• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 한국해양환경ㆍ에너지학회지
• /
• 제19권3호
• /
• pp.227-235
• /
• 2016

최근 해양에서 이루어지고 있는 해역이용 개발 현황 분석을 통해 입지의 적정성과 환경영향 측면에서 상충될 수 있는 대표적인 개발사례를 진단하여 해양공간계획수립의 필요성에 대한 시사점을 제공하였다. 해양 신재생에너지개발(조력 및 해상풍력), 바다골재채취, 공유수면매립, 연안골프장 조성, 온배수 및 고염수 배출, 침식영향 개발사업 등의 주요 사례 분석결과, 해당 공간이용 및 관리방향 간의 상충성이 빈발하고, 누적환경영향에 따른 해양환경과 생태계 훼손, 어장이용과 이행당사자사이의 갈등이 지속적으로 나타나고 있는 상황이다. 이러한 이유는 개발 입지 및 주변 공간영역에 대한 충분한 현황 파악이 부족하고, 공간이용과 관련된 개별법의 상호성 및 연계성 평가가 미흡한 것과 관련되어 있다. 사전예방적인 해양환경관리 정책을 강화하기 위해서는 입지 적정성과 개발규모에 대한 평가 검토를 강화해야 할 것이다. 특히, 전략환경영향평가 등 상위계획 심의단계에서 입지와 규모의 적정성에 대한 평가 시, 해양공간이용 현황, 상위계획과 지역계획간의 연계성(특히, 연안관리지역계획과 통합계획), 해양수산규제지역과 보호대상 해양생물 분포 등 핵심 평가사항을 제시하도록 하여 보다 철저한 진단이 이루어져야 할 것이다. 지속가능한 보전과 개발의 조화를 위해서는 TOP-DOWN 방식의 해양공간계획 전략(연안과 EEZ, 광역과 협역 해역 등 전체적 Zoning과 Sector 연계성을 강화, 3차원 정보 포함 등)을 마련해야 하고, 이 과정에서 체계적이고 최신의 해양공간정보 속성자료 파악 및 공유를 위한 통합 정보시스템 구축이 필요할 것으로 판단된다. 해양수산과 관련된 전 부문, 즉, 항만 어항, 수산, 연안관리, 해양환경과 생태계 분야에서 해양공간이용의 상호적이고 일관성있는 전략이 필요할 것이다.

• 한국재료학회지
• /
• 제8권7호
• /
• pp.621-627
• /
• 1998

단결정 Si(100) 기판과 비정질 Si 기판위에 Co/Zr 이중층을 이용하여 형성시킨 Co 실리사이드의 성장 거동에 대하여 연구하였다. 전자빔 증착기를 사용하여 단결정과 비정질 Si 기판위에 Zr $50\AA$과 Co $100\AA$을 차례로 증착한 박막을 50$0^{\circ}C$부터 $800^{\circ}C$까지 $100^{\circ}C$ 간격으로 질소 분위기에서 30초 동안 급속열처리를 하여 Co 실리사이드를 형성시켰다. 각 온도에서 열처리된 시편의 상형성, 화학적 조성, 계면의 형상, 전기적 특성을 XRD, AES, RBS, TEM, HRTEM 등으로 분석하였다. 분석 결과 $CoSi_2$ 상이 단결정 기판에서는 $700^{\circ}C$ 이상에서 기판과 정합성장을 하였고 비정질 기판에서는 다결정 성장을 하였으며 Co 실리사이드의 상형성 온도는 단결정 기판에서보다 비정질 기판에서 $100^{\circ}C$정도 낮아졌다. $CoSi_2$와 같은 Co rich 중간상은 두 기판 모두 형성되지 않았으며 초기 Co 실리사이드의 상형성 온도는 Co 단일층으로 상을 형성시킬 때 보다 더 높았다. Co 실리사이드와 Si 기판의 계면의 형상은 단결정 기판의 경우보다 비정질 기판에서 더 균질하였다. 박막의 면저항은 $600^{\circ}C$이하의 열처리 온도에서는 비정질 기판에서 형성된 Co 실리사이드 박막이 더 낮은 값을 나타내었고 그 이상의 열처리 온도에서는 단결정 기판에서 형성된 박막의 면저항값이 더 낮은 값을 나타내었으며 두가지 기판에서 형성된 박막 모두$ 800^{\circ}C$에서 가장 낮은 면저항 값을 보였다.TEX>$10^{-8}$ A/$\textrm{cm}^2$로 양질의 SrTiO$_3$박막을 제조하였다.는 과정에서 전세계 수준에서 멸종위기 식물을 목록화가 필요하다. 특히, 목록 작업이 완성되면 해당 분류군에 대한 기본적인 자료 수집과 장단기 조사과정으로서, 해당 분류군에 대한 멸종위협 요인을 수집하고, 이 자료를 근간으로 정량적으로 IUCN 적색목록 평가방식이 추진할 필요가 있다.he oscillations are active in the derived unit hydrograph. 3)The parameter estimates are validated by extending the model to the Soyang river Dam site with elimination of the autocorrelation in the disturbances. Finally, this paper illustrates the application of the multiple regression model to drive an optimal unit hydrograph dealing with the multicollinearity and the autocorrelation which cause some problems. 우선적으로 고려하여 사용할 농약을 선택해야 할 것으로 보이나, 그 외 약제의 잔류성, 사용량, 사용시기와 함께 기후조건, 토양의 투수성, 토층이 깊이, 지하수 깊이 등의 지역적인 특성들이 농약의 용탈잠재성에 미치는 영향도 더욱 구체적으로 파악되어야 할 것이며 농약의 선택 과정에서도 이러한 특성들이 앞으로 고려되어야 할 것이다.calenol 및 citrostadienol 등이 함유(含有)되어 있었다. 6. 4-desmethylsterol fraction에 는 sitosterol (74.6%)이

