• Journal of the Semiconductor & Display Technology
• /
• v.14 no.1
• /
• pp.61-65
• /
• 2015

We have fabricated poly(3,4-ethylenedioxythiophene) : poly(4-styrenesulfonate) (PEDOT : PSS) thin films using a slotdie coater for the applications of OLED lightings. It is demonstrated that the properties of slot-die coated PEDOT : PSS films are comparable with those of spin-coated ones. Namely, the average and peak-to-peak roughness of the slot-die coated 50-nm-thick PEDOT : PSS film are measured to be as low as 0.247 nm and 1.3 nm, respectively. Moreover, we have obtained excellent thickness uniformity (~1.91%). With the slot-die coated PEDOT : PSS films, we have fabricated green phosphorescent OLED devices. For comparison, we have also fabricated OLED devices with spin-coated PEDOT : PSS films. Both show almost no discrepancy in device performance. The power efficiency (25.4 lm/W) and emission uniformity (77%) of OLEDs with slot-die coated PEDOT : PSS films are shown to be slightly lower than those (27.3 lm/W, 80%) of OLEDs with spin-coated PEDOT : PSS films at the luminance of 1,000nit, increasing the feasibility of using a slot-die coating process for the fabrication of large-area OLED lighting sources at a competitive price.

• Journal of Sensor Science and Technology
• /
• v.5 no.2
• /
• pp.15-20
• /
• 1996

The diffusion of hydrogen ions into a sensing membrane causes the output voltage of pH-ISFET to vary with time, which might be considered to be drift in this sensor. We tried to deposit ultra-thin film for minimizing tile drift that has been considered to be main obstacle for putting pH-ISFET to practical use. In this paper, tantalum pentoxide, known as a good pH sensing membrane, was formed to about $70{\AA}$ thick by sol-gel method on $Si_{3}N_{4}/SiO_{2}$-gate of pH-ISFET. The fabricated $Ta_{2}O_{5}$-gate pH-ISFET showed good sensitivity(about 59mV/ pH) and good lineality in the range of pH $3{\sim}11$, and had relatively small average pH drift of about 0.06 pH/day.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.11
• /
• pp.50-58
• /
• 2000

A Mach-Zehnder type $Ti:LiNbO_3$ optical modulator with a grooved $SiO_2$ buffer layer, was evaluated in terms of an electrode structure. The finite element method was performed to find out the optinum design parameters of electrodes. characteristic impedance ($Z_o$), MW effective index ($N_{eff}$) and attenuation constant ($a_o$)of fabricated traveling-wave electrodes were measured and compared with those obtained by the simulation expectation. For an optical modulator with 11${\mu}m$thick electrodes and a grooved $SiO_2$ buffer layer, the 3dB bandwidth based on the RF measurement results turned out to be 18GHz.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.12
• /
• pp.89-100
• /
• 1997

This paper investigated a new type of low voltage threshold switch (LVTS). As distinguished from the many other types of electronic threshold switches, the LvTS is ; voltage controlled, occurs at low voltages ($V_{2}$ $O_{5}$lV devices. The average low threshold voltage < $V_{LVT}$>=218 mV (standard deviation =24mV~kT/q, where T=300K), and was independent of the device area (x100) and amorphous oxide occurred in an ~22.angs. thick interphase of the V/amorphous- $V_{2}$ $O_{5}$ contacts. At $V_{LVT}$ there was a transition from an initially low conductance (OFF) state into a succession of quantized states of higher conductance (ON). The OFF state was spatically homogeneous and dominated by tunneling into the interphase. The ON state conductances were consistent with the quantized conductances of ballistic transport through a one dimensional, quantum point contact. The temeprature dependence of $V_{LVT}$, and fit of the material parameters (dielectric function, barrier energy, conductivity) to the data, showed that transport in the OFF and ON states occurred in an interphase with the characteristics of, respectively, semiconducting and metallic V $O_{2}$. The experimental results suggest that the LVTS is likely to be observed in interphases produced by a critical event associated with an inelastic transfer of energy.rgy.y.rgy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.193-193
• /
• 2011

To obtain ceramic films, the sol-gel coating technique has been broadly used with heat treatment, but crack formation tend to occur during heat treatment in thick sol-gel films. We prepared PZT thin films by sol-gel method with single-step spin coating process. The PZT solution have been synthesized using lead acetate ($Pb(CH_3COO)_2$), zirconium acetylacetonate ($Zr(OC_3H_7^n)_4$), and titanium diisopropoxide bis(acetylacetonate) 75wt% in isopropanol ($Ti(OC_3H_7^i)_2(OC_3H_7^n)_2$) as starting materials and n-propanol was selected as a solvent. The poly(vynilpyrrolidone) (PVP) was added with 0, 0.25, 0.5, 0.75, and 1 molar ratios to control viscosity of solution. We investigated influence of the viscosity on thickness, microstructure, and electrical properties of final PZT films. Thermo-gravimetric analysis and differential scanning calorimeter (TGA/DSC) was carried out from room temperature to $800^{\circ}C$ in order to measure pyrolysis temperature. Structural characteristics were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Ferroelectric and dielectric properties were measured by RT66A (Radiant) and impedance analyzer (Agilent), respectively. The thicknesses of PZT films depended on incorporation of an excess amount of PVP. Finally, we obtained PZT films of good quality without crack formation via single-step spin coating.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.5
• /
• pp.230-234
• /
• 2014

