• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1453-1456
• /
• 2009

Transparent sol-gel hybrid dielectric material (hybrimer) coating films were fabricated by spin coating and photo or thermal curing of sol-gel derived oligosiloxane resins. Hybrimer coating films are suitable as the passivation layer of TFT in AMLCD due to low dielectric constant, small loss tangent, low leakage current density, high transmittance and thermal stability.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.4
• /
• pp.326-331
• /
• 1995

Poly(enaryloxynitriles) containing Schiff bases were prepared from p-bis(1-chloro-2,2-dicyanovinyl)benzene (2) and various aromatic diols having Schiff base moiety by interfacial polymerization. The chemical structure of the polymers was confirmed through synthesis of their corresponding model compounds. All the polymers were soluble in polar aprotic solvents and their brittle films were cast from DMF solution. They showed a large exotherm around 340 ℃ attributable to the chemical change of dicyanovinyl group. Especially, curing of azomethine group was observed to occur at 390 ℃ by differential scanning calorimetry. According to the thermogravimetric analyses, they exhibited excellent thermal stability with 60-90% residual weight at 500 ℃ in nitrogen.

• Membrane Journal
• /
• v.14 no.3
• /
• pp.207-217
• /
• 2004

In this study, we prepared nanofiltration membrane by applying the interfacial polymerization method as a way of manufacturing composite membranes. We have examined the effects of various preparation factors such as monomer concentration and composition, thermal curing condition, post treatment condition. In addition to preparation conditions, we also monitored the effects of operation conditions such as feed solution concentration and operation pressure on the permeation properties of the resulting nanofiltration membrane. We intended to increase the permeation rate of nanofiltration membrane by the enlargement of effective surface area using additives during interfacial polymerization step. With increasing the monomer concentration, membrane permeation rate are decreased with maintaining almost constant rejection. With respect to curing condition, with increasing the curing temperature both permeation rate and rejection are decreased. With increasing the ratio of MPD in amino monomer composition, permeation rate decreased drastically with high rejection. With increasing the feed solution concentration, both permeation rate and rejection decreased. Both permeation rates and rejection increased with increasing the operating pressure. Nanofiltration membrane have higher surface roughness with increasing additive concentration in the case of using MPD contained amine composition than using piperazine alone. Permeation rates are much lower than the nanofiltration membrane prepared by piperazine.

• Korean Chemical Engineering Research
• /
• v.43 no.3
• /
• pp.393-400
• /
• 2005

A novel evaluation method was investigated for measuring the ability of acid amplification of acid amplifier. The method was based on the measurement of conductivity change by the acid generation according to UV radiation. It was found that the decrease of conductivity was caused by photopolymerization of epoxy monomer during UV curing process of ink film and by the rate of UV curing. In this paper, the novel acid amplifiers were synthesized and measured thermal stability by means of DSC. It was found that mono-type acid amplifiers were more stable than di-type. It was possible to make the dynamical evaluation of the curing rate of UV curable ink in curing process by this method.

• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.690-696
• /
• 2019

Geopolymer is an alumina silicate-based ceramic material that has good heat-resistance and fire-resistance; it can be cured at room temperature, and thus its manufacturing process is simple. Geopolymer can be used as a reinforcement or floor finish for high-speed curing applications. In this manuscript, we investigate a high-speed curing geopolymer achieved by adding calcium to augment the curing rate. Metakaolin is used as the main raw material, and aqueous solutions of KOH and $K_2SiO_3$ are used as the activators. As a result of optimizing the high bending strength as a target factor for geopolymers with $SiO_2/Al_2O_3$ ratio of 4.1 ~ 4.8, the optimum ranges of the active agent are found to be $0.1{\leq}K_2O/SiO_2{\leq}0.4$ and $10{\leq}H_2O/K_2O{\leq}32.5$, and the optimum range of the curing accelerator is found to be $$0.82{\leq_-}Ca(OH)_2/Al_2O_3{\leq_-}2.87$$. The maximum flexural strength is found to be 1.35 MPa at $Ca(OH)_2/Al_2O_3=2.82$, $K_2O/SiO_2=0.3$, and $H_2O/K_2O=11.3$. The physical and thermal properties are analyzed to validate the applicability of these materials as industrial insulating parts or repairing finishing materials in construction.

• Composites Research
• /
• v.35 no.4
• /
• pp.288-297
• /
• 2022

This study investigated the effect of addition of zirconia(zirconium oxide) powder on the curing behavior of phenolic resins. The heating rate controlled curing and isothermal curing behaviors of the phenol resin according to the content of the zirconia powder were analyzed. The viscosity and thermal decomposition characteristics of the phenolic resin with the zirconia content were also examind. From the DSC analysis, the degree of cure and the rate of cure were obtained. Finally, the activation energy for the cure reaction were calculated from the DSC data of the zirconia added phenolic resin. As a found, the