• 한국식품영양과학회지
• /
• 제11권1호
• /
• pp.51-56
• /
• 1982

가공식품(加工食品)의 가장 중요(重要)한 색소형성(色素形成)으로 알려 진 비효소적(非酵素的) 갈변반응(褐變反應)인 amino-carbonyl반응(反應)에 대(對)한 온도(溫度)의 영향을 규명(究明)하기 위하여 0.05M glucose-arginine을 model system으로 선정하여 처리온도(處理溫度) 및 시간(時間)에 따라 분해(分解)되는 glucose 및 arginine의 함량변화(含量變化)와 생성(生成)되는 melanoidin 색소(色素)의 강도(强度)로써 반응속도상수(反應速度常數)와 반감기(半減期)를 구(求)하였으며, 또 Arrhenius 식(式)에 따라 반응속도상수(反應速度常數)의 온도의존성(溫度依存性)을 조사(調査)하였다. 1. 처리온도(處理溫度) 및 시간별(時間別)로 분해(分解)되는 glucose 및 arginine의 정량(定量)은 carbohydrate analysis 및 $\mu$ Bondapak $C_{18}$ column을 사용(使用)한 HPLC를 이용(利用)함이 효과적(效果的)이었다. 2. glucose 및 arginine의 분해반응(分解反應)은 $100^{\circ}C$ 및 $120^{\circ}C$에서의 glucose를 제외하고는 모두 1차반응(次反應)에 따랐으나, $100^{\circ}C$이상에서의 glucose에 있어서는 2상(相) 1차반응(次反應)(two-phase first-order reaction)에 따랐다. 또 melanoidin 생성반응(生成反應)에 있어서 $60^{\circ}C$ 및 $80^{\circ}C$에서는 1차반응(次反應)에 따랐으나 $100^{\circ}C$이상에서는 역시 2상(相) 1차반응(次反應)에 따랐다. 3. glucose-arginine 반응(反應)에 의한 melanoidin 색소(色素)의 생성반응(生成反應)은 $100^{\circ}C$ 및 $120^{\circ}C$에서 3$\sim$5시간(時間)동안에 거의 완성단계에 있었으며 $100^{\circ}C$이상에서는 거의 차(差)가 없었다. 4. glucose 및 arginine의 분해반응(分解反應)과 melanoidin의 생성반응(生成反應)의 속도상수(速度常數)가 $100^{\circ}C$ 및 $120^{\circ}C$에서 현저한 증가현상(增加現象)을 나타내므로 amino-carbonyl 반응(反應)에 의(依)한 갈색색소형성(褐色色素形成)은 $100^{\circ}C$이상의 고온에서 심하게 일어남을 알 수 있었다. 5. glucose 및 arginine의 분해반응(分解反應)과 이에 따른 melanoidin의 생성반응(生成反應)에 대(對)한 반응속도상수(反應速度常數)의 온도(溫度) 의존성(依存性)은 $100^{\circ}C$이하에서는 Arrhenius식(式)에 따랐으나 $120^{\circ}C$이상의 고온(高溫)에서는 이에 따르지 않았다. 6. glucose 및 arginine 분해반응(分解反應)의 활성화(活性化)에너지는 각각(各各) 12.512kcal/mole과 12.122kcal/mole로서 거의 비슷하고 melanoidin생성반응(生成反應)의 활성화(活性化)에너지는 18.142kcal/mole로서 melanoidin생성반응(生成反應)이 온도(溫度)에 더 민감함을 보여주었다.

