• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.9
• /
• pp.90-97
• /
• 2002

Ceramics are being increasingly used in industry due to their outstanding physical and chemical properties. But these materials are difficult to machine by traditional machining processes, because they are hard and brittle. Recently, as one of various alternative processes, laser-beam machining is widely used in the cutting of ceramics. Although the use of lasers presents a number of advantages over other methods, one of the problems associated with this process is the uncertain formation of cracks that result from the thermal stresses. This paper presents a Bayesian probabilistic modeling of crack formation over thin alumina plates during laser cutting.

• 한국연소학회:학술대회논문집
• /
• 1998.10a
• /
• pp.165-170
• /
• 1998

Turbulent nonpremixed $H_2$-air jet flames are numerically investigated using the joint PDF model. The reaction progress variable is derived by assuming the radicals 0, H, and OH to be in partial equilibrium and additional species $HO_2$ and $H_2O_2$ in steady state. The model is extended to npnadiabatic flame by introducing additional variable for the transport of enthalpy and radiative source term is calculated using a local, geometry independent model. In terms of flame structure and NO formation, the predicted results are favorably agreed with experimental data. The effects of nonequilibrium chemistry and radiative heat loss on the thermal NO formation are discussed in detail.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.3
• /
• pp.377-383
• /
• 1999

In this study, the behavior of frost formation according to surface characteristics in the fin-tube heat exchanger has been examined experimentally. The results show that the thickness of the frost which is attached to the hydrophilic heat exchanger becomes thin and the air pressure drop is smaller than that of bare aluminium heat exchanger However, the frost mass of hydrophilic heat exchanger is more than the bare one. Hence, high density frost is attached to hydrophilic heat exchanger. The sensible and latent heat flux of hydrophilic heat exchanger is bigger than that of bare one, but the increasing amount is very small and the improvement of thermal performance is also very small. The variation of fin-pitch of heat exchanger shows little influence on frost formation and hydrophilic heat exchanger loses its surface characteristics rapidly with increasing relative humidity.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.1
• /
• pp.33.1-33.1
• /
• 2019

Protostars grow their mass by the accretion of disk material, which is infalling from the envelope. This accretion process is important to the physical and chemical conditions of the disk and envelope, and thus, the planets yet to be formed from the disk material. Therefore, if we map the physical and chemical properties of disks and envelopes, we can study indirectly the accretion process in star formation. In particular, the chemical distribution in the disk and the inner envelope of a young stellar object is greatly affected by the thermal history, which is mainly determined by the accretion process in the system. In my talk, I will review the episodic accretion model for the low mass star formation and observational efforts to find the evidence of episodic accretion. Finally, I will present our recent ALMA detection of several complex organic molecules associated directly with the planet formation in V883 Ori, which is in the burst accretion phase.

• Journal of the Mineralogical Society of Korea
• /
• v.12 no.1
• /
• pp.11-22
• /
• 1999

Thermal behavior of dickite was studied by thermal analysis, X-ray diffraction analysis, electron microprobe analysis, and scanning electron microscopy, Dickite has an endothermic peak at about$ 650^{\circ}C$ and an exothermic one at $960^{\circ}C$ in the differential thermal analysis. The endothermic reaction is assigned to the decomposition of dickite to meta-dickite. Hydroxyl radicals are removed from dickite structure by the reaction, resulting in the weight loss about 10.5~14.5% and appearance of a 14$\AA$ phase different from other kaolin minerals. The reaction slowly proceed in the range of $200^{\circ}C$. As the completion of decomposition, aciclular mullite forms at the expense of meta-dickite plates with random crystallographic relationship. Mullites have diverse silica versus alumina ratio. The exothermic reaction without weight loss seems to be due to the formation of spinel and amorphous silica. The spinel phase shows cryptocrystalline globular morphology accompanying a little amount of silica. From spinel phase shows cryptocrystalling globular morphology accompanying a little amount of silica. From this work, it is suggested that mullite is formed from meta-dickite much lower temperature than the reported one in the previous works.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.77-82
• /
• 2005

In previous paper, the wear properties of clutch facing materials with two different copper amounts against fly-wheel materials used in the clutch system were investigated by sliding wear tests at different applied loads and speeds. This paper have been aimed to evaluate the friction properties for clutch facing materials at the same test conditions as the previous paper. The experimental results indicated that the friction properties of clutch facing materials are influenced from the thermal conductivities of the clutch facing material and the counter material. The clutch facing material with the lower thermal conductivity and the fly-wheel material with the higher thermal conductivity showed the low and stable friction coefficient in the range of high sliding speed. This appears to be due to the formation of a film on the surface of the fly-wheel material.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.67-75
• /
• 1998

This study aimed at he experimental and finite element analytic investigation of the effect of preheating on he residual stress of weldment. In this study, an autogenous arc welding was used on type 304 stainless steel and MARC as F.E.M. common code was utilized in analysis The analyses include transient and moving heat source and thermal properties as function of temperature. During welding, the thermal cycles of four locations in the weldment were recorded to investigate of the behavior of thermal stress and residual stress. The experimental and analytic results had good coincidence and show that there are two factors influencing the formation of welding residual stress in preheat process. One is the elevation of welding equilibrium temperature and the other is the increase of amount of heat input. The former decrease welding residual stress and the latter increase welding residual stress. Therefore, the cumulative effects result in the welding residual stress not being improved significantly with preheating in 304 stainless steel.

• Journal of the Korean Ceramic Society
• /
• v.30 no.2
• /
• pp.93-100
• /
• 1993

The effects of MgO addition on thermal expansiion coefficient and dielectric constant of mullite were studied. Thermal coefficient and dielectric constant decrease with increasing MgO content and exhibit a minimum value at 1wt% MgO. However, above 3wt% MgO content both values increase. Result of X-ray diffraction analysis how that mullite compositions which include more than 0.1wt% MgO form cordierite. Spinel is also formed as well as cordierite in the composition containing more than 3wt% MgO. The results indicate that addition of MgO affect the thermal expansion coefficient and dielectric constant of mullite substrate because of the formation of new phases; cordierite and spinel. The thermal expansion coefficient and dielectric constant are affected mainly by cordierite and spinel in the regions containing less than more than 3wt% MgO, respectively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.11
• /
• pp.1597-1604
• /
• 2002

In this study, numerical investigation has been performed on the impingement, spreading and solidification of a coating material droplet impacting onto a solid substrate in the thermal spray process. The numerical model is validated through the comparison of the present numerical result with experimental data fer the flat substrate without surface defects. An analysis of deposition formation on the non-polished substrate with surface defects is also performed. The parametric study is conducted with various surface defect sizes and shapes to examine the effect of surface defects on the impact and solidification of the liquid droplet on the substrate.

• Macromolecular Research
• /
• v.11 no.3
• /
• pp.178-182
• /
• 2003

The thermal decomposition of phthalate alone and with poly(vinyl chloride) (PVC) was carried out under a nitrogen atmosphere in a 4-necked separable flask. The thermal decomposition of phthalate in the presence of PVC began at 150$^{\circ}$, about 10$0^{\circ}C$ lower than the decomposition of phthalate alone. The formation of octyl chloride indicated an interaction reaction between phthalate and PVC. From the analysis of the composition of commercially plasticized PVC sheet (film and board), the phthalates (dibutyl phthalate, dihexyl phthalate) and di(2-ethylhexyl) phthalate), 2-ethyl-1-hexanol, phthalic anhydride, and 2-ethylhexyl hydrogen phthalate were identified. The mutage-nicities of these decomposition products were higher than those of phthalic diesters (phthalates).