• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.15-21
• /
• 2000

Optical fiber temperature sensor, using resonance wavelength shifting of single mode fiber-to-planar waveguide coupler by heat, was fabricated. Thermo-optic polymers, have large change of refractive index due to heat, were used for planar waveguide. The device fabrication procedure including fiber polishing steps was illustrated and the device structure with independent polarization was demonstrated experimentally. The resonance wavelength difference of fabricated device was less than 2nm. The resonance wavelength shifting owing to temperature variation, from room temperature($24^{\circ}C$) to $90^{\circ}C$, was showed $-0.54nm/^{\circ}C$, $-3nm/^{\circ}C$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.5
• /
• pp.39-48
• /
• 2000

We newly proposed a polymer based vertical asymmetric optical coupler, which was characterized by simple fabricating procedure and short coupling length. And we fabricated a thermo-optic modulator using the polymeric optical coupler. We optimized the proposed device by coupling characteristic analysis. In a TE polarized 1.33${\mu}{\textrm}{m}$ wavelength, we obtained very short coupling length(L=277.6${\mu}{\textrm}{m}$) with 0.4${\mu}{\textrm}{m}$ thickness of middle layer, high coupling efficiency(94%), and asymmetric vertical waveguides with n$_{u}$ = 1.522, n$_{l}$ = 1.51. We implemented vortical asymmetric thermo-optic modulator with lower inverted rib waveguide and upper slab waveguide. In the 600Hz bandwidth and 4.5㎽ input power, the extinction ratio of the mode was 17㏈ with an insertion loss of 4.5㏈.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.253-256
• /
• 2000

We report the experimental results for the coupling properties of the an side-polished single-mode fiber covered with metal-clad planar waveguide. The experimental results show that the large birefringence of a metal-clad planar waveguide facilitates the effective separation of TE and TM polarization in the spectral domain. Additionally the resonant wavelengths of the device are tuned based in the thermo-optic effect of polymer planar waveguide.

• Korean Journal of Optics and Photonics
• /
• v.14 no.2
• /
• pp.135-141
• /
• 2003

In arrayed waveguide grating (AWG) devices whose waveguides were composed of polymer with negative thermo-optic coefficient as overcladding, and silica with positive thermo-optic coefficient as both core and undercladding, we investigated the temperature dependence of the central wavelength using two-dimensional SFDM. From these results, it was confirmed that the temperature dependence can be nearly eliminated by adjusting the refractive index of the cladding and the thickness of the silica thin film upper-loaded on the core. Based on the numerical calculations, the AWG device with polymer overcladding was fabricated. and its optical characteristics were compared with those of the orginal silica AWG device. The introduction of polymer overcladding decreased the temperature dependence of the central wavelength from 0.0130 nm/$^{\circ}C$ to 0.0028 nm/$^{\circ}C$ without deteriorating the insertion loss and crosstalk characteristics.

• Proceedings of the Optical Society of Korea Conference
• /
• 2005.02a
• /
• pp.292-295
• /
• 2005

Variable optical attenuators (VOA) made of low-loss fluorinated polymers are demonstrated which shows a low operating power less than 30 mW due to the superior thermo-optic effect of polymer material and a low insertion loss less than 1.0 dB by incorporating highly fluorinated polymers to reduce the absorption loss at 1550 nm. An attenuator-integrated low-crosstalk polymeric digital optical switch (DOS) is also demonstrated. The switch and attenuator shares a single connected electrode which is controlled by a single current source. Due to the simple structure of the integrated attenuator, the device length is reduced to 1 cm so as to provide low insertion loss of 0.8 and 1.1 dB for 1300 and 1550 nm, respectively. The attenuator radiates remained optical signal on the switch-off branch in order to decrease the switching crosstalk to be less than -70 dB with an applied electrical power of 200 mW.

• ETRI Journal
• /
• v.28 no.5
• /
• pp.615-620
• /
• 2006

In this paper, we discuss the quantification of Mach-Zehnder interferometer (MZI) thermal stabilization which is needed in optical phase shaped binary transmission (PSBT) links. Considering the thermo-optic and thermal expansion effects, we revisit the analytical expression for the thermal drift (GHz/$^{\circ}C$) of the MZI center frequency (denoted here by the 'MZI spectral drift'). An MZI is then used in an experimental transmission system using the optical PSBT format. We study the effect of spectral MZI drift by using a thermally stabilized interferometer and applying a frequency shift to the optical carrier. By using the thermal drift coefficient of the MZI, we find that to ensure low bit error rate fluctuations due to the MZI drift, the thermal stabilization of the device must have an accuracy of $0.5^{\circ}C$.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.475-479
• /
• 2006

An integrated photonic K-band microwave bandpass filter has been proposed and demonstrated by incorporating a polymeric ring resonator. Its transfer characteristics were adjusted by shilling the resonance wavelength of the ring resonator via the thermooptic effect. The achieved performance of the filter includes the center frequency of 20 GHz, the attenuation of ${\sim}15dB$, the bandwidth of 2 GHz, and the corresponding quality factor of 10. The microwave output power within the passband of the device was adjusted at the rate of about 6.7 dB/mW in the range of 27 dB. This kind of device with electrically controllable transfer characteristics can be applied to implement microwave switches and other devices.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.1
• /
• pp.39-46
• /
• 2002

High-senstivity temperature sensor based on the wavelength selectivity of single mode fiber-to-planar waveguide coupler, was demonstrated. The resonant wavelength of the coupler was shifted with large rate of -3.43nm/$^{\circ}C$ owing to good thermo-optic effects of polymer planar waveguide. The device design technique to reduce the polarization dependent properties and increase the temperature sensitivity was presented.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.10
• /
• pp.51-56
• /
• 2004

We propose and fabricate an 1${\times}$2 asymmetric optical switch by TOE using SOI wafer based on silicon which has very large TOE figure and it is a good material for optical devices. SOI wafer consists of 3 layers; upper Si layer for device(waveguide;core, n=3.5), buried oxide layer for insulator(clad, n=1.5) and Si substrate layer. We designed 1${\times}$2 asymmetric y-branched single mode optical waveguide switch by BPM simulation and metal heater by heat transfer simulation. Fabricated switch shows about 3.5 watts of power consumption and over 20dB of crosstalk between output channels.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.254-260
• /
• 2005

By incorporating large core polymer waveguides, which have been developed for increased alignment tolerance in passive fiber attachment, highly efficient variable optical attenuators are proposed. In order to find optimum device structures, 3-dimensional beam propagation method (BPM) simulations are performed. Heat distribution over the polymer film is calculated to find the 3-dimensional index profile data for the BPM simulation. Due to the small index contrast between the core and cladding materials in the large core waveguide, heat-induced radiation occurs for small heating power. While the ordinary VOA needs the temperature to change over $150^{\circ}C$ for 20 dB attenuation, the large core VOA requires only $70^{\circ}C$. In addition to the merit of passive fiber attachment, the proposed VOA has enhanced attenuation efficiency for the lower temperature change.