• 한국해양환경ㆍ에너지학회지
• /
• 제8권2호
• /
• pp.100-110
• /
• 2005

2004년 이른 여름 한국남해 및 동중국해 북부해역의 해양환경과 식물플랑크톤 군집의 분포특성을 파악하기 위해 2004년 6월 동중국해 북부해역인 한국남해 해역을 대상으로 현장조사를 실시하였다. 결과 동중국해 북부해역은 3개의 서로 다른 수괴세력에 의해 해양환경이 지배되고 있었다. 여름 한국남해를 포함하는 동중국해 북부해역에 영향을 주는 수괴는 저온, 저염으로 제주서쪽해역의 표층에 강한 세력을 확장하는 중국대륙연안수와 저은, 저염 및 고밀도로 제주서측 저층에 탁월한 황해저층냉수 그리고 고온, 고염 특성으로 제주 동쪽과 한국남동해역에 넓게 분포하는 쓰시마난류수로 구분되었다. 각 수괴 사이에는 불연속면에 의한 수온약층과 전선이 형성되었으며, 수온 및 밀도, 약층은 정점에 따라 5 m에서 30 m 수심에, 용승에 의한 전선은 여수, 고흥반도 인근인 남해중앙부 해역에서 관찰되었다. 식물플랑크톤 군집은 26속 44종으로 매우 단조로운 종조성을 나타내었으며, 와편모조류인 Prorocentrum triestinum과 Scrippsiella trochoidea에 의해 우점하였다. 식물플랑크톤 현존량은 100 cells/L에서 10,800 cells/L 범위로 변화하였으나, 표층이 성층해역보다 높은 현존량을 나타내었다. 규조류는 쓰시마난류역에 주로 출현하는 반면, 편모 조류는 저염을 나타내는 해수와 전선역에서 출현하는 특성을 보였고, 전체 현존량 및 생물량은 편의조류에 의해 지배되었다. 식물플랑크톤 생물량(Chl-a)은 $0.09{\mu}g/L$에서 $2.59{\mu}g/L$로 변화하였으나, 현존량과는 달리 수온약층이나 아표층에서 표층보다 높은 생물량을 나타내었으며, 중국대륙연안수의 확장에 의해 생산이 지배되는 특성을 나타내었다.

