• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.50-56
• /
• 2011

In this study, the effects of ZnO buffer layer thickness and annealing temperature on the heterojunction diode, ZnO/b-ZnO/p-Si(111), were reported. The effects of those on the structural and electrical properties of zinc oxide (ZnO) films on ZnO buffered p-Si (111) substrate were also studied. Structural properties of ZnO thin films were studied by X-ray diffraction and I-V characteristics were measured by a semiconductor parameter analyzer. ZnO thin films with 70 nm thick buffer layer and annealing temperature of $700^{\circ}C$ showed the best c-axis preferred orientation. The best electrical property was found at the condition of buffer layer annealing temperature of $700^{\circ}C$ and 50nm thick ZnO buffer layer (resistivity: $2.58{\times}10^{-4}[{\Omega}-cm]$, carrier concentration: $1.16{\times}1020[cm^{-3}]$). The I-V characteristics for ZnO/b-ZnO/p-Si(111) heterojunction diode were improved with increasing buffer layer thickness at buffer layer annealing temperature of $700^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.248-255
• /
• 2020

The effects of the coating thickness on the thermal durability and thermal stability of thermal barrier coatings (TBCs) with a gradient coating thickness were investigated using a flame thermal fatigue (FTF) test and thermal shock (TS) test. The bond and topcoats were deposited on the Ni-based super-alloy (GTD-111) using an air plasma spray (APS) method with Ni-Cr based MCrAlY feedstock powder and yttria-stabilized zirconia (YSZ), respectively. After the FTF test at 1100 ℃ for 1429 cycles, the bond coat was oxidized partially and the thermally grown oxide (TGO) layer was observed at the interface between the topcoat and bond coat. On the other hand, the interface microstructure of each part in the TBC specimen showed a good condition without cracking or delamination. As a result of the TS test at 1100 ℃, the TBC with gradient coating thickness was initially delaminated at a thin part of the coating layer after 37 cycles, and the TBC was delaminated by more than 50% after 98 cycles. The TBCs of the thin part showed more oxidation of the bond coat with the delamination of topcoat than the thick part. The thick part of the TBC thickness showed good thermal stability and oxidation resistance of the bond coat due to the increased thermal barrier effect.

• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.12-16
• /
• 2012

Although silver is used for T-OLED (Top emitting organic Light-Emitting Diode) as reflective anode, it is not an ideal material due to its low work function. Thus, we study the effect of annealing and atmospheric pressure plasma treatment on Ag film that increases its work function by forming the thin silver oxide layer on its surface. In this study, we deposited silver on glass substrate using RF sputtering. Then we treated the Ag samples annealing at $300^{\circ}C$ for 30 minutes in atmosphere or treating the atmospheric plasma treatment for 30, 60, 90, 120s, respectively. We measured the change of the mechanical properties and the potential value of surface with each one at a different treatment type and time. We used nano-indenter system and KPFM (Kelvin Probe Force Microscopy). KPFM method can be measured the change of surface potential. The nanoindenter results showed that the plasma treatment samples for 30s, 120s had very low elastic modulus, hardness and Weibull modulus. However, annealed sample and plasma treated samples for 60s and 90s had better mechanical properties. Therefore, plasma treatment increases the uniformity thin film and the surface potential that is very effective for the performace of T-OLED.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.145-145
• /
• 2008

High-k materials have been paid much more attention for their characteristics with high permittivity to reduce the leakage current through the scaled gate oxide. Among the high-k materials, $ZrO_2$ is one of the most attractive ones combing such favorable properties as a high dielectric constant (k= 20 ~ 25), wide band gap (5 ~ 7 eV) as well as a close thermal expansion coefficient with Si that results in good thermal stability of the $ZrO_2$/Si structure. During the etching process, plasma etching has been widely used to define fine-line patterns, selectively remove materials over topography, planarize surfaces, and trip photoresist. About the high-k materials etching, the relation between the etch characteristics of high-k dielectric materials and plasma properties is required to be studied more to match standard processing procedure with low damaged removal process. Among several etching techniques, we chose the inductively coupled plasma (ICP) for high-density plasma, easy control of ion energy and flux, low ownership and simple structure. And the $BCl_3$ was included in the gas due to the effective extraction of oxygen in the form of $BCl_xO_y$ compounds. During the etching process, the wafer surface temperature is an important parameter, until now, there is less study on temperature parameter. In this study, the etch mechanism of $ZrO_2$ thin film was investigated in function of $Cl_2$ addition to $BCl_3$/Ar gas mixture ratio, RF power and DC-bias power based on substrate temperature increased from $10^{\circ}C$ to $80^{\circ}C$. The variations of relative volume densities for the particles were measured with optical emission spectroscopy (OES). The surface imagination was measured by scanning emission spectroscope (SEM). The chemical state of film was investigated using energy dispersive X-ray (EDX).

