This study was to examine the drying characteristics of barley and the effect of moisture content of barley on milling performance. A barley variety, Jogang, having 35.0% of initial moisture content was used for this experiment. Thermo-hydrostatic dryer which consists of blower, condensor, heater, humidifier, drying chamber and control box, etc., was used for the drying experiment. The change in the weight of a barley sample was continuously measured by means of the ring type load cell installed inside the drying chamber. Milling test runs the samples having the predetermined moisture content were taken from each drying test run. A laboratory type barley miller was used for the milling test. The results of the study are summarized as follows: 1. The drying constants (k) applied for the thin layer drying model, (M-Me)/(Mo-Me) = $Ae^{-kt}$ were 0.155, 0.259 and 0.548, respectively, at the three levels of drying temperatures, $40^{\circ}C$, $50^{\circ}C$ and $60^{\circ}C$. The drying constants complied with the Arrhenius Equation, K = Ko exp (-C/T), were determined as $Ko=1.901455{\times}10^8$ and C = 6563. 2. The laboratory milling test indicated that the highest milled and head barley recovery was resulted from the sample which was dryed at $40^{\circ}C$. In general, the increase in the drying temperature from $40^{\circ}C$ to $60^{\circ}C$ indicated a negative effect on milling yields. 3. Also, the sample having 15% M.C. presented the highest milled and head barley recovery among the five moisture content levels (12, 15, 18,21 and 24%).
This study describes the first record of Bourgelatia diducta (Nematoda: Chabertiidae) from wild boars in the Republic of Korea (=South Korea). Gastrointestinal tracts of 87 Korean wild boars (Sus scrofa coreanus) hunted in mountains in the south-western part of South Korea between 2009 and 2012 were examined for their visceral helminths. B. diducta, as identified by morphological characteristics of the head and tail, were recovered from the large intestine of 47 (54%) wild boars. The average length of adult female worms was $11.3{\pm}0.872$ mm and the thickest part of the body measured $0.54{\pm}0.04$ mm in maximum width, while those of males were $9.8{\pm}0.72$ and $0.45{\pm}0.03$ mm, respectively. The characteristic J-shaped type II ovejector was observed in females, and the type II dorsal ray with 2 rami on each side of the median fissure was uniquely seen in males. The buccal capsule was small, relatively thin-walled, cylindrical, very short, and ring-shaped. The externodorsal ray arose from a common stem with the dorsal ray. The cervical groove was absent. The anterior extremity was equipped with 20-22 external corona radiata, 4 cephalic papillae and 2 lateral amphids around the mouth. The eggs were $66.0{\times}38.9{\mu}m$ in average size. By the present study, B. diducta (Nematoda: Chabertiidae) is recorded for the first time in South Korea. Additionally, morphological characteristics and identification keys provided in the present study will be helpful in the faunistic or taxonomic studies for strongylid nematodes related.
The Transactions of the Korean Institute of Electrical Engineers C
/
v.48
no.12
/
pp.761-767
/
1999
Poly-Si TFTs(polycrystalline silicon thin film transistors) fabricated on a low cost glass substrate have attracted a considerable amount of attention for pixel elements and peripheral driving circuits in AMLCS(active matrix liquid crystal display). In order to apply poly-Si TFTs for high resolution AMLCD, a high operating frequency and reliable circuit performances are desired. A new poly-Si TFT with CLBT(counter doped lateral body terminal) is proposed and fabricated to suppress kink effects and to improve the device stability. And this proposed device with BC(buried channel) is fabricated to increase ON-current and operating frequency. Although the troublesome LDD structure is not used in the proposed device, a low OFF-current is successfully obtained by removing the minority carrier through the CLBT. We have measured the dynamic properties of the poly-Si TFT device and its circuit. The reliability of the TFTs and their circuits after AC stress are also discussed in our paper. Our experimental results show that the BC enables the device to have high mobility and switching frequency (33MHz at $V_{DD}$ = 15 V). The minority carrier elimination of the CLBT suppresses kink effects and makes for superb dynamic reliability of the CMOS circuit. We have analyzed the mechanism in order to see why the ring oscillators do not operate by analyzing AC stressed device characteristics.
Many researcher's efforts have made a significant advancement of space frame structure with various portion, and it becomes the most outsanding one of space structures. However, with the characteristics of thin and long term of spacing, the unstable behavior of space structure is shown by initial imperfection, erection procedure or joint, especially space frame structure represents more. This kind of unstable problem could not be set up clearly and there is a huge difference between theory and experiment. Moreover, the discrete structure such as space frame has more complex solution, this it is not easy to derive the formulation of design about space structure. In this space frame structure, the character of rise-span ratio or load mode is represented by the instability of space frame structure with initial imperfection, and snap-through or bifurcation might be the main phenomenon. Therefore, in this study, space frame structure which has a lot of aesthetic effect and profitable for large space covering single layer is dealt. And because that the unstable behavior due to variation of inner force resistance in the elastic range is very important collapse mechanism, I would like to investigate unstable character as a nonlinear behavior with a geometric nonlinear. In order to study the instability. I derive tangent stiffness matrix using finite element method and with displacement incremental method perform nonlinear analysis of unit space structure, star dome and 3-ring star dome considering rise-span $ratio(\mu}$ and load $ratio(R_L)$ for analyzing unstable phenomenon.
