• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.294-299
• /
• 2008

Steam reforming of methane is the most wide spread method for hydrogen production. It has heed studied more than 60 years. methane reforming has advantages in technological maturity and economical production cost. Using a high-temperature solar thermal energy is an advanced technology in Steam reforming process. The synthesis gas, the product of the reforming process, can be applied directly for a combined cycle or separated for a hydrogen. In this paper, hydrogen conversion rate of a solar chemical reactor is calculated using commercial CFD program. 2 models are considered. Model-1 is original model which is designed from the former researches. And model-2 is ring-disk set of baffle is inserted to enhance the performance. The solar chemical reactor has 3 inlet nozzle at the bottom of the side wall near quartz glass and an exit is located at the top. Methane and steam is premixed with 50:50 mole fraction and goes into the inside. Passing through the porous media, the reactants are conversed into hydrogen and carbon monoxide.

• 대한토목학회논문집
• /
• 제14권4호
• /
• pp.771-781
• /
• 1994

매스콘크리트에서 시멘트의 수화반응에 의해 발생되는 열은 약재령 콘크리트(young concrete)에서 내부온도의 증가와 체적변화를 초래하므로 외적인 구속이 존재하면 구조물에는 인장응력이 발생하고 이는 구조물에 균열을 일으킬 수 있다. 따라서 매스콘크리트의 설계와 시공단계에서 균열을 제어하기 위해서는 온도응력을 정확하게 예측하는 것이 매우 중요하다. 또한 약재령 콘크리트에서는 크리이프 효과가 노재령 콘크리트(old concrete)의 경우에 비하여 현저하게 크므로 이를 반드시 고려하여야 할 것이다. 이 논문은 매스콘크리트에서의 온도에 관한 시간이력을 구하고 크리이프와 각 요소의 온도를 고려한 탄성계수를 적용하여 온도응력을 구하는 유한요소 프로그램을 개발하는데 그 목적이 있다. 개발된 프로그램의 해석결과를 문헌의 자료들과 비교해 볼 때 온도균열의 제어에 가장 중요한 내부에서의 온도이력과 응력이 실험결과와 잘 부합되고 있다. 따라서, 이 논문의 해석방법은 매스콘크리트 구조물의 설계와 시공단계에서 균열의 제어를 위해 유용하게 사용될 수 있을 것이다.

• 한국식품영양학회지
• /
• 제16권3호
• /
• pp.180-186
• /
• 2003

가열살균 처리시의 온도값을 이용하여 다양한 미생물들의 가열살균 효과를 D값, z값 등의 미생물 내열성 특성치와 kinetic 모델 및 수식을 이용하여 살균치 계산을 컴퓨터를 이용하여 수행함으로써 target 미생물의 살균정도를 예측하고자, Excel과 Visual Basic을 연동하여 작성된 시스템으로 Excel을 기본으로 사용한 프로그램을 개발하였다. 가열살균 target 미생물을 선택하고자 야채식품을 기반으로 하는 식품에서의 미생물을 검토하여, 내열성인 가장 큰 호기성 포자형성균인 Bacillus spp. 계통이 산을 형성하여 맛 등의 품질을 저하시켜 변패를 유발하며, 위생적인 면에서 포자수를 줄이거나 사멸할 필요가 있어서 선택하였다. 병원성 균 중에서 $D_{121.1}$이 0.0065분, z값이 7.8$^{\circ}C$인 Bacillus cereus와 부패현상 관련 균 중에서 $D_{121.1}$이 0.5분, z값이 12$^{\circ}C$인 Bacillus subtilis를 대상으로 해서 개발되었으며, 필요시에는 D값과 z값을 직접 대입하므로서, 여러 가지 미생물에 대해서도 적용이 가능하게 하였다.

• 한국환경과학회지
• /
• 제17권9호
• /
• pp.993-1003
• /
• 2008

Interior space in most buildings is divided into several zones. The most important factors relating to the indoor air environment are temperature, airflow, humidity, and contaminant concentration. An integrated multizone model to predict these environmental factors simultaneously was developed. Also, a computer program for this model was written by the language of VISUAL BASIC. The proposed model was applied to a apartment with five rooms that had been tested by Chung. Comparison of predicted results by this study with measured results by Chung showed that their variations were within 14% for airflow rates, 1% for temperatures, 12% for humidities, and 5% for concentrations. It was seen that the opening operation schedule of building has a significant effect on the air moisture md contaminant removal. Thus, this model may be available for predicting the indoor air environment and may be contributed to design the ventilation plan for controling of indoor air quality.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권5호
• /
• pp.33-41
• /
• 2000

Three dimensional flow fields around passenger car body was computed by PAM-FLOW, well-known and validated computer program for thermal and fluid analysis. Regarding the computational method, a Navier-Stokes solver based on finite element method with various turbulent models and adaptive grid technique (H-refinement)was adopted. The results were physically reasonable and compared with experimental data, giving good agreement. It was found that three dimensional flow simulation with H-refinement technique had potential for prediction of low fie이 around vehicle and the ability to predict vortex in the wake, which is vital for CFD to be used for automobile aerodynamic calculation.

