• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.951-961
• /
• 2001

The present article presents an extension to the computational model for spray/wall interaction and liquid film processes that has been dealt with in the earlier studies (Lee and Ryou, 2000a). The extensions incorporate film spread due to impingement forces and dynamic motion induced by film inertia to predict the dynamic characteristics of wall films effectively. The film model includes the impingement pressure of droplets, tangential momentum transfer due to the impinging droplets on the film surface and the gas shear force at the film surface. Validation of the spray/wall interaction model and the film model was carried out for non-evaporative diesel sprays against several sources of experimental data. The computational model for spray/wall interactions was in good agreement with experimental data for both spray radius and height. The film model in the present work was better than the previous static film model, indicating that the dynamic effects of film motion should be considered for wall films. On the overall the present film model was acceptable for predication of the film radius and thickness.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1562-1572
• /
• 1996

The rigid-plastic finite element formulation including the inertia force is derived and then the rigid-plastic finite elemnt program considering the inertia effect is developed. In order to consider the strain hardening, strain rate hardening and thermal softening effects which are frequentrly observed in high-velocity deformation phenomena, the Johnson-Cook constitutive odel is applied. The developed program is used to simulate two high-velocity deformation problemss ; rod impact test and hdigh-velocity compression precess. As a result of rod impact test simulation, it is found that the siulated result has a good agreement with the experimental observation. Through the high-velocity compression process simulation. it is also found that the accuracy of the simulated results is dependent upon the time increment size and mesh size.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1232-1240
• /
• 2002

Recently, linear motors are applied to many small precision products. Thus high generating power with small size is required of it. In order to increase the motor efficiency, the design variables need to be optimized. In this study, Vector Fields FEM software, OPERA-3d, was used for simulating linear motor. The thrust and magnetic flux density at the air-gap center were simulated and compared with the experimental results. Taguchi method was applied to investigate the effects of each variables. As a result, the thickness of conductor and magnet was important for the thrust but the thickness of the yoke. The temperature of the conductor was determined by finding the thermal conductivity that was determined by experimentation. Correlation equation relating to the thrust and temperature was proposed by Latin square and Least Square method. The optimum design variables were determined by correlation equation, and compared with simulation results. According to this analysis, thrust force of linear motor was improved about 7% comparing with conventional model.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.3 no.1
• /
• pp.7-14
• /
• 2004

Machining error is defined the normal distance between designed surface and actual tool path with tool deflection. This is inevitably caused by the tool deflection, tool wear, thermal effect and machine tool errors and so on. Among these factors, tool deflection is usually known as the most significant factor of machining error. Tool deflection problem is analyzed using Instantaneous horizontal cutting forces. The high quality and precision of machining products are required in finishing. In order to achieve these purposes, it is necessary work that decrease the machining error. This paper presents a study on the machining error caused by the tool deflection in ball end milling of 2 dimensional surface. Tool deflection model and simple machining error prediction model are described. This model is checked the validity with machining experiments of 2 dimensional surface. These results may be used to decrease machining error and tool path decision.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.365-368
• /
• 2002

The design of industrial arc plasma systems is still largely based on trial and error although the situation is rapidly improving because of the available computational power at a cost which is still fast coming down. The desire to predict the behavior of arc plasma system, thus reducing the development cost, has been the motivation of arc research. To interrupt fault current, the most enormous duty of a circuit breaker, is achieved by separating two contacts in a interruption medium, $SF_{6}$ gas or air etc., and arc plasma is inevitably established between the contacts. The arc must be controlled and interrupted at an appropriate current zero. In order to analyze arc behavior in $SF_{6}$ gas circuit breakers, a numerical calculation method combined with flow field and electromagnetic field has been developed. The method has been applied to model arc generated in the Aachen nozzle and compared the results with the experimental results. Next, we have simulated the unsteady flow characteristics to be induced by arcing of AC cycle, and conformed that the method can predict arc behavior in account of thermal transport to $SF_{6}$ gas around the arc, such as increase of arc voltage near current zero and dependency of arc radius on arc current to maintain constant arc current density.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.2
• /
• pp.241-246
• /
• 2013

This paper reports fabrication and characterization of cellulose Electro-Active Paper (EAPap) with increased thickness. Usual thickness of cellulose EAPap was $15{\mu}m$. This thickness needs to be increased to enhance the mechanical force output of EAPap. To fabricate thick cellulose EAPap, the fabrication process parameters including casting and drying processes should be investigated. In this paper, the casting thickness is increased from $800{\mu}m$ to $1500{\mu}m$, and heating times on a hot plate before and after curing process are introduced at 40 and $60^{\circ}C$ for 30 and 60 minutes, respectively. Thickness measurement, Thermal Gravitational Analysis (TGA), UV-transmittance, Young's modulus, and piezoelectric charge constant are measured. Heated EAPaps with increased thickness have similar TGA result, higher transmittance, higher Young's modulus and lower piezoelectric charge constant.

