• Journal of Welding and Joining
• /
• 제31권5호
• /
• pp.47-53
• /
• 2013

We have investigated the traits of clad metals in hot-rolled clad steel plates, including the sensitization and mechanical properties of STS 316 steel plate and carbon steel (A516), under various specific circumstances regarding post heat treatment, multilayered welds, and thick or repeated welds for repair. For evaluations, sectioned weldments and external surfaces were investigated to reveal the degree of sensitization by micro vickers hardness, tensile, and etching tests the results were compared with those of EPR tests. The clad steel plates were butt-welded using FCAW and SAW with the time of heat treatment as the variable, a that was conducted at $625^{\circ}C$, for 80, 160, 320, 640, and 1280 min. Then, the change in corrosion resistance was evaluated in these specimens. With carbon steel (A516), as the heat treatment time increased, the annealing effect caused the tensile strength to decrease. The micro-hardness gradually increased and decreased after 640 min. The elongation and contraction of the area also increased gradually. The oxalic acid etch test and EPR test on STS316 and the clad metal showed STEP structure and no sensitization. From the test results on multi-layered and repair welds, it could be concluded that there is no effect on the corrosion resistance of clad metals. The purpose of this study was to suggest some considerations for developing on-site techniques to evaluate the sensitization of stainless steels.

• 한국재료학회지
• /
• 제29권8호
• /
• pp.497-504
• /
• 2019

In this study, the correlation between microstructure and Charpy impact properties of FCAW(Flux cored arc welding) HAZ(Heat affected zone) of thick steel plates for offshore platforms was investigated. The 1/4 thickness(1/4t) location HAZ specimen had a higher volume fraction of bainite and finer grain size of acicular ferrite than those of the 1/2 thickness (1/2t) location HAZ specimen because of the post heat effect during the continuous FCAW process. The Charpy impact energy at $-20^{\circ}C$ of the 1/4t location HAZ specimen was lower than that of the 1/2t location HAZ specimen because of the high volume fraction of coarse bainite. The Charpy impact energy at -40 and $-60^{\circ}C$ of the 1/2t location HAZ specimen were higher than those of the 1/2t location HAZ specimen because the ductile fracture occurred in the fine acicular ferrite and martensite regions. In the ductile fracture mode, the deformed regions were observed in fine acicular ferrite and martensite regions. In the brittle fracture mode, long crack propagation path was observed in bainite regions.

• Structural Engineering and Mechanics
• /
• 제60권4호
• /
• pp.567-594
• /
• 2016

The main objective of the current research is estimating the flexural behavior of ferrocement Ribbed Plates reinforced with composite material. Experimental investigation was carried out on fifteen plates; their dimensions were kept constant at 1200 mm in length, 600 mm width and 100 mm thick but with different volume fraction of steel reinforcement and number of ribs. Test specimens were tested until failure under three line loadings with simply supported conditions over a span of 1100 mm. Cracking patterns, tensile and compressive strains, deformation characteristics, ductility ratio, and energy absorption properties were observed and measured at all stages of loadings. Experimental results were compared to analytical models using ANSYS 10 program. Parametric study is presented to look at the variables that can mainly affect the mechanical behaviors of the model such as the change of plate length. The results showed that the ultimate strength, ductility ratio and energy absorption properties of the proposed ribbed plates are affected by the volume fraction and the type of reinforcement, and also proved the effectiveness of expanded metal mesh and woven steel mesh in reinforcing the ribbed ferrocement plates. In addition, the developed ribbed ferrocement plates have high strength, ductility ratio and energy absorption properties and are lighter in weight compared to the conventional RC ribbed plates, which could be useful for developed and developing countries alike. The Finite Element (FE) simulations gave good results comparing with the experimental results.

• Journal of Magnetics
• /
• 제20권3호
• /
• pp.312-316
• /
• 2015

Unlike conventional Eddy Current Test (ECT), Pulsed Eddy Current (PEC) uses a multiple-frequency current pulse through the excitation coil. In the present study, the detection of subsurface cracks using a specially designed probe that allows the detection of a deeper crack with a relatively small current density has been attempted using the PEC technique. The tested sample is a piece of 304 stainless steel (SS304) with a thickness of 30mm. Small electrical discharge machining (EDM) notches were put in the test sample at different depths from the surface to simulate the subsurface cracks in a pipe. The designed PEC probe consists of an excitation coil and a Hall sensor and can detect a subsurface crack as narrow and shallow as 0.2 mm wide and 2 mm deep. The maximum distance between the probe and the defect is 28 mm. The peak amplitude of the detected pulse is used to evaluate the cracks under the sample surface. In time domain analysis, the greater the crack depth the greater the peak amplitude of the detected pulse. The experimental results indicated that the proposed system has the potential to detect the subsurface cracks in stainless steel plates.