• 설비공학논문집
• /
• 제15권5호
• /
• pp.337-345
• /
• 2003

In the case of heat exchangers operating under frosting condition, the growth of frost layer causes the heat exchanger to increase the thermal resistance and pressure loss of the air flow. In this paper, a transient characteristic prediction model of the heat transfer for multi inverter heat pump with frosting on its surface was presented taking into account the change of the fin efficiency due to the growth of the frost layer. In this dynamic simulation program, which was peformed for a basic air conditioning system model, such as evaporator, condenser, compressor, linear electronic expansion valve (LEV) and bypass circuit. The theoretical model was driven from the obtained heat transfer coefficient and mass transfer coefficient, independently. And we consider heat transfer performance was only affected by a decrease of the wind flow area. The calculated results were compared with some cases of experiments for frosting conditions.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 가을 학술발표회논문집
• /
• pp.11-17
• /
• 2000

,An residual stress and out-of plane deformation produced by butt welding was analyzed by four kinds of 3D-FEM programs(Thermal El-P1 Analysis) developed by authors. The magnitude of deformation of perpendicular to the welding line generated by butt welding was large when the reduced integration method was used. This was because of removal of the locking phenomenon, which it was generally known that the stiffness of the shear component of out-of-plane was largely evaluated. And the magnitude of residual stress was analyzed by using the FEM program based on a large and small deformation theory was similar to that was analyzed by the redeced integration method.

• Journal of Welding and Joining
• /
• 제16권3호
• /
• pp.74-84
• /
• 1998

The microstructures of the HAZ (Heat Affected Zone) are generally different from the base metal due to rapid thermal cycle during welding process. Particuraly, CGHAZ (Coarsened Grain Heat Affected Zone) near the fusion line is the most concerned region in which many metallurgical and mechanical discontinuities have been normally generated. A computer program by the numerical formularization of phase transformation during cooling with different rates was developed to generate the CCT diagram, and to predict microstructural (phase) changes in the CGHAZ. In order to verify simulated results, isothermal and continuous cooling transformation experiments were conducted. The simulated and experimental results showed that the developed computer model could successfully predict the room temperature microstructural changes (changes in volume fraction of phases) under various welding conditions (heat input & cooling rate $(Δt_{8/5})$).

• 대한기계학회논문집A
• /
• 제24권10호
• /
• pp.2654-2663
• /
• 2000

Steam turbine rotors are the most critical and highly stressed components of a steam power plant; therefore, the life expectancy of the turbine rotor is an important consideration for the safety of a steam power plant. The objective of this paper is to develop a life estimation program for turbine rotors for all possible operating conditions. For this purpose, finite element analysis was carried out for four normal operating modes (cold, warm, hot and very hot starts) using ABAQUS codes. The results are made into databases to evaluate the life expenditure for an actual operating condition. For any other possible abnormal operating condition, the operating data are transmitted to the server (workstation) through a network to carry out finite element analysis. Damage estimation is carried out by transmitting the finite element analysis results to the personal computer, and then the life expectancy is calculated.

• 설비공학논문집
• /
• 제11권3호
• /
• pp.391-400
• /
• 1999

The efficiency and capacity of an air source heat pump system decrease as the ambient temperature drops. One strategy of avoiding the decrease of the efficiency and capacity in air source heat pump system is to switch to another thermal energy source. Water can be a good candidate for the heat source. This paper presents the results of the performance analysis of heat pump system with a single unit dual source(SUDS) evaporator The heat exchanger combines two separated evaporators into a single evaporator and the object of the SUDS evaporator is to recover energy from dual heat sources, i.e. air and water. Simulation program is developed for the dual source heat pump system with a SUDS evaporator and experimental data are obtained and compared with the simulation results. Differences in heating capacity and COP are 7% and 8% respectively. Simulation results are in good agreement with the test results. Therefore, the developed program is effectively used for the design and performance prediction of the dual source heat pump system with a SUDS evaporator.