• Nuclear Engineering and Technology
• /
• 제48권5호
• /
• pp.1273-1279
• /
• 2016

Production of iodine-131 by neutron activation of tellurium in tellurium dioxide ($TeO_2$) material requires a target that meets the safety requirements. In a radiopharmaceutical production unit, a new lid for a can was designed, which permits tight sealing of the target by using tungsten inert gaswelding. The leakage rate of all prepared targets was assessed using a helium mass spectrometer. The accepted leakage rate is ${\leq}10^{-4}mbr.L/s$, according to the approved safety report related to iodine-131 production in the TRIGA Mark II research reactor (TRIGA: Training, Research, Isotopes, General Atomics). To confirm the resistance of the new design to the irradiation conditions in the TRIGA Mark II research reactor's central thimble, a study of heat effect on the sealed targets for 7 hours in an oven was conducted and the leakage rates were evaluated. The results show that the tightness of the targets is ensured up to $600^{\circ}C$ with the appearance of deformations on lids beyond $450^{\circ}C$. The study of heat transfer through the target was conducted by adopting a one-dimensional approximation, under consideration of the three transfer modes-convection, conduction, and radiation. The quantities of heat generated by gamma and neutron heating were calculated by a validated computational model for the neutronic simulation of the TRIGA Mark II research reactor using the Monte Carlo N-Particle transport code. Using the heat transfer equations according to the three modes of heat transfer, the thermal study of I-131 production by irradiation of the target in the central thimble showed that the temperatures of materials do not exceed the corresponding melting points. To validate this new design, several targets have been irradiated in the central thimble according to a preplanned irradiation program, going from4 hours of irradiation at a power level of 0.5MWup to 35 hours (7 h/d for 5 days a week) at 1.5MW. The results showthat the irradiated targets are tight because no iodine-131 was released in the atmosphere of the reactor building and in the reactor cooling water of the primary circuit.

• 암석학회지
• /
• 제24권2호
• /
• pp.77-90
• /
• 2015

피션트랙 검출에 의해 고체 및 액체상태 지질물질 내 우라늄을 정밀정량하는 최적기법을 제안하고 그 적용성을 검증하였다. 우라늄 정량은 중성자 조사에 의해 유도시킨 $^{235}U$의 핵분열 흔적을 트랙 디텍터에 기록하여 고배율 현미경 하에서 계수함으로써 이루어진다. 우라늄-친화력이 좋은 암석(예: 화강암, 석탄)을 분말 펠릿시료로 만들어 건식 검출하면, 그다지 높지 않은 우라늄함량(<5 ppm, 즉 ${\mu}g\;g^{-1}$)에서도 빈번하게 함유된 함-우라늄광물에 기인한 트랙 군집현상으로 인해 시료의 전체평균 함량 결정이 쉽지 않았으며, 트랙 균질부와 군집부를 별도로 검토해야 한다. 시료의 균질성이 유지된다면 백운모-Lexan 디텍터에 의한 중복 측정과 여러 차례 중성자 조사에 의한 반복 측정에서 높은 재현성이 확인되었다. 건고 액체시료 경우에 $10^1ppm$ 수준 및 그 이상의 우라늄함량에서 흔히 나타나는 불균질 현상을 극복하기 위해, 진공 석영튜브를 이용한 습식 검출법을 제안한다. 습식 검출에서 우라늄 균질성은 $10^0ppm$ 수준 이하에서 회복되며, 측정하한은 $10^2ppb$ (i.e. $ng\;g^{-1}$) 수준까지 무난한 것으로 입증되었다.

