• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권11호
• /
• pp.737-741
• /
• 2000

We fabricated resistive superconducting fault current limiters (SFCL) based on YBCO thin films grown on 2-inch diameter $Al_2O_3$ substrates. Two SFCLs with nearly identical properties were connected in series to investigate simultaneous quench. There was a slight difference in the rate of voltage increase between two SFCL units when they were operated independently. This difference resulted in significantly imbalanced power dissipation between the units. This imbalance was removed by connecting a shunt resister to an SFCL in parallel. The appropriate values of shunt resistance were 80 ${\Omega}$ at 75 $V_rms$ and 110 ${\Omega}$ at 120 $V_rms$, respectively. Increased power input at high voltages also reduced the initial imbalance in power dissipation, but with increase in film temperature to higher than 200 K.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.591-596
• /
• 2009

$TiN_xO_y/TiN_x$ multi-layer thin films with a high resistance(${\sim}k{\Omega}$) were deposited on $SiO_2/Si$ substrates at room temperature by sputtering. The $TiN_x$ thin films show island and smooth surface morphology in samples prepared by ${\alpha}$ and RF magnetron sputtering, respectively. $TiN_xO_y/TiN_x$ multi-layer in has been developed to control temperature coefficient of resistance(TCR) by the incorporation of $TiN_x$ layer(positive TCR) inserted into $TiN_xO_y$ layers(negative TCR). Electrical and structural properties of sputtered $TiN_xO_y/TiN_x$ multi-layer films were investigated as a function of annealing temperature. In order to achieve a stable high resistivity, multi-layer films were annealed at various temperatures in oxygen ambient. Samples annealed at $700^{\circ}C$ for 1 min exhibited good TCR value of approximately $-54 ppm/^{\circ}C$ and a stable high resistivity around $20k{\Omega}/sq$. with good reversibility.

• 센서학회지
• /
• 제26권6호
• /
• pp.438-444
• /
• 2017

In this paper, we focus on optimization of the in-situ phosphorous (P) doping of low-pressure chemical vapor deposited (LPCVD) poly Si resistors for obtaining near-zero temperature coefficient of resistance (TCR) at temperature range from 25 to $600^{\circ}C$. The deposited poly Si films were annealed by rapid thermal anneal (RTA) process at the temperature range from 900 to $1000^{\circ}C$ for 90s in nitrogen ambient to relieve intrinsic stress and decrease the TCR in the poly Si layer and get the Ohmic contact. After the RTA process, a roughness of the thin film was slightly changed but the grain size and crystallinity of the thin film with the increase in anneal temperature. The film annealed at $1,000^{\circ}C$ showed the behavior of Schottky contact and had dislocations in the films. Ohmic contact and TCR of $334.4{\pm}8.2$ (ppm/K) within 4 inch wafer were obtained in the measuring temperature range of 25 to $600^{\circ}C$ for the optimized 200 nm thick-poly Si film with width/length of $20{\mu}m/1,800{\mu}m$. This shows the potential of in-situ P doped LPCVD poly Si as a resistor for pressure sensor in harsh environment applications.

• 대한산업공학회지
• /
• 제19권3호
• /
• pp.113-121
• /
• 1993

The pressure distribution between body and seat surface has been considered as one of the most important factors which affect seation comfort. The pattern of body pressure distribution has been an index of measuring comfort of an automobile seat. There has been numerous studies that measured the body pressure distribution. But, studies have many problems(pressure distortion, resolution, reliability, portability, usability, and shape fitness) in measuring the body pressure distribution. In this study, the new body pressure distribution measuring equipment has been developed by using the thin, flat, and polymer-film devices known as Force Sensing Resistors(FSRs) in order to solve those problems.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2008년도 춘계학술대회 논문집
• /
• pp.332-334
• /
• 2008

The matrix-type superconducting fault current limiter (SFCL) using YBCO thin film consists of the trigger and current-limiting parts. We fabricated the matrix-type SFCL with the integrated current limiting modules. we carried out the experiment of matrix-type SFCL with the integrated current limiting modules connected in series or parallel. We saw current characteristics due to ratio of change the shunt resistance and turns. We confirmed that the difference of critical current between superconducting units was decreased by increment of current flowing into the reactor which applied the magnetic field into the superconducting units..