• 한국강구조학회 논문집
• /
• 제25권4호
• /
• pp.431-440
• /
• 2013

본 연구에서는 HSA800 후판 강재에 적합한 용접재를 선정하고자 표준인장실험을 수행하였다. 본 연구 수행 당시 HSA800 강재에 적용가능한 용접재로 GMAW 용접재(외국산)와 FCAW 용접재(국내산) 두 가지가 추천되어 이들을 사용하였다. 맞댐용접상세와 루트간격을 주요 실험변수로하여 표준인장실험을 통해 용접부의 성능을 평가하였다. 강도에 대한 설계요구조건은 두 용접재 모두 만족하였으나 연성능력 측면에서 GMAW 용접재 보다는 FCAW 용접재가 일관되고 우수한 거동을 보임이 실험적으로 확인되었다. 특히 GMAW 용접재는 용접효율과 작업성의 문제로 현장에서의 상향용접이 어려운 것으로 파악되었다. 같은 완전용입용접이라도 Single bevel보다는 V-groove가 안정적인 구조거동을 보이는 것으로 나타났다. 또한 현행 용접기준의 표준루트 간격을 벗어날 경우 용착의 어려움으로 비정상 파단면이 형성되고 접합성능도 저하됨이 확인되었다. 부분용입용접 접합부의 실험결과에 의할 때 현행 AISC 기준의 부분용입용접부 강도규정은 매우 보수적임이 확인되었다.

• 한국강구조학회 논문집
• /
• 제12권6호
• /
• pp.749-758
• /
• 2000

본 연구는 지그재그모델에 근거하여 두꺼운 금속, 폴리머 복합재료 면재의 전단변형 효과를 고려해서 샌드위치평판의 휨해석 지배방정식을 유도하였으며, 판의 네 변은 단순지지 되어 있다고 가정하였다. 역대칭 적층면재의 화이버 각도와 면재의 적층수를 변화시켜가며 휨해석의 결과를 나타내었다. 해석방법의 정확성을 위해 일반 적층판이론의 값과 비교를 하여 검증을 하였다. 그 결과 적층판이론으로 구한 값보다 처짐에 있어서 더 큰 값을 나타냄을 알 수 있었는데, 그 이유로는 본 해석방법이 면재, 심재 모두 휨강성과 전단변형을 고려하였기 때문이라 사료된다. 강재, 폴리머 복합면재를 갖는 샌드위치평판을 설계할 때 제시된 정보를 유용하게 이용될 수 있을 것이다.

• Journal of Mechanical Science and Technology
• /
• 제16권9호
• /
• pp.1033-1039
• /
• 2002

Partial penetration welding joint refers to the groove weld that applies to the one side welding which does not use steel backing and to both side welding without back gouging, that is, the partial penetration welding joint leaves an unwelded portion at the root of the welding area. In this study, we analyzed the residual stress and fracture on the thick metal plates that introduced the partial penetration welding method. According to the above-mentioned welding method, we could draw a conclusion that longitudinal stress and traverse stress occurred around the welding area are so minimal and do not affect any influence. We also performed the fracture behavior evaluation on the partial penetration multi pass welding with 25.4 mm thick plate by using the J-integral, which finally led us the conclusion that the partial penetration multi-pass welding method is more applicable and effective in handling the root face with less than 6.35 mm.

• 한국강구조학회 논문집
• /
• 제10권1호통권34호
• /
• pp.11-24
• /
• 1998

복합샌드위치평판은 복합재료를 갖으면서 강성이 있는 얇은 면재와 저밀도인 두꺼운 심재로 구성되어 있다. 본 연구에서는 국부전단변형을 고려한 복합면재를 갖는 샌드위치평판을 해석을 위한 지배방정식을 유도하였고, 해석적인 방법으로 해석을 하였다. 해석방법의 타당성을 확인하기 위하여 전체 전단변형을 고려한 일반 적층판 이론의 값과 비교하였다. 그리고 복합면재와 심재의 국부전단변형을 고려하였으므로 일반 적층판 해석에도 적용시킬 수 있음을 보였다.

• Steel and Composite Structures
• /
• 제3권3호
• /
• pp.213-229
• /
• 2003

A high precision shear deformable triangular element has been proposed for free vibration analysis of composite trapezoidal plates. The element has twelve nodes at the three sides and four nodes inside the element. Initially the element has fifty-five degrees of freedom, which has been reduced to forty-eight by eliminating the degrees of freedom of the internal nodes through static condensation. Plates having different side ratios (b/a), boundary conditions, thickness ratios (h/a=0.01, 0.1 and 0.2), number of layers and fibre angle orientations have been analyzed by the proposed shear locking free element. Trapezoidal laminate with concentrated mass at the centre has also been analyzed. An efficient mass lumping scheme has been recommended, where the effect of rotary inertia has been included. For validation of the present element and formulation few results of isotropic trapezoidal plate and square composite laminate have been compared with those obtained from open literatures. The numerical results for composite trapezoidal laminate have been given as new results.

• Steel and Composite Structures
• /
• 제47권3호
• /
• pp.365-374
• /
• 2023

This paper presents a new scheme for constructing locking-free finite elements in thick and thin plates, called Discrete Shear Gap element (DSG), using multiphase material topology optimization for triangular elements of Reissner-Mindlin plates. Besides, common methods are also presented in this article, such as quadrilateral element (Q4) and reduced integration method. Moreover, when the plate gets too thin, the transverse shear-locking problem arises. To avoid that phenomenon, the stabilized discrete shear gap technique is utilized in the DSG3 system stiffness matrix formulation. The accuracy and efficiency of DSG are demonstrated by the numerical examples, and many superior properties are presented, such as being a strong competitor to the common kind of Q4 elements in the static topology optimization and its computed results are confirmed against those derived from the three-node triangular element, and other existing solutions.