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.1
• /
• pp.45-50
• /
• 2014

Effects of wet chemical treatment and thermal cycle conditions on the quantitative interfacial adhesion energy of $Cu/SiN_x$ thin film interfaces were evaluated by 4-point bending test method. The test samples were cleaned by chemical treatment after Cu chemical-mechanical polishing (CMP). The thermal cycle test between Cu and $SiN_x$ capping layer was experimented at the temperature, -45 to $175^{\circ}C$ for 250 cycles. The measured interfacial adhesion energy increased from 10.57 to $14.87J/m^2$ after surface chemical treatment. After 250 thermal cycles, the interfacial adhesion energy decreased to $5.64J/m^2$ and $7.34J/m^2$ for without chemical treatment and with chemical treatment, respectively. The delaminated interfaces were confirmed as $Cu/SiN_x$ interface by using the scanning electron microscope and energy dispersive spectroscopy. From X-ray photoelectron spectroscopy analysis results, the relative Cu oxide amounts between $SiN_x$ and Cu decreased by chemical treatment and increased after thermal cycle. The thermal stress due to the mismatch of thermal expansion coefficient during thermal cycle seemed to weaken the $Cu/SiN_x$ interface adhesion, which led to increased CuO amounts at Cu film surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.348-348
• /
• 2014

차세대 디스플레이 구동 회로 소자를 위한 재료로서, Amorphous Oxide Semiconductor (AOS)가 주목받고 있다. AOS는 기존의 Amorphous Silicon과 비교하여 뛰어난 이동도를 가지고 있으며, 넓은 밴드 갭에 의한 투명한 광학적 특성을 가지고 있다. 이러한 장점을 이용하여, AOS 박막은 thin film transistor (TFT)의 active channel로 이용 되고 있다. 하지만, AOS를 이용한 TFT의 경우, 시간이 경과함에 따라 $O_2$ 및 $H_2O$ 흡착에 의해 전기적 특성이 변하는 현상이 있다. 이러한 현상은 소자의 신뢰성에 있어 중요한 문제가 된다. 이러한 문제를 연구하기 위해 본 논문에서는, AOS 박막을 이용하여 bottom 게이트형 TFT를 제작하였다. 이를 위해 먼저, p-type Si 위에 건식산화방식으로 $SiO_2$(100 nm)를 성장시켜 게이트 산화막으로 이용하였다. 그리고 Zn과 Sn이 1: 2의 조성비를 가진 ZnSnO (ZTO) 용액을 제조한 후, 게이트 산화막 위에 spin coating 하였다. Splin coating된 용액에 남아 있는 솔벤트를 제거하기 위해 10분 동안 $230^{\circ}C$로 열처리를 한 후, 포토리소그래피와 에칭 공정을 이용하여 ZTO active channel을 형성하였다. 그 후, 박막 내에 남아 있는 불순물을 제거하고 ZTO TFT의 전기적인 특성을 향상시키기 위하여, $600^{\circ}C$의 열처리를 30분 동안 진행 하여 junctionless형 TFT 제작을 완료 하였다. 제작된 소자의 시간 경과에 따른 열화를 확인하기 위하여, 대기 중에서 2시간마다 HP-4156B 장비를 이용하여 전기적인 특성을 확인 하였으며, 이러한 열화는 후처리 공정을 통하여 회복시킬 수 있었다. 열화의 회복을 위한 후처리 공정으로, 퍼니스를 이용한 고온에서의 열처리와 microwave를 이용하여 저온 처리를 이용하였다. 결과적으로, TFT는 소자가 제작된 이후, 시간에 경과함에 따라서 on/off ratio가 감소하여 열화되는 경향을 보여 주었다. 이러한 현상은, TFT 소자의 ZTO back-channel에 대기 중에 있는 $O_2$ 및 $H_2O$의 분자의 물리적인 흡착으로 인한 것으로 보인다. 그리고 추가적인 후처리 공정들에 통해서, 다시 on/off ratio가 회복 되는 현상을 확인 하였다. 이러한 추가적인 후처리 공정은, 열화된 소자에 퍼니스에 의한 고온에서의 장시간 열처리, microwave를 이용한 저온에서 장시간 열처리, 그리고 microwave를 이용한 저온에서의 단 시간 처리를 수행 하였으며, 모든 소자에서 성공적으로 열화 되었던 전기적 특성이 회복됨을 확인 할 수 있었다. 이러한 결과는, 저온임에도 불구하고, microwave를 이용함으로 인하여, 물리적으로 흡착된 $O_2$ 및 $H_2O$가 짧은 시간 안에 ZTO TFT의 back-channel로부터 탈착이 가능함과 동시에 소자의 특성을 회복 가능 함 의미한다.