• 한국전자파학회논문지
• /
• 제13권1호
• /
• pp.7-11
• /
• 2002

본 논문에서는 저지대역에서 하모닉과 불요특성을 효과적으로 제거하기 위한 목적으로 박막 혹은 후박 저항을 이용한 새로운 형태의 마이크로스트립 형태의 저역통과 필터를 제안한다. 제안한 필터는 기존의 마이크로스트림형태의 저역통과 필터에 비해 20dB 이상의 불요파 제거 효과를 보인다. 설계된 저역통과 필터는 Ku 대역 위성중계기용 국부발진기의 하모닉 제거 필터로 사용되어질 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.45-45
• /
• 2007

Capacitors among the embedded passive components are most widely studied because they are the major components in terms of size and number and hard to embed compared with resistors and inductors due to the more complicated structure. To fabricate a capacitor-embedded PCB for in-line process, it is essential to adopt a low temperature process (<$200^{\circ}C$). However, high dielectric materials such as ferroelectrics show a low permittivity and a high dielectric loss when they are processed at low temperatures. To solve these contradicting problems, we studied BMN materials as a candidate for dielectric capacitors. processed at PCB-compatible temperatures. The morphologies of BMN thin films were investigated by AFM and SEM equipment. The electric properties (C-F, I-V) of Pt/BMN/Cu/polymer were evaluated using an impedance analysis (HP 4194A) and semiconductor parameter analyzer (HP4156A). $Bi_2Mg_{2/3}Nb_{4/3}O_7$(BMN) thin films deposited on copper clad laminate substrates by sputtering system as a function of Ar/$O_2$ flow rate at room temperature showed smooth surface morphologies having root mean square roughness of approximately 5.0 nm. 200-nm-thick films deposited at RT exhibit a dielectric constant of 40, a capacitance density of approximately $150\;nF/cm^2$, and breakdown voltage above 6 V. The crystallinity of the BMN thin films was studied by TEM and XRD. BMN thin film capacitors are expected to be promising candidates as embedded capacitors for printed circuit board (PCB).

• 대한전자공학회논문지TE
• /
• 제42권4호
• /
• pp.1-6
• /
• 2005

최근 저항이나 캐패시터와 같은 수동소자를 PCB의 내층에 제조하는 임베디드 패시브 기술이 고성능의 IT 제품을 제조하는데 사용되고 있다. 그런데 임베디드 캐패시터는 정전용량 밀도가 낮아 회로소자로서의 전반적인 응용에 한계가 있다. 본 논문에서는 이러한 한계를 극복하기 위하여 wrinkle형의 전극과 유전체 층을 가진 새로운 임베디드 캐패시터를 제안하였다. FEM 기법을 사용하여 wrinkle형 임베디드 캐패시터의 정전용량 밀도를 평가하였다. Wrinkle형 임베디드 캐패시터는 기존의 평면형 임베디드 캐패시터에 비하여 25.6%$\sim$39.6% 정도 큰 정전용량 밀도를 나타내었다. 특히, thin film형 임베디드 캐패시터에 wrinkle 구조를 적용할 때 정전용량 밀도가 보다 많이 향상되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.64-65
• /
• 2005

The structural and electrical properties of the films are investigated as a function of nitrogen/argon ratio at room temperature and at various deposition temperatures. The phase changes as $Ta_2N$ or TaN in the films were observed as nitrogen/argon ratio increases from 3% to 25%. The phase changes were associated with a change in the resistivity and TCR (temperature coefficient of resistance) of the films. TCR values of the films deposited at room temperature and different nitrogen contents were negative, and strongly decreased with the increase in nitrogen/argon ratio. The Ta2N films deposited at nitrogen/argon ratio of 3% show improved TCR values and thermal stability with increasing deposition temperature. The $Ta_2N$ films grown at nitrogen/argon ratio of 3% and the temperature of $200^{\circ}C$ showed a TCR value of -47 $ppm/^{\circ}C$, which is close to near-zero TCR in the range of deposition temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.36-37
• /
• 2006

Titanium oxy-nitride ($TiN_O_y$) thin films were deposited on $SiO_2$/Si substrates using reactive dc magnetron sputtering, and were then annealed at various temperatures in air ambient to incorporate oxygen into the films. The effect of annealing temperature on the structural and electrical properties of the films was investigated. The grain size of the films decreases with increasing annealing temperature. On the other hand, crystallinity of the films is independent of annealing temperature in air ambient. Resistivity of the films increases remarkably as an annealing temperature increases and temperature coefficience of resistance (TCR) of the films varies from a positive value to a negative value. The films annealed at $350^{\circ}C$ for 30 min exhibited a near-zero TCR value of approximately -5 ppm/K. The decrease of the grain size with increasing annealing temperature was attributed to an increase of oxygen concentration incorporated into the films during anncaling treatment.