• The KSFM Journal of Fluid Machinery
• /
• v.17 no.1
• /
• pp.41-46
• /
• 2014

The thermal-flow characteristics of screw compressor were numerically investigated with various geometrical configurations of its coolant flow passage applied to the separate block for enhancing the heat transfer performance of it. The length ratio($L_s/D$=4.8, 5.6, 6.4) and thickness ratio(t/D=0.2, 0.4, 0.6) of the separate block in the flow passage of the water jacket were adopted to design parameters. Results showed that the pressure drop and heat transfer were increased as the length of separate block increases due to the flow separation and centrifugal force. The results were graphically depicted with various flow and geometrical conditions.

• Journal of the Korea Society for Simulation
• /
• v.13 no.2
• /
• pp.13-21
• /
• 2004

The thermal-hydraulic model ARTS which was based on the RETRAN-3D code adopted in the domestic full-scope power plant simulator which was provided in 1998 by KEPRI. Since ARTS is a generalized code to model the components with control volumes, the smaller time-step size should be used even if converged solution could not get in a single volume. Therefore, dedicated models which do not force to reduce the time-step size are sometimes more suitable in terms of a real-time calculation and robustness. In the case of PRT(Pressurizer Relief Tank) model, it is consist of subcooled water in bottom and non-condensable gas in top. The sparger merged under subcooled water enhances condensation. The complicated thermal-hydraulic phenomena such as condensation, phase separation with existence of non-condensable gas makes difficult to simulate. Therefore, the PRT volume can limit the time-step size if we model it with a general control volume. To prevent the time-step size reduction due to convergence failure for simulating this component, we developed a dedicated model for PRT. The dedicated model was expected to provide substantially more accurate predictions in the analysis of the system transients. The results were resonable in terms of accuracy, real-time simulation, robustness and education of operators, complying with the ANSI/ANS-3.5-1998 simulator software performance criteria and RETRAN-3D results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.227-227
• /
• 2008

CdS is II-VI semiconductor with a wide band gap of approximately 2.42 eV. CdS is the most popularly employed heterojunction partner to p-CdTe due to its similar chemical properties. The as-deposited films are annealed in Rapid Thermal Annealing (RTA) system in various atmosphere(Air, Vacuum and $N_2$) at $500^{\circ}C$. In this work, X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) of chemical bath deposited (CBD) CdS films on glass is carried out. In case of the annealed CdS films in $N_2$, grain size was larger than as-annealed films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.395-396
• /
• 2008

Copper-Phthalocyanine (Cu-Pc) thin films of 100nm thickness have been deposited on silicon substrates as the different heating temperatures by thermal evaporation deposition technique. X-ray patterns showed with different temperature conditions at the $2\theta$ range of 5-$55^{\circ}$. The surface roughness of Cu-Pc thin films was investigated by using an atomic force microscope (AFM). A scanning electron microscope (SEM) has been used to characterize the micro-structures and morphologies depended on the substrate temperatures.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.154-161
• /
• 2007

Hot spot phenomenon that occurs, during judder vibration, is locally concentrated heat due to friction between brake disk and pad. It is important to understand the reason behind hot spot phenomenon, for reduction of judder vibration. In this experimental study, experiments were performed in accordance with rotation speed of brake disk, pressure of master cylinder and pad length for achieving different aspects of hot spot phenomenon. Temperature distribution of hot spot was obtained by using the infrared camera. As the hot spot occurred, vibration was measured and frequency analysis was performed. Finite element analysis of thermal deformation of disk was performed by using temperature distribution that was achieved by experimental results. And mode shapes of disk was analyzed by finite element analysis and compared with experimental results. It was observed that the excitation frequency band of frictional contact and frictional force mainly affects the hot spot phenomenon.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1291-1292
• /
• 2007