• Nuclear Engineering and Technology
• /
• 제55권6호
• /
• pp.2139-2146
• /
• 2023

During reactor operation, the divertor must withstand unprecedented simultaneous high heat fluxes and high-energy neutron irradiation. The extremely severe service environment of the divertor imposes a huge challenge to the bonding quality of divertor joints, i.e., the joints must withstand thermal, mechanical and neutron loads, as well as cyclic mode of operation. In this paper, potassium-doped tungsten (KW) is selected as the plasma facing material (PFM), oxygen-free copper (OFC) as the interlayer, oxide dispersion strengthened copper (ODS-Cu) alloy as the heat sink material, and reduced activation ferritic/martensitic (RAFM) steel as the structural material. In this study, a vacuum brazing technology is proposed and optimized to bond Cu and ODS-Cu alloy with the silver-free brazing material CuSnTi. The most appropriate brazing parameters are a brazing temperature of 940 ℃ and a holding time of 15 min. High-quality bonding interfaces have been successfully obtained by vacuum brazing technology, and the average shear strength of the as-obtained KW/Cu and ODS-Cu alloy joints is ~268 MPa. And a fabrication route for manufacturing the flat-type divertor target based on brazing technology is set. For evaluating the reliability of the fabrication technologies under the reactor relevant condition, the high heat flux test at 20 MW/m² for the as-manufactured flat-type KW/Cu/ODS-Cu/RAFM mockup is carried out by using the Electron-beam Material testing Scenario (EMS-60) with water cooling. This paper reports the improved vacuum brazing technology to connect Cu to ODS-Cu alloy and summarizes the production route, high heat flux (HHF) test, the pre and post non-destructive examination, and the surface results of the flat-type KW/Cu/ODS-Cu/RAFM mockup after the HHF test. The test results demonstrate that the mockup manufactured according to the fabrication route still have structural and interfacial integrity under cyclic high heat loads.

• 헤리티지:역사와 과학
• /
• 제45권3호
• /
• pp.160-173
• /
• 2012

본 연구는 동대문운동장에서 출토된 조선시대 기와의 선후관계, 유물제작기법 및 기술적 속성을 파악하기 위하여 기와의 물리적 화학적 특성 연구를 실시하였다. 기와의 물리적 특성 연구를 위해 흡수율, 비중, 전암대자율, 시차열분석을 실시하였으며, 화학적 특성 연구를 위해 중성자 방사화분석(NAA), 미세조직관찰, X-선 회절분석(XRD) 등을 실시하였다. 기와편 22점의 중성자방사화분석 및 통계분석결과 각각 기와시료는 다른 시대에 서로 다른 제작지에서 생산된 것으로 뚜렷하게 구분되었다. 또한 희토류원소의 출토지별 평균값을 비교해 보아도 각각 서로 다른 조성의 차이를 보이는데 이는 산지가 다른 점토광물을 이용하여 제작하였다는 것을 의미한다. XRD 및 편광현미경 관찰결과 기와의 주요 성분은 석영과 장석이었으며 부분적으로 운모와 일라이트(Illite)가 나타났다. XRD 분석결과 $1000^{\circ}C$의 부근에서 소성되었을 때 나타나는 뮬라이트(mullite)광물 조성이 나타났으며, 시차열분석에서는 $900^{\circ}C$ 부근에서 완만한 발열피크가 나타났다. 이를 토대로 기와의 소성온도를 추정한 결과, 기와는 $900{\sim}1000^{\circ}C$에서 소성이 이루어진 것으로 보인다. 전암대자율 평균값으로 비교분석하였을 때 출토지별 분류는 나타나지 않았지만 문양이 파상문, 태상문, 어골문, 격자문, 횡선문인 경우 0.2~0.78(${\times}103$ SI unit)의 낮은 전암 대자율이 나타나는 특징이 있다. 전체 흡수율은 대체적으로 14%~21% 범위를 보였으며 이는 조선시대 전통기와에서 나타나는 흡수율 14~18%와 유사한 범위를 보이고 있다. 기와시료의 비중은 대체적으로 1.4~2.5g/cm3의 범위를 보여 출토지에 따른 비중 차이가 나타나지 않았다.

