($Al_2O_3$) as an anode on which the thin layer of chemicalpolymerized PPy as a pre-coating layer is formed previously by chemical oxidative polymerization(CP). Investigating the effects of the polymerization conditions on the electrical characteristics of resulting capacitors, the capacitors which were obtained from the galvanostatic electrolysis of pyrrole containing sodium p-toluenesulfonate(TsONa) under the currents of $2.0{\sim}4.0mA/unit(6.5{\times}10mm)$, showed the most superior properties.

• Journal of Welding and Joining
• /
• v.21 no.2
• /
• pp.97-101
• /
• 2003

The change of microstructures in the base metal during transient liquid phase bonding process of directionally Ni base superalloy, GID-111 was investigated. Bonds were fabricated using a series of holding times(0~7.2ks) at three different temperatures. The flip chip bonding utilizing self-aligning characteristic of solder becomes mandatory to meet tolerances for the optical device. In this paper, a parametric study of aging condition and pad size of samples was evaluated. A TiW/Cu/electroplated Cu UBM structure was selected and the samples were aging treated to analyze the effect of intermetallic compounds with the time variations. An FIB technique was applied to the preparation of samples for TEM observations. An FIB technique is very useful to prepare TEM thin foil specimens from the solder joint interface. After aging treatment, the tendency to decrease in shear strength was measured and the structure of the solder and the UBM was observed by using SEM, TEM and EDS. As a result, the shear strength was decreased of about 21% in the 100${\mu}{\textrm}{m}$ sample at 17$0^{\circ}C$ aging compared with the maximum shear strength of the sample with the same pad size. In the case of the 12$0^{\circ}C$ aging treatment, 18% of decrease in shear strength was measured at the 100${\mu}{\textrm}{m}$ pad size sample. An intermetallic compound of Cu6Sn5 and Cu3Sn were also observed through the TEM measurement by using.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.194-202
• /
• 1996

Transmission electron microscopy has been used to characterize the dislocation structure in hot-pressed titanium diboride. The thin foil samples were prepared by the conventional ion beam thinning technique and reveal the main features associated with the dislocations ; low-angle grain boundaries with dislocation arrays, high-angle grain boundaries with ledges/steps on the boundary planes. The ledges/steps on the grain boundaries were characterized as the origin of defect structures such as dislocation formation or crack propagation near grain boundaries. A fraction of the high angle grain boundaries contained periodic arrays of grain boundary dislocations. The Burger's vectors of the dislocations in the $TiB_{2}$specimens were determined.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.3
• /
• pp.431-438
• /
• 1996

Transmission electron microscopy has been used to investigate the microstructure of hot-pressed $TiB_{2}$. Thin foil specimens, prepared by conventional ion beam thinning, revealed many features which originated from the crystallographic anisotropy of hexagonal $TiB_{2}$. It was observed that in these specimens Fe-impurities are precipitated to form secondary Fe-rich phases at grain triple edges, in grain boundaries and sometimes in-grain. These Fe-rich precipitates were characterised by their coherence or semi-coherence to a favourably oriented grain at a grain triple edge or grain boundaries or to the matrix $TiB_{2}$ phase.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.459-464
• /
• 2013

Structures can be evaluated their health status by allowable loading criteria. These criteria can be determined by the maximum strain. Therefore, in order to detect this maximum strain of structures, fiber optic Bragg grating(FBG) sensor probes are newly designed and fabricated to perform the memorizing detection even if the sensor system is on-and-off. The probe is constructed with an FBG optical fiber embedded in silver epoxy. When the load is applied and removed on the structure, the residual strain remains in the silver epoxy to memorize the maximum strain effect. In this study, a commercial Al-foil bonded FBG sensor probe was tested to investigate the detection feasibility at first. FBG sensor probes with silver epoxy were fabricated as three different sizes. The detection feasibility of maximum strain was studied by doing the tensile tests of CFRP specimens bonded with these FBG sensor probes. It was investigated the sensitivity coefficient defined as the maximum strain divided by the residual strain. The highest sensitivity was 0.078 of the thin probe having the thickness of 2 mm.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.285-288
• /
• 2007

박막형 태양전지 및 플렉서블 태양전지 기판으로 사용되는 금속기판의 우수성은 잘 알려져 있다. 그러나 상용 금속기판이 직면하고 있는 문제점을 보완하기 위해서 전주법으로 제조된 2원합금 금속포일을 개발하였으며, 박막형 및 플렉서블 태양전지의 기판재로 적용가능성을 확인하였다. 일반적으로 태양전지를 제조할 때 열 공정이 수행되며, 이때 기판재와 cell을 구성하는 반도체의 열팽창 계수 차이에 의한 열변형으로 결함이 발생될 수 있고, 태양전지 효율 및 수명을 저하시키는 원인이 될 수 있다. 이러한 원인이 될 수 있는 구성 재료간의 열팽창계수 차이에 의한 cell 의 변형량을 추정하기 위해 유한요소해석 방법을 사용하였다. 유한요소해석을 수행하기 위해 ALGOR 라는 해석 tool 을 사용하였다. 유한요소해석 수행에 사용된 상용 금속인 Mo, Ti, Al, SUS 포일과 전주법으로 제조된 2원합금 금속포일의 열팽창 계수는 실험을 통한 측정치이며, cell을 구성하는 반도체의 열팽창 계수와 열특성은 참고 문헌에 있는 자료들이다. 이 값들을 기반으로 cell 의 구성을 단순화시킨 가상의 태양전지가 제조 공정 온도에서 상온으로 냉각될 때의 열변형량을 계산하였다.