Recently, there were many researches for efficiency improvement of DSC. Among of these works, research of surface treatment is still a prerequisite for electron diffusion, light-harvesting and surface state of DSC.[1] Using of the surface treatment, it can be raise up porosity of $TiO_2$ nano-crystalline structure on photo-electrode. There are chemical, physical, electrical and optical methods which raise up its porosity. In this paper, we have designed and manufactured MOPA-type ultrasonic circuit (100W, frequency and duty variable). Manufactured ultrasonic circuit to use to force cavity density and power into $TiO_2$ paste. Then, we have optimized forcing time, frequency and duty of ultrasonic irradiation for surface treatment of photo-electrode of DSC. In I-V characteristic test of DSC, ultrasonic and thermal treated DSC shows 19% improved its efficiency against monolithic DSC. And it shows stability of light-harvesting from drastically change of light irradiation test.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.5
• /
• pp.202-205
• /
• 2008

We have studied the liquid crystal (LC) orientation behavior on the organic hybrid overcoat layer with ion beam irradiation. Excellent LC alignments of the nematic liquid crystal (NLC) on the ion beam irradiated organic hybrid overcoat layers were observed in various intensities above 600 eV. Pretilt angles of the NLC on the organic hybrid overcoat layers for all ion beam energy intensities were observed from 0.2 to 0.5 degrees. Also, we used the atomic force microscopy (AFM) images for measuring the roughness of the organic hybrid overcoat layers with ion beam irradiation before and after. The surface of organic hybrid overcoat layers was leveled off by the ion beam irradiation. Finally, a good LC alignment thermal stability on the organic hybrid overcoat layer with ion beam irradiation can be achieved.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.143.2-143.2
• /
• 2013

Nanomechanical and electrical properties of vanadium dioxide (VO2) thin films across thermal-driven phase transition are investigated with ultra-high vacuum atomic force microscopy. VO2 thin films have been deposited on the n-type heavily doped silicon wafer by pulsed laser deposition. X-ray diffraction reveals that it is textured polycrystalline with preferential orientation of (100) and (120) planes in monoclinic phase. As the temperature increases, the friction decreased at the temperature below the transition temperature, and then the friction increased as increasing temperature above the transition temperature. We attribute this observation to the combined effect of the thermal lubricity and electronic contribution in friction. Furthermore, the dependence of nanoscale conductance on the local pressure was indicated at the various temperatures, and the result was discussed in the view of pressure-induced metal-insulator transition.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.397-404
• /
• 2006

Effects of surface defect distribution on flame instability during flame-surface interaction are experimentally investigated. To examine chemical quenching phenomenon which is caused by radical adsorption and recombination processes on the surface, thermally grown silicon oxide plates with well-defined defect density were prepared. ion implantation technique was used to control the number of defects, i.e. oxygen vacancies. In an attempt to preferentially remove oxygen atoms from silicon dioxide surface, argon ions with low energy level from 3keV to 5keV were irradiated at the incident angle of $60^{\circ}$. Compositional and structural modification of $SiO_2$ induced by low-energy $Ar^+$ ion irradiation has been characterized by Atomic Force Microscopy (AFM) and X-ray Photoelectron Spectroscopy (XPS). It has been found that as the ion energy is increased, the number of structural defect is also increased and non-stoichiometric condition of $SiO_x({\le}2)$ is enhanced.

• Fire Science and Engineering
• /
• v.18 no.2
• /
• pp.73-78
• /
• 2004

This study investigated about smoke/heat interception screen that can protect underneath of fire door and floor when occur fire, and keep out leakage or diffusion of smoke/heat. In this study, to considered differential pressure form smoke control area and mechanical force by fluid buoyancy of smoke when occur fire and stream of heat, are analyzed to used $ANSYS^{\circledR}$ of finite element analysis code. It presented direction of optimal design of smoke/heat interception screens that can minimize loading condition from study results, and helped that construct basic engineering data of smoke/heat interception systems as that utilize its shape design of smoke/heat interception screens.