• 한국세라믹학회지
• /
• 제51권5호
• /
• pp.418-423
• /
• 2014

Fully ceramic micro encapsulated (FCM) nuclear fuel is a concept recently proposed for enhancing the stability of nuclear fuel. FCM nuclear fuel consists of tristructural-isotropic (TRISO) fuel particles within a SiC matrix. Each TRISO fuel particle is composed of a $UO_2$ kernel and a PyC/SiC/PyC tri-layer which protects the kernel. The SiC ceramic matrix is created by sintering. In this FCM fuel concept, fission products are protected twice, by the TRISO coating layer and by the SiC ceramic. The SiC ceramic has proven attractive for fuel applications owing to its low neutron-absorption cross-section, excellent irradiation resistivity, and high thermal conductivity. In this study, a SiC-matrix composite containing TRISO particles was sintered by hot pressing with $Al_2O_3-Y_2O_3$ additive system. Various sintering conditions were investigated to obtain a relative density greater than 95%. The internal distribution of TRISO particles within the SiC-matrix composite was observed using an x-ray radiograph. The fracture of the TRISO particles was investigated by means of analysis of the cross-section of the SiC-matrix composite.

• Corrosion Science and Technology
• /
• 제13권5호
• /
• pp.178-185
• /
• 2014

Alloy 617 is considered as a candidate Ni-based superalloy for the intermediate heat exchanger (IHX) of a very high-temperature gas reactor (VHTR) because of its good creep strength and corrosion resistance at high temperatures. Helium is used as a coolant in a VHTR owing to its high thermal conductivity, inertness, and low neutron absorption. However, helium inevitably includes impurities that create an imbalance in the surface reactivity at the interface of the coolant and the exposed materials. As the Alloy 617 has been exposed to high temperatures at $950^{\circ}C$ in the impure helium environment of a VHTR, the degradation of material is accelerated and mechanical properties decreased. The high-temperature strength, creep, and corrosion properties of the structural material for an IHX are highly important to maintain the integrity in a harsh environment for a 60 year period. Therefore, an alloy superior to alloy 617 should be developed. In this study, the mechanical and high-temperature corrosion properties for Ni-Cr alloys fabricated in the laboratory were evaluated as a function of the grain boundary strengthening and alloying elements. The ductility increased and decreased by increasing the amount of Mo and Cr, respectively. Surface oxide was detached during the corrosion test, when Al was not added to alloy. However the alloy with Al showed improved oxide adhesive property without significant degradation and mechanical property. Aluminum seems to act as an anti-corrosive role in the Ni-based alloy.

• Journal of Nutrition and Health
• /
• 제31권2호
• /
• pp.206-212
• /
• 1998

This study was undertaken to analyze the iodine content in commonly donsumed Korean foods. Food samples were purchased from 3 randomly selected markets. The iodine contents in foods were determined by nuetron activation analysis (NAA). All irradiation of food samples were done at a pnueumatic transfer system (thermal nuetron flux : 1 $\times$1013n/$\textrm{cm}^2$.s) of the TRIGA MarkIII research reactor in the Korea Atomic Energy Research Institute . The results indicated that the iodine content was high in seaweeds, fishes, and iodine-enriched eggs in that order and very low in grain, beans , fruits and vegetables. Edible seaweeds contained iodine levels of between 13,700 and 1,790, 600$\mu\textrm{g}$/kg. Levels of iodine in fishes and shellfishes were between 478 and 2, 840$\mu\textrm{g}$/kg. Ordinary eggs contained 314$\mu\textrm{g}$/kg iodine, but iodine -enriched eggs contained 1,869$\mu\textrm{g}$/kg. The average concentration of iodine in milk was 207$\mu\textrm{g}$/kg. There was seasonal variation in the iodine content of milk , levels were highest in winter milk(230$\mu\textrm{g}$/kg) and lowest in summer milk(180$\mu\textrm{g}$/kg).The idodine contents of most vegetables and fruits were below 10$\mu\textrm{g}$/kg. The iodine contents of most vegetables and fruits were below 10$\mu\textrm{g}$/kg. From high to low , the sequence of foods with high iodine content in one serving was as follows ; sea tangle , sea mustard, iodine-enriched eggs, fish , laver and milk. This study may provide basic data on the iodine content of foods consumed by Korean which have not yet been analyzed .

