• 전기의세계
• /
• v.41 no.3
• /
• pp.38-42
• /
• 1992

써미스터(THERMLISTOR)는 Thermally Sensitive Resistor의 약칭으로 온도변화에 대한 저항치의 변화가 극히 크게 변화하는 특징을 갖는 감온반도체이다. 이중에는 부특성 또는 NTC(Negative Temperature Coeffient) THERMISTOR와 정특성 또는 PTC(Positive Temperature Coeffient)THERMISTOR의 두종류와 NTC와 동일한 부의 온도계수이지만 어떤 온도영역에서 저항치가 급격히 감소하는 CTR로 분류한다. 이렇게 3가지 종류로 분류되는 THERMISTOR중 우리주변에서 가장 널리 보급되고 가정생활에서 실제로 흔히 볼수 있는 가전기기의 온도검출용 sensor로 많이 사용되고 있는 THERMISTOR SENSOR에 대해서만 기초지식을 알아보기로 하고 다음기회에는 응용기술에 대해서 알아보기로 하겠다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.2
• /
• pp.88-92
• /
• 2003

The correlationship between heat treatment condition and electrical properties of the Mn-Co-Ni oxide NTC thermistor for fuel level sensor was investigated by the X-ray diffractometry, density measurement, and electrical properties measurement such as resistivity, B constant, and thermal dissipation constant. It was shown that the heat treatment of NTC thermistor was responsible for sinterability of Mn-Co-Ni oxide. The highest density of 5.10 g/㎤ was obtained at $1250^{\circ}C$, 2 hours, at which the densification was almost completed. This is also manifested from the microstructural observation. It is found that the electrical resistivity and B constant are increased at the elevated sintering temperatures. The NTC specimens prepared in this study showed the conventional decrease of resistance with the measured temperature and the linear behavior of output voltage with fuel levels. Therefore, the electrical properties of thermistor were closely correlated with sintering condition. and the Mn-Co-Ni oxide thermistor prepared in this study has a great possibility enough to apply for an automobile fuel level sensor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.347-350
• /
• 1995

In this paper, we fabricated fuel shortage detecting sensor, utilizing NTC thermistor concerned with Mn-Ni-Co system. We would be obtained B constant value of 1930∼2080 and resistivity 387∼430(ohm-cm) additive Bi$_2$O$_3$0∼0.5 wt% to Mn$_3$O$_4$:9wt%, Co$_3$O$_4$:61wt%, NiO:28wt% under 1150∼1250$^{\circ}C$ of sintering temperature. In sensor, we obtained characteristics, which we want, in resistance range 850∼l150$\Omega$, B constant 2000${\pm}$5%. we can see 15 multiplied differences between gasoline and heat dissipation coefficient of air condition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.2
• /
• pp.103-110
• /
• 2016

Fine wires made from platinum have been used as sensors to evaluate the convection performance of nanofluids. However, the wire sensor is difficult to handle due to its fragility. Additionally, an unrealistic convective heat transfer coefficient (h) is obtained if a rigorous calibration process combined with precision equipment is not used for measurement. This paper proposes a new evaluation apparatus for h of nanofluids that uses a thermistor sensor instead of the platinum wire. The working principles are also explained in detail. Validation experiments for pure engine oil comparing h from the two sensors confirmed numerous practical benefits of the thermistor. The proposed system can be used as a useful tool to justify the adoption of developed nanofluids.

• Journal of Sensor Science and Technology
• /
• v.3 no.3
• /
• pp.3-8
• /
• 1994

Flow sensor was fabricated with PTC thermistor usually operating as thermostats. The PTC thermistor was manufactured with $(Ba_{0.7}Sr_{0.3})TiO_{3}$ powder and its resistivity as a function of flow velocity was investigated. The resistivity changed from 4.45 $k{\Omega}{\cdot}cm$ to 3.95 $k{\Omega}{\cdot}cm$ as flow velocity varied 0 cm/s to 5 cm/s The sensitivities of the PTC thermistor were -204 (${\Omega}{\cdot}cm$)/(cm/s) and -24 (${\Omega}{\cdot}cm$)/(cm/s) at the flow velocity of 1 cm/s and 5 cm/s, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.228-229
• /
• 2009

$VO_2$ thermistor was fabricated on $Al_2O_3$ substrate. and has a CTR (Critical Temperature Resistor) characteristic. $VO_2$ thermistor has a about $10^6$ resistance($\Omega$) in normal temperature. But When temperature is a about $80^{\circ}C$, Resistance of $VO_2$ thermistor is a about some hundred resistance: The resistance of $VO_2$ thermistor increased with increasing length and decreasing width.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.6
• /
• pp.297-303
• /
• 2003

Mn-Ni-Co type thin films were prepared at various conditions by a rf magnetron sputtering system. At the condition. or substrate temperature of $300^{\circ}C$ and $Ar/O_2$= 10/0, a cubic spinel phase was obtained. When oxygen was included in process gas, a cubic spinel phase was not formed even after the thermal annealing at $900^{\circ}C$. The thermistor thin film had no other elements except Mn, Ni and Co. The infrared reflection spectra of the thermistor thin films showed that the films had somewhat high reflectance for incoming infrared ray with some angle. The etch rate of the thermistor thin films was about 63nm/min at a condition of DI water : $HNO_3$: HCl = 60 : 30 : 10 vol%. The B constant and temperature coefficient of resistance of the thermistor thin films were 3500 K and -3.95 %/K, respectively. The voltage responsivity of the thermistor thin film infrared sensor was 108.5 V/W and its noise equivalent power and specific detectivity were $5.1\times 10^{-7}$ W/$Hz^{-1/2}$ and $0.2\times 10^6$cm $Hz^{1/2}$/W, respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.11a
• /
• pp.165-165
• /
• 1999

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.6
• /
• pp.1165-1169
• /
• 2007

In this study, a novel sensor system for measuring the temperature inside an oral cavity is proposed. With this aim, a small size of thermistor was used for resolving the cavity's temperature with the resolution of $0.1^{\circ}C$. To evaluate effectiveness of our sensor system, the temperature and its output voltage characteristic, and the specifications of response are investigated. It turned out to be that our sensor system has a linear property in terms of temperature variations for a healthy subject's body temperature range and has a good response time within 3 seconds. Also, in order to investigate the medical application, our sensor system is sought to measure the real temperature variations of a subject's oral cavity and ark shell especially for 'before' and 'after' exercise mode.

• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.198-205
• /
• 1991

Sintered thermistor body was fabricated by solid reaction method using $Fe_2O_3, \;Al_2O_3, \;TiO_2$ and Si powder. Surface matrix of sintered body was investigated by SEM and $\beta$-constant was obtained from measurement of resistance variation in liquid bath. The values of thermistor constant $\beta$ of samples in the temperature range $-50~+50^{\circ}C$ were distributed from 927 to 4005k. This thermistor body can be used as temperature sensor for radiosonde.