Kim, ByongJin;Sim, KiDong;Hong, SeoungJoon;Moon, DaeHo;Son, YongHo;Kang, DaeByoung;Khim, JinYoung;Yoon, JuHoon
Journal of the Microelectronics and Packaging Society
/
v.23
no.4
/
pp.31-34
/
2016
System In Package (SiP) is getting popular and momentum for the recent wearable, IoT and connectivity application apart from mobile phone. This is driven by market demands of cost competitive, lighter and smaller/thinner and higher performance. As one of many semiconducting assembly products, Leadframe product has been widely used for low cost solution, light/ small and thin form factor. But It has not been applied for SiP although Leadframe product has many advantages in cost, size and reliability performance. SiP is mostly based on laminate substrate and technically difficult on Leadframe substrate because of a limitation in SMT performance. In this paper, Leadframe based SiP product has been evaluated about key technical challenges in SMT performance and electrical shield technology. Mostly Leadframe is considered not available to apply EMI shield because of tie-bar around package edge. In order to overcome two major challenges, connection bars were deployed properly for SMT pad to pad and additional back-side etching was implemented after molding process to achieve electrical isolation from outer shield coating. This product was confirmed assembly workability as well as reliability.
Kim, Hyeon-Min;Shin, Hi-Suk;Yoon, Joung-Won;Kim, Gab-Soon
Journal of Sensor Science and Technology
/
v.20
no.3
/
pp.172-177
/
2011
Finger patients can't use their hands because of the paralysis their fingers. Their fingers are recovered by rehabilitating training, and the rehabilitating extent can be judged by measuring the pressing force to be contacted with two fingers(thumb and first finger, thumb and middle finger, thumb and ring finger, thumb and little finger). At present, most hospitals have used a thin plastic-plate for measuring the two-finger grasping force, and we can only judge that they can grasp the plate with their two-finger through it, because the plate can't measure the two-finger grasping force. But, recently, the force measuring system for measuring two-finger grasping force was developed using three-axis force sensor, but it is very expensive, because it has a three-axis force sensor. In this paper, two-finger force measuring system with a one-axis force sensor which can measure two-finger grasping force was developed. The one-axis force sensor was designed and fabricated, and the force measuring device was designed and manufactured using DSP(Digital Signal Processing). Also, the grasping force test of men was performed using the developed two-finger force measuring system, it was confirmed that the grasping forces of men were different according to grasping methods, and the system can be used for measuring two-finger grasping force.
We grew the hexagonal GaN films on (100) Si and (00.1) sapphire substrates in the temperature range of $300~730^{\circ}C$ by the direct reaction between thermally ionized N-source and thermally evaporated Ga-source. The GaN growth rates are increased at the initial stage of GaN formation and it was saturated to some values by the coalescence of each crystallites. The oxygen signal was observed in XPS spectra for all the GaN films grown in this work, especially low- temperature grown GaN film may due to incorporation of the residual oxygen in the growth chamber. The surface of low-temperature and shorter time grown films covered only Ga-droplets. however, with increasing the both substrate temperature and the growth time GaN is growth to crystallites. and coalescence to ring-type crystallites. With sufficient supply of N-source, they were changed to platelets. In the PL spectrum measured at 20 K, we observed the impurity related emission at 3.32eV and 3.38eV.
Lespedeza species have been widely used not only as plant resources for bark, leaves and honey, but also as erosion control materials. This study was carried out to investigate the structural and wood tiber characteristics in order to obtain basic information for the utilization of the wood. The wood structure was investigated for 10 selected species and the wood fiber, for the 5 selected species among Lespedeza species distributed all over the country. The following results were obtained. In the cross section, campylotropis showed ray diffuse porous wood, L. bicolor, L. cyrtobotrya, L. thunbergii var. intermedia, diffuse porous wood, and L. tomentella, L. angustifolioides. L. maritima, L. robusta, L. patentibicolor, ring porous wood. The maximum diameter of a single vessel ranged 66-123 ${\mu}$ in all species. Campylotropis showed the most number of vessels, L. angustifolioides, the least. The number of ray per mm ranged 7-22, Campylotropis showed the most number of rays, L. angustifolioides, the least. In the radial section the average length of vessel ranged 121-250 ${\mu}$ in all species. L. thunbergii var. intermedia showed the longest vessel, L. tomentella, the shortest. In tangential section the average width of the uniseriate ray ranged 9.2-14.7${\mu}$, that of the multiseriate ray, 19.2-42.1 ${\mu}$. The average height of the uniseriate ray ranged 143.0-1162.0 ${\mu}$. The width of fiber ranged 10.12-13.61 ${\mu}$, L. maximowiezii showed the narrowest tiber, L. thunbergii var. intermedia. the widest, the thickness of fiber wall ranged 2.93-3.71 ${\mu}$ in the five species. L. maximowiezii showed the most thin fiber wall, L. thunbergii var. intermedia, the thickest, L. cyrtobotrya showed the difference in the size of fiber between the shade and the sunny sites but L. maximowiezii showed no difference. There was significant difference in fiber length, fiber width and wall thickness between L. eyrtobotrya and L. maximowiezii.