• Nuclear Engineering and Technology
• /
• 제52권4호
• /
• pp.661-673
• /
• 2020

The quarter-core simulation of BEAVRS Cycle 2 depletion benchmark has been conducted using the MCS/CTF coupling system. MCS/CTF is a cycle-wise Picard iteration based inner-coupling code system, which couples sub-channel T/H (thermal/hydraulic) code CTF as a T/H solver in Monte Carlo neutron transport code MCS. This coupling code system has been previously applied in the BEAVRS benchmark Cycle 1 full-core simulation. The Cycle 2 depletion has been performed with T/H feedback based on the spent fuel materials composition pre-generated by the Cycle 1 depletion simulation using refueling capability of MCS code. Meanwhile, the MCS internal one-dimension T/H solver (MCS/TH1D) has been also applied in the simulation as the reference. In this paper, an analysis of the detailed criticality boron concentration and the axially integrated assembly-wise detector signals will be presented and compared with measured data based on the real operating physical conditions. Moreover, the MCS/CTF simulated results for neutronics and T/H parameters will be also compared to MCS/TH1D to figure out their difference, which proves the practical application of MCS into the BEAVRS benchmark two-cycle depletion simulations.

• Nuclear Engineering and Technology
• /
• 제23권3호
• /
• pp.352-362
• /
• 1991

가압 경수로의 노심 설계에 있어서 제한된 우라늄 자원의 효율적인 이용을 위한 다양한 방안으로 장주기 운전, 고연소도 및 저누출 장전 모형 통을 강구하고 있는 추세이다. 이러한 노심들은 원자로 운전 주기 전반에 걸친 공간적 출력 분포 제어와 잉여 반응도 제어를 위해 가연성 독물질을 사용하고 있다. 이와 관련하여 가연성 독물질 관리의 최적화 연구가 다각도로 진행되고 있다. 본 연구에서는 1990년도부터 국내 가압 경수로에 국산 핵연료가 장전되기 시작하면서 가도리니아 독봉을 사용하고 있으며 장차 주된 가연성 독물질로 쓰일 예정이므로 이에 대해서 분석을 수행하였다. 분석 결과 가도리니아 독봉은 열중성자 흡수 단면적이 매우 큰데서 기인한 특이한 연소 특성을 보이고 있다. 특히 집합체 내에서의 가도리니아 독봉의 위치에 따라 매우 다양한 출력 분포를 보이고 있다. 이러한 다양한 출력 분포 중에서 노심의 반경 방향 첨두 출력을 가능한 낮게하는 집합체 내에서의 가도리니아봉 위치 최적 선정을 위한 방법론을 제시하였다.

• Nuclear Engineering and Technology
• /
• 제43권3호
• /
• pp.301-308
• /
• 2011

The diametral creep of pressure tubes (PTs) in CANDU (CANada Deuterium Uranium) reactors is one of the principal aging mechanisms governing the heat transfer and hydraulic degradation of the heat transport system (HTS). PT diametral creep leads to diametral expansion, which affects the thermal hydraulic characteristics of the coolant channels and the critical heat flux (CHF). The CHF is a major parameter determining the critical channel power (CCP), which is used in the trip setpoint calculations of regional overpower protection (ROP) systems. Therefore, it is essential to predict PT diametral creep in CANDU reactors. PT diametral creep is caused mainly by fast neutron irradiation, temperature and applied stress. The objective of this study was to develop a bundle position-wise linear model (BPLM) to predict PT diametral creep employing previously measured PT diameters and HTS operating conditions. The linear model was optimized using a genetic algorithm and was devised based on a bundle position because it is expected that each bundle position in a PT channel has inherent characteristics. The proposed BPLM for predicting PT diametral creep was confirmed using the operating data of the Wolsung nuclear power plant in Korea. The linear model was able to predict PT diametral creep accurately.