IGZO/Ag bi-layered films were deposited on glass substrate at room temperature with radio frequency and direct current magnetron sputtering, respectively to consider the effect of Ag buffer layer on the electrical, optical and structural properties. For all deposition, while the thickness of Ag buffer layer was varied as 10, 15, and 20 nm, The thickness of IGZO films were kept at 100 nm, In a comparison of figure of merit, IGZO films with 15 nm thick Ag buffer layer show the higher figure of merit ($1.1{\times}10^{-2}{\Omega}^{-1}$) than that of the IGZO single layer films ($3.7{\times}10^{-4}{\Omega}^{-1}$). From the observed results, it is supposed that the IGZO 100 nm/Ag 15 nm bi-layered films may be an alternative candidate for transparent electrode in a transparent thin film transistor device.

• Journal of Surface Science and Engineering
• /
• v.42 no.3
• /
• pp.128-132
• /
• 2009

Transparent conducting thin films of indium tin oxide(ITO) co-sputtered with aluminum-doped zinc oxide(AZO) were deposited on glass substrate by dual magnetron sputtering. It was found that the electrical properties and structural characteristics of the films are significantly changed according to the sputtering power of the AZO target. The IAZTO film prepared with D.C power of ITO at 100 W and R.F power of AZO at 50 W shows an electrical resistivity of $4.6{\times}10^{-4}{\Omega}{\cdot}cm$ and a sheet resistance of $30{\Omega}/{\square}$ (for 150 nm thick). Besides of the improvement of the electrical properties, compared to the ITO films deposited at the same process conditions, the IAZTO films have very smooth surface, which is due to the amorphous nature of the films. However, the electrical conductivity of the IAZTO films was found to be deteriorated along with the crystallization in case of the high temperature deposition (above $310^{\circ}C$). In this work, high quality amorphous transparent conductive oxide layers could be obtained by mixing AZO with ITO, indicating possible use of IAZTO films as the transparent electrodes in OLED and flexible display devices.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.175-180
• /
• 2009

Multilayer ceramic capacitors (MLCCs) have continually been made smaller in size and larger in capacity in resent years. However, the end termination electrode is still thick in many MLCCs. In this study, we used small grain glass frit to embody thin film and highly densification in the end termination by improve sintering driving force with well-dispersion and rising surface energy. Pastes were fabricated using size changed glass frit, such as 0.1 ${\mu}m$, 0.5 ${\mu}m$, 1.0 ${\mu}m$, 4.0 ${\mu}m$. Fabricated pastes were applied 05A475KQ5 chip and fired various sintering temperatures to analyze sintering behavior of pastes. Consequently, small glass frit used pastes have many merits than larger, such as well-dispersion, improve cornercoverage and surface roughness, possibility of low temperature sintering. However, we confirmed that small glass frit used pastes have narrow sintering window by rapid completion of sintering densification.

• Journal of the Korean Magnetics Society
• /
• v.22 no.5
• /
• pp.162-166
• /
• 2012

V-I characteristics of Fe(100)/MgO(100)/Cu-phthalocyanine (CuPc)/Co hybrid magnetic tunnel junctions were investigated at different temperatures. Fe(100) and Co ferromagnetic layers were separated by an organic-inorganic hybrid barrier consisting of different thickness of CuPc thin film grown on a 2 nm thick epitaxial MgO(100) layer. As the CuPc thickness increases from 0 to 10 nm, a bistable switching behavior due to strong charging effects was observed, while a very large magenetoresistance was shown at 77 K for the junctions without the CuPc barrier. This switching behavior decreases with the increase in temperature, and finally disappears beyond 240 K. In this work, high-potential future applications of the MgO(100)/CuPc bilayer were discussed for hybrid spintronic devices as well as polymer random access memories (PoRAMs).

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.4
• /
• pp.67-72
• /
• 1989

Room Temperature Plasma Nitridation of silicon was investigated as a new LOCOS (local oxidation of silicon) process in order to reduce the bird's beak length. In $N_2$ plasma formed by 100kHz, 400W AC power, a thin silicon nitride film (<100${\AA}$) was uniformly grown on a silicon substrate. SEM studies showed that the nitride layer formed by this method can effectively protect the silicon from oxidation and reduce the bird's beak length to $0.2{mu}m$ when 4000${\AA}$ field oxide is grown. This is a considerable improvement comparing with 0.7${mu}m,$ the bird's beak, for the conventional LOCOS process using a thick LPCVD nitride. No appreciable crystalline defect could be found around the bird's beak with SEM cross-section afrer Secco etch. Leakage current tests were carried out on the $N^+/P^-$ well and $P^+/N^-$ well diodes formed by this new LOCOS process. The electrical tests indicate that this new process has electrical properties similar or superior to those of the conventional LOCOS process.