• Korean journal of food and cookery science
• /
• v.10 no.2
• /
• pp.146-150
• /
• 1994

The addition of nonfish protein significantly reduced the strength of nonfish protein-incorporated surimi gel in terms of cohesiveness, rigidity and shear force. The sensory textural properties of fiberi-3ed surimi gel product was characterized as the reduction in intensity of undesirable rubberiness, chewiness and firmness, thus increasing the desirability in over all texture. Gel strength of both cohesiveness and rigidity of nonfish protein was inversely correlated with those of nonfish protein-incorporated surimi gel. The variation of texture-modifying properties of nonfish protein in surimi gel was attributed to the differences in thermal hydration and gelation properties of nonfish protein.

• Coupled systems mechanics
• /
• v.7 no.4
• /
• pp.373-393
• /
• 2018

This paper is concerned with the wave propagation behavior of rotating functionally graded temperature-dependent nanoscale beams subjected to thermal loading based on nonlocal strain gradient stress field. Uniform, linear and nonlinear temperature distributions across the thickness are investigated. Thermo-elastic properties of FG beam change gradually according to the Mori-Tanaka distribution model in the spatial coordinate. The nanobeam is modeled via a higher-order shear deformable refined beam theory which has a trigonometric shear stress function. The governing equations are derived by Hamilton's principle as a function of axial force due to centrifugal stiffening and displacement. By applying an analytical solution and solving an eigenvalue problem, the dispersion relations of rotating FG nanobeam are obtained. Numerical results illustrate that various parameters including temperature change, angular velocity, nonlocality parameter, wave number and gradient index have significant effect on the wave dispersion characteristics of the understudy nanobeam. The outcome of this study can provide beneficial information for the next generation researches and exact design of nano-machines including nanoscale molecular bearings and nanogears, etc.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.331-336
• /
• 2012

Nowaday the conventional solar collector material prices are rising up because of pricy metal material over the world. The solar collector is too expensive to recycle to save the earth. Advanced polymer research is founded a high thermal resistant polymer and also it has high sun energy transmission. It also has cheaper material and easy manufacturing process, compare with conventional solar collector material. This paper is focussing on glazing simulation of polymer solar collector against wind pressure. The modeling geometry of polymer solar glazing are purposed by single layer, double layer hollow, zig-zag and tower. A simulation by using the Finite Volume was conducted to get Factor of Safety (FoS). The purpose of this paper is to find the best polymer glazing design, which can be as reference for the solar collector company to build Polymer. Hope fully new model of polymer solar collector has cheap, light, high sun energy transmitter, easy to be made and strong against wind force characteristics.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06b
• /
• pp.35-47
• /
• 1989

누설방지를 목적으로 산업용 기계에서 많이 사용되고 있는 기계평면시일(mechanical face seal)은 기능상 높은 신뢰도를 요구하고 있다. 이를 위하여 동적 안정성이 커야되고, 밀봉된 유체의 누설을 최소화시킬 수 있는 정도에서 시일의 수명을 결정해야 한다. 이와같이 상반된 성질을 동시에 만족시키기 위하여 시일 성능에 영향을 미칠 수 있는 기하학적 요인들을 고려하여 해석해야 한다. 일반적으로 미끄럼 접촉운동을 하고 있는 시일에서 시일링 간극(sealing gap)이 수 micron 단위라는 점을 고려할때 시일 조립시 중심맞추기(alignnment) 정미\ulcorner 결여 및 회전축의 자중량 등에 의한 기계적 변형(mechanical distortion), 특히 고온의 분위기에서 작동되고 있는 시일의 열변형(thermal distortion)은 시일의 경사집에 커다란 영햐을 주고 있다. 또한 누설을 최소화시킬 목적으로 시일 링(seal ring) 을 시일의 경사짐에 커다란 영향을 주고 있는 스프링의 강성도를 증가시키면 상대 미끄럼 운동을 하고 있는 접촉명이 건조마찰에 의한 마멸이 진행되어 코닝(coning)현상이 생긴다. 시일 평면에서 코닝 현상은 시일의 축방향 분리력(axial separtating force)과 경사 모우면트(tilting moment)에 커다란 영향을 주고 있는 것으로 알여졌다. 이들의 연구는 주로 경사진 시일평판에 시일근사치이논(seal approximation bhoryl)을 이용하여 1차원 비압축성에 관한 시월 성능을 해석하였다. 본 연구에서는 비압축성 유체의 점성이 온도에 의하여 변화를 일으키는 조건하에서 경사진 회전시일에 코닝이 발생되었을때 시일링 각극에서의 압력분포를 ㅈ차원인 경우에 대하여 수치적으로 해석을 하였다.