Proceedings of the Korean Vacuum Society Conference
/
2000.02a
/
pp.105-105
/
2000
현재 급격히발전하는 이동통신기술로 미루어 보아 앞으로는 모든 정보통신이 무선통신으로 이루어질 것이다. 그런데 무선통신은 이동성과 대용량의 정보전송에 초점을 맞추어 발전하고 있다. 많은 정보량을 전달하기 위해서 현재 사용되는 주파수 대역보다 고주파의 전파가 사용되어야 한다. 또한 이동성을 향상시키기 위해서는 통신기기의 소형화를 이루어야 하고 그러기 위해서 궁극적으로 모든 소자를 하나의 칩(chip)으로 집적화하는 것이 필요하다. 따라서 벌크상태로 사용되고 있는 유전체 공진기를 소형화, 즉 박막화해야만 한다. 결국 유전체 박막의 마이크로파 대역에서의 유전특성을 연구하고 그 특성을 향상시켜야만 한다. 통신기기에서 사용되는 유전체 공진기는 소형화를 위해 높은 유전율과 낮은 유전손실(tan$\delta$), 즉 높은 품질계수 (Q)를 가져야 한다. 마이크로파 대역에서 사용되고 있는 유전체 중에서 TiO2는 벌크 상태의 rutile 상에서 100정도의 높은 유전율과, 4 GHz에서 10,000 정도의 높은 품질계수를 나타낸다고 보고되어 있다. 따라서 본 연궁서는 TiO2 박막의 마이크로파 유전특성을 연구하였고 anatase 박막의 유전특성도 측정하였다. TiO2 박막을 RF magnetron reactive sputtering 방법으로 Ar (15 sccm)과 O2 (1.5 sccm) 기체를 사용하여 상온에서 증착하였다. 4mTorr의 증착압력에서 안정한 rutile 박막을 얻었고, 15 mTorrdo서 준안정한 anatase 박막을 얻을 수 있었다. 그리고 그 중간의 압력에서 두 상이 혼합된 박막이 증착되었다. 위와 같은 방법으로 형성한 TiO2 박막의 마이크로파 유전특성을 측정하기 위해 마이크로스트립 링공진기 (microstrip ring resonator)를 제작하였다. 마이크로스트립 링 공진기는 링의 원주길이가 전자기파 파장길이의 정수배가 되면 공진이 일어나는 구조이다. Fused quartz를 기판으로 하여 증착압력을 변수로 하여 TiO2 박막을 증착하였다. 그리고 그 위에 은 (silver)을 사용하여 링 패턴을 형성하였다. 이와 같이 공진기를 제작하여 network analyzer (HP 8510C)로 마이크로파 대역에서의 공진특서을 측정하였다. 공진특성으로부터 전체 품질계수와 유효유전율, 그리고 TiO2 박막의 품질계수를 얻어내었다. 측정결과 rutile에서 anatase로 박막의 상이 변할수록 유전율은 감소하고 유전손실은 증가하는 결과를 나타내었다.
Proceedings of the Korean Vacuum Society Conference
/
2010.02a
/
pp.435-435
/
2010
A inclined slot-excited plasma source is newly designed and constructed for higher flux HNB(Hyperthermal Neutral Beam) generation. The present source is different from the vertical SLAN(SLot ANtenna) sources [1] in two aspects. One is that the slots are inclined, and the other is that the magnetic field is configured to a cusp type. These modifications are intended to make the source plasma operated in sub-milli-torr pressure regime and as thin as possible, both of which is to get higher HNB flux by decreasing the re-ionization rate of the reflected atoms from the neutralizer [2]. The plasma is generated in a quartz tube of internal diameter 170 mm enclosed in a aluminum application chamber of larger diameter 250 mm. The microwave power is fed to the plasma chamber by 8 inclined slots cut into the application chamber wall. The slots are coupled the chamber to a WR280 waveguide wound around it to form a ring resonator. In order to make two slots $\lambda_g/2$ apart in phase, the adjacent slots are rotated in opposite directions. The rotation angle of the slots are set to $60^{\circ}$ from the chamber axis. Between the quartz chamber and the aluminum cylindrical chamber 8 NdFeB magnets are equally spaced and fixed to form the cusp magnetic field confinement and ECR (Electron Cyclotron Resonance) field. In this presentation, the magnetic and electromagnetic simulations, and the measured plasma parameters are given for both the inclined and the vertical slot-excited plasma sources. We also discuss how the sources can be tailored to suit better-performing HNB sources.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.