• 대한치과보철학회지
• /
• 제40권1호
• /
• pp.1-17
• /
• 2002

The purpose of this study is to examine the possibility of thermal injury to bone tissues during an implant site preparation under the same condition as a typical clinical practice of $Br{\aa}nemark$ implant system. All the burs for $Br{\aa}nemark$ implant system were studied except the round bur The experiments involved 880 drilling cases : 50 cases for each of the 5 steps of NP, 5 steps of RP, and 7 steps of WP, all including srew tap, and 30 cases of 2mm twist drill. For precision drilling, a precision handpiece restraining system was developed (Eungyong Machinery Co., Korea). The system kept the drill parallel to the drilling path and allowed horizontal adjustment of the drill with as little as $1{\mu}m$ increment. The thermocouple insertion hole. that is 0.9mm in diameter and 8mm in depth, was prepared 0.2mm away from the tapping bur the last drilling step. The temperatures due to countersink, pilot drill, and other drills were measured at the surface of the bone, at the depths of 4mm and 8mm respectively. Countersink drilling temperature was measured by attaching the tip of a thermocouple at the rim of the countersink. To assure temperature measurement at the desired depths, 'bent-thermocouples' with their tips of 4 and 8mm bent at $120^{\circ}$ were used. The profiles of temperature variation were recorded continuously at one second interval using a thermometer with memory function (Fluke Co. U.S.A.) and 0.7mm thermocouples (Omega Co., U.S.A.). To simulate typical clinical conditions, 35mm square samples of bovine scapular bone were utilized. The samples were approximately 20mm thick with the cortical thickness on the drilling side ranging from 1 to 2mm. A sample was placed in a container of saline solution so that its lower half is submerged into the solution and the upper half exposed to the room air, which averaged $24.9^{\circ}C$. The temperature of the saline solution was maintained at $36.5^{\circ}C$ using an electric heater (J. O Tech Co., Korea). This experimental condition was similar to that of a patient s opened mouth. The study revealed that a 2mm twist drill required greatest attention. As a guide drill, a twist drill is required to bore through a 'virgin bone,' rather than merely enlarging an already drilled hole as is the case with other drills. This typically generates greater amount of heat. Furthermore, one tends to apply a greater pressure to overcome drilling difficulty, thus producing even greater amount heat. 150 experiments were conducted for 2mm twist drill. For 140 cases, drill pressure of 750g was sufficient, and 10 cases required additional 500 or 100g of drilling pressure. In case of the former. 3 of the 140 cases produced the temperature greater than $47^{\circ}C$, the threshold temperature of degeneration of bone tissue (1983. Eriksson et al.) which is also the reference temperature in this study. In each of the 10 cases requiring extra pressure, the temperature exceeded the reference temperature. More significantly, a surge of heat was observed in each of these cases This observations led to addtional 20 drilling experiments on dense bones. For 10 of these cases, the pressure of 1,250g was applied. For the other 10, 1.750g were applied. In each of these cases, it was also observed that the temperature rose abruptly far above the thresh old temperature of $47^{\circ}C$, sometimes even to 70 or $80^{\circ}C$. It was also observed that the increased drilling pressure influenced the shortening of drilling time more than the rise of drilling temperature. This suggests the desirability of clinically reconsidering application of extra pressures to prevent possible injury to bone tissues. An analysis of these two extra pressure groups of 1,250g and 1,750g revealed that the t-statistics for reduced amount of drilling time due to extra pressure and increased peak temperature due to the same were 10.80 and 2.08 respectively suggesting that drilling time was more influenced than temperature. All the subsequent drillings after the drilling with a 2mm twist drill did not produce excessive heat, i.e. the heat generation is at the same or below the body temperature level. Some of screw tap, pilot, and countersink showed negative correlation coefficients between the generated heat and the drilling time. indicating the more the drilling time, the lower the temperature. The study also revealed that the drilling time was increased as a function of frequency of the use of the drill. Under the drilling pressure of 750g, it was revealed that the drilling time for an old twist drill that has already drilled 40 times was 4.5 times longer than a new drill The measurement was taken for the first 10 drillings of a new drill and 10 drillings of an old drill that has already been used for 40 drillings. 'Test Statistics' of small samples t-test was 3.49, confirming that the used twist drills require longer drilling time than new ones. On the other hand, it was revealed that there was no significant difference in drilling temperature between the new drill and the old twist drill. Finally, the following conclusions were reached from this study : 1 Used drilling bur causes almost no change in drilling temperature but increase in drilling time through 50 drillings under the manufacturer-recommended cooling conditions and the drilling pressure of 750g. 2. The heat that is generated through drilling mattered only in the case of 2mm twist drills, the first drill to be used in bone drilling process for all the other drills there is no significant problem. 3. If the drilling pressure is increased when a 2mm twist drill reaches a dense bone, the temperature rises abruptly even under the manufacturer-recommended cooling conditions. 4. Drilling heat was the highest at the final moment of the drilling process.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.154-155
• /
• 2012