• Applied Microscopy
• /
• v.42 no.2
• /
• pp.87-93
• /
• 2012

In this study, fine structures of silica, titanium dioxide, talc and kaolin used in decorative cosmetics and the mixture extracted from BB cream cosmetics were observed by scanning electron microscopy. Kaolin had plate like shape structures of polygon with smooth surface and edge of kaolin had a relatively smooth appearance in comparison with talc. Also, thickness of each layer was estimated to about $0.1{\mu}M$ in the lump formed in stratum of several layers. Talc was observed by lumps shape phase of layering very thin flake. Boundary of thin flake was sharp or angular phase and thickness of flake was approximately 600 nm in diameter. When comparing the thickness of kaolin and talc, we was confirmed that kaolin was thicker than talc. Diameter of titanium dioxide was estimated to 0.2~0.3 ${\mu}M$ and surface of particle was a soft cubic form. Silica was confirmed that variety of size from 200 nm to $15{\mu}M$ of globular shape was measured. From the observation of inorganic pigments, silica was homogeneous dispersed in the BB cream cosmetics and among each other was filled with relatively small size like talc, kaolin, titanium dioxide and iron oxide. In conclusion, we suggest that silica at decorative cosmetics were formed in cosmetic coat at the skin as the minimum thickness.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.31.1-31.1
• /
• 2009

Carbon nanotubes (CNTs) are attractive material because of their superior electrical, mechanical, and chemical properties. Furthermore, their geometric features such as a large aspect ratio and a small radius of curvature at tip make them ideal for low-voltage field emission devices including backlight units of liquid crystal display, lighting lamps, X-ray source, microwave amplifiers, electron microscopes, etc. In field emission devices for display applications, the phosphor anode is positioned against the CNT emitters. In most case, light generated from the phosphor by electron bombardment passes through the anode front plate to reach observers. However, light is produced in a narrow depth of the surface of the phosphor layer because phosphor particles are big as much as several micrometers, which means that it is necessary to transmit through the phosphor layer. Hence, a drop of light intensity is unavoidable during this process. In this study, we fabricated a transparent cathode back plate by depositing an ultra-thin film of single walled CNTs (SWCNTs) on an indium tin oxide (ITO)-coated glass substrate. Two types of phosphor anode plates were employed to our transparent cathode back plate: One is an ITO glass substrate with a phosphor layer and the other is a Cr-coated glass substrate with phosphor layer. For the former case, light was radiated from both the front and the back sides, where luminance on the back was ~30% higher than that on the front in our experiments. For the other case, however, light was emitted only from the cathode back side as the Cr layer on the anode glass rolled as a reflecting mirror, improving the light luminance as much as ~60% compared with that on the front of one. This study seems to be discussed about the morphologies and field emission characteristics of CNT emitters according to the experimental parameters in fabricating the lamps emitting light on the both sides or only on the cathode back side. The experimental procedures are as follows. First, a CNT aqueous solution was prepared by ultrasonically dispersing purified SWCNTs in deionized water with sodium dodecyl sulfate (SDS). A milliliter or even several tens of micro-liters of CNT solution was deposited onto a porous alumina membrane through vacuum filtration. Thereafter, the alumina membrane was solvated with the 3 M NaOH solution and the floating CNT film was easily transferred to an ITO glass substrate. It is required for CNT film to make standing CNTs up to serve as electron emitter through an adhesive roller activation.

• Korean Journal of Materials Research
• /
• v.2 no.5
• /
• pp.353-359
• /
• 1992

Thermal oxidation and plasma enhanced chemical vapor deposition of tantalum oxide thin films on p-type (100) Si substrates were studied to examine the dielectric nature of T$a_2O_5$ as a Al/T$a_2O_5$/p-Si capacitor. Microstructure and dielectric properties of the capacitors were investigated by XRD, AES, high frequency C-V analyzer, I-V meter and TEM. XRD analysis showed that the structure of T$a_2O_5$ films were amorphous, but the films were crystallized to hexagonal $\delta$-T$a_2O_5$ by 65$0^{\circ}C$ thermal oxidation treatment. It was found that the stoichiometry of the films was more or less close to 2 : 5. Leakage current density and relative dielectric constant of thermal oxidation T$a_2O_5$ film at 60$0^{\circ}C$ was 5.0${ imes}10^{-6}$/A/c$m^2 and 31.5, respectively. In the case of PECVD T$a_2O_5$film deposited at 0.47W/c$m^2 they were 2.5${ imes}10^{-5}$/A/$ extrm{cm}^2$ and 24.0, respectively. The morphology of the films and interfaces were investigated by TEM.

• Korean Journal of Materials Research
• /
• v.6 no.8
• /
• pp.779-785
• /
• 1996

Thin $700^{\circ}C$films were formed through layer inversion of Co/Nb bilayer during rapid thermal annealing(RTA). The Nb interlayer seems to effectively prevent over-consumption of Si and to control the silicidation reaction by forming Co-Nb intermetallic compounds and removing the native oxide formed on Si substrate which interferes the uniform Co-Si interaction. The final layer structure of the Co/Nb bilayer after $700^{\circ}C$ RTA was found to be ${Nb}_{2}{O}_{3}$/${Co}_{2}$Si.CoSi/${NbCo}_{x}$/Nb(O, C)/${CoSi}_{2}$/ Si. The layer inversion and the formation of a stable CoSi, phase occurred above $700^{\circ}C$, and the Nb silicides were not found at any annealing temperature. These may be due to the formation of very stable Co-Nb intermetallic compounds and Nb oxides which limit the moving of Co and Si.