The promise of nano-crystalites (nc) as a technological material, for applications including display backplane, and solar cells, may ultimately depend on tailoring their behavior through doping and crystallinity. Impurities can strongly modify electronic and optical properties of bulk and nc semiconductors. Highly doped dopant also effect structural properties (both grain size, crystal fraction) of nc-Si thin film. As discussed in several literatures, P atoms or radicals have the tendency to reside on the surface of nc. The P-radical segregation on the nano-grain surfaces that called self-purification may reduce the possibility of new nucleation because of the five-coordination of P. In addition, the P doping levels of ${\sim}2{\times}10^{21}\;at/cm^3$ is the solubility limitation of P in Si; the solubility of nc thin film should be smaller. Therefore, the non-activated P tends to segregate on the grain boundaries and the surface of nc. These mechanisms could prevent new nucleation on the existing grain surface. Therefore, most researches shown that highly doped nc-thin film by using conventional PECVD deposition system tended to have low crystallinity, where the formation energy of nucleation should be higher than the nc surface in the intrinsic materials. If the deposition technology that can make highly doped and simultaneously highly crystallized nc at low temperature, it can lead processes of next generation flexible devices. Recently, we are developing a novel CVD technology with a neutral particle beam (NPB) source, named as neutral beam assisted CVD (NBaCVD), which controls the energy of incident neutral particles in the range of 1~300eV in order to enhance the atomic activation and crystalline of thin films at low temperatures. During the formation of the nc-/pm-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. In the case of phosphorous doped Si thin films, the doping efficiency also increased as increasing the reflector bias (i.e. increasing NPB energy). At 330V of reflector bias, activation energy of the doped nc-Si thin film reduced as low as 0.001 eV. This means dopants are fully occupied as substitutional site, even though the Si thin film has nano-sized grain structure. And activated dopant concentration is recorded as high as up to 1020 #/$cm^3$ at very low process temperature (＜ $80^{\circ}C$) process without any post annealing. Theoretical solubility for the higher dopant concentration in Si thin film for order of 1020 #/$cm^3$ can be done only high temperature process or post annealing over $650^{\circ}C$. In general, as decreasing the grain size, the dopant binding energy increases as ratio of 1 of diameter of grain and the dopant hardly be activated. The highly doped nc-Si thin film by low-temperature NBaCVD process had smaller average grain size under 10 nm (measured by GIWAXS, GISAXS and TEM analysis), but achieved very higher activation of phosphorous dopant; NB energy sufficiently transports its energy to doping and crystallization even though without supplying additional thermal energy. TEM image shows that incubation layer does not formed between nc-Si film and SiO2 under later and highly crystallized nc-Si film is constructed with uniformly distributed nano-grains in polymorphous tissues. The nucleation should be start at the first layer on the SiO2 later, but it hardly growth to be cone-shaped micro-size grains. The nc-grain evenly embedded pm-Si thin film can be formatted by competition of the nucleation and the crystal growing, which depend on the NPB energies. In the evaluation of the light soaking degradation of photoconductivity, while conventional intrinsic and n-type doped a-Si thin films appeared typical degradation of photoconductivity, all of the nc-Si thin films processed by the NBaCVD show only a few % of degradation of it. From FTIR and RAMAN spectra, the energetic hydrogen NB atoms passivate nano-grain boundaries during the NBaCVD process because of the high diffusivity and chemical potential of hydrogen atoms.

• 대한원격탐사학회지
• /
• 제28권1호
• /
• pp.69-77
• /
• 2012

표면도달일사량은 전 지구시스템에 대한 기후 연구에 가장 중요한 요소 중 하나다. 기후 연구에서는 동일 지역을 관측하는 두 개 혹은 그 이상의 위성자료로부터 넓은 공간적 범위를 가지는 장기간의 데이터를 사용하는 것이 필요하다. 시간적 연속성을 가지는 서로 다른 위성으로부터 산출 된 표면도달일사량의 연속성과 일관성을 향상시키는 것은 매우 중요하다. 본 연구에서는 물리적 모델을 이용하여 GOES-9과 MTSAT-1R 위성의 중복 관측 기간 동안의 표면도달일사량을 산출하고, 두 위성의 채널자료와 실측치 비교를 통해 위성간의 연속성과 일관성을 향상시키는 방법을 연구하였다. 두 위성의 적외 채널 온도는 매우 잘 일치하는 경향을 보였다 : RMSE=5.595 Kelvin; Bias=2.065 Kelvin. 반면에, 가시채널은 다른 값의 분포를 보였지만 비슷한 경향을 보였다. 그리고 두 위성으로부터 산출 된 표면도달일사량은 실측치와 일치성이 낮았다. 표면도달일사량의 품질 향상을 위해 구름감쇠계수 조정을 통해 표면도달일사량 산출물을 재생산하였다. 그리고 채널 자료의 비교 분석을 통해 GOES-9 위성을 위한 구름감쇠계수를 생산하였다. 그 결과, 구름 효과를 고려한 GOES-9의 표면도달일사량 산출물은 MTSAT-1R과 실측치에 대해 매우 높은 일치성을 보였다 : RMSE=$83.439W\;m^{-2}$; Bias=$27.296W\;m^{-2}$. 구름감쇠계수 조정을 통해 향상 된 정확도는 두 개 이상의 위성으로부터 산출 된 표면도달일사량 산출물의 연속성과 일관성을 향상 시킬 수 있을 것이다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2003년도 제20회 춘계학술대회 논문집
• /
• pp.91-93
• /
• 2003

A comprehensive numerical study is carried out to investigate for the understanding of the flow evolution and flame development in a supersonic combustor with normal injection of ncumally injecting hydrogen in airsupersonic flows. The formulation treats the complete conservation equations of mass, momentum, energy, and species concentration for a multi-component chemically reacting system. For the numerical simulation of supersonic combustion, multi-species Navier-Stokes equations and detailed chemistry of H2-Air is considered. It also accommodates a finite-rate chemical kinetics mechanism of hydrogen-air combustion GRI-Mech. 2.11[1], which consists of nine species and twenty-five reaction steps. Turbulence closure is achieved by means of a k-two-equation model (2). The governing equations are spatially discretized using a finite-volume approach, and temporally integrated by means of a second-order accurate implicit scheme (3-5).The supersonic combustor consists of a flat channel of 10 cm height and a fuel-injection slit of 0.1 cm width located at 10 cm downstream of the inlet. A cavity of 5 cm height and 20 cm width is installed at 15 cm downstream of the injection slit. A total of 936160 grids are used for the main-combustor flow passage, and 159161 grids for the cavity. The grids are clustered in the flow direction near the fuel injector and cavity, as well as in the vertical direction near the bottom wall. The no-slip and adiabatic conditions are assumed throughout the entire wall boundary. As a specific example, the inflow Mach number is assumed to be 3, and the temperature and pressure are 600 K and 0.1 MPa, respectively. Gaseous hydrogen at a temperature of 151.5 K is injected normal to the wall from a choked injector.A series of calculations were carried out by varying the fuel injection pressure from 0.5 to 1.5MPa. This amounts to changing the fuel mass flow rate or the overall equivalence ratio for different operating regimes. Figure 1 shows the instantaneous temperature fields in the supersonic combustor at four different conditions. The dark blue region represents the hot burned gases. At the fuel injection pressure of 0.5 MPa, the flame is stably anchored, but the flow field exhibits a high-amplitude oscillation. At the fuel injection pressure of 1.0 MPa, the Mach reflection occurs ahead of the injector. The interaction between the incoming air and the injection flow becomes much more complex, and the fuel/air mixing is strongly enhanced. The Mach reflection oscillates and results in a strong fluctuation in the combustor wall pressure. At the fuel injection pressure of 1.5MPa, the flow inside the combustor becomes nearly choked and the Mach reflection is displaced forward. The leading shock wave moves slowly toward the inlet, and eventually causes the combustor-upstart due to the thermal choking. The cavity appears to play a secondary role in driving the flow unsteadiness, in spite of its influence on the fuel/air mixing and flame evolution. Further investigation is necessary on this issue. The present study features detailed resolution of the flow and flame dynamics in the combustor, which was not typically available in most of the previous works. In particular, the oscillatory flow characteristics are captured at a scale sufficient to identify the underlying physical mechanisms. Much of the flow unsteadiness is not related to the cavity, but rather to the intrinsic unsteadiness in the flowfield, as also shown experimentally by Ben-Yakar et al. [6], The interactions between the unsteady flow and flame evolution may cause a large excursion of flow oscillation. The work appears to be the first of its kind in the numerical study of combustion oscillations in a supersonic combustor, although a similar phenomenon was previously reported experimentally. A more comprehensive discussion will be given in the final paper presented at the colloquium.

• 한국석유지질학회지
• /
• 제8권1_2
• /
• pp.1-43
• /
• 2000

황해 및 인접 지역에 위치하는 퇴적 분지들의 구조적 진화에 따른 층서를 이해하기 위한 비교 연구가 통합층서기술을 이용하여 수행되었다. 본 연구의 잠정적 결과로 우리는 각 분지별 퇴적층들의 시$\cdot$공간상의 대비가 가능한 층서틀을 제안한다. 본 연구의 결과로 제안된 층서틀은 향후 황해 및 인접 지역의 석유자원 탐사를 위한 새로운 층서적 사고의 틀로 사용될 수 있을 것이다. 생층서 자료와 결합시켜 수행한 통합층서해석 결과, 캠브로-오오도비스기, 석탄기-트라이아스기, 쥬라기 초기-중기, 쥬라기 말기-백악기 초기, 백악기 후기, 팔레오세-에오세, 올리고세, 마이오세 초기, 마이오세 중기-플라이오세 퇴적층 등 9개의 단위층들이 인지된다. 본 연구를 통해 인지된 9개 단위층들은 구조층서단위로 황해 및 인접 지역 퇴적 분지들의 퇴적 작용 및 분지 형성과 변형에 관련된 구조운동 등에 관한 정보를 제공해 준다 남황해 분지는 고생대 동안 남중국 지괴의 북쪽 연변부에 발달하는 대륙 연변부 분지로 시작되었다 쇄설성 및 탄산염 퇴적물들이 상대적 해수면의 변동에 따라 윤회성을 보이면서 분지 내에 퇴적되었다. 그러나, 데본기 동안의 칼레도니안 조산운동에 의해 분지는 융기되어 침식을 받았으며, 결과로 캠브로-오오도비스기 단위층과 석탄기-트라이아스기 단위층 사이에 부정합이 형성되었다. 북중국 지괴와 남중국 지괴가 충돌될 때인 페름기 말기로부터 트라이아스기 말기 사이에 인도시니안 조산운동이 일어났다. 북중국 지괴와 남중국 지괴의 충돌에 따라 친링-다비-수루-임진강 습곡대가 형성되었으며, 고생대 퇴적층들은 융기된 후 변형을 받게 되었다. 이 후 습곡대에 평행한 대륙전사면이 빠르게 침강하면서 발해 분지 및 서한만 분지와 같은 대륙전사면 분지가 형성되어 쥬라기 초기-중기의 후조산성 퇴적물들이 분지를 충진시켰으며, 지역적으로 피기백 형태의 소규모 분지들이 저각의 역단층을 따라 발달하게 되었다. 이들 대륙전사면 분지나 피기백 형태의 분지들은 쥬라기 말기 동안에 일어나는 앤샤니안 조산운동 (일차)에 의해 변형된다. 그러나, 남황해 분지는 쥬라기 초기 및 중기 동안에 대륙내 침강 분지였던 것으로 보인다. 남황해 분지의 쥬라기 초기 및 중기 단위층은 분급도와 원마도가 양호한 규암역을 포함하는 두꺼운 기저 역암층과 함께 하성 및 호성 환경 하에서 퇴적된 사암 및 셰일들로 구성되어 있다. 한편, 탄루 단층대는 트라이아스기 말기로부터 좌수향의 운동을 시작하였으며, 쥬라기와 백악기를 거쳐 제삼기 초까지 계속되었다. 쥬라기 말기에 들어와 탄루 탄층대를 따라 이차 및 삼차 순위의 주향이동 단층들이 발달되면서 소규모 열개 분지들이 형성되기 시작하였다. 에오세말까지 지속된 탄루 단층의 이동에 의해 남황해 분지는 대규모의 횡압력을 받게되어 소규모 열개 분지들은 인리형 분지로 확장되었다. 그러나 쥬라기 말기와 에오세 말기까지 발해 분지는 융기되어 심한 변형을 받게되었다. 발해 분지의 백악기 초기 이후 에오세 말기까지의 부정합이 앤샤니안 조산운동 (이차 및 삼차)에 의해 형성된 것으로 해석된다. 한편 에오세 말에 이르러 인도판과 유라시아판의 충돌에 의한 히말라얀 조산운동의 영향으로 탄루 단층의 이동방향이 좌수향에서 우수향으로 변환되기 시작하면서 남황해 분지는 구조역전의 현상이 일어났으며, 동시에 발해 분지는 인리형 분지로 발달하게 되었다. 따라서, 올리고세 동안 발해 분지에서는 퇴적작용이, 남황해 분지에서는 심한 구조역전에 의한 분지변형이 동시에 일어났다 올리고세 이후 현재까지, 남황해 분지와 발해 분지들은 간헐적인 해침과 함께 광역적 침강을 유지하면서 안정된 대륙 및 대륙붕 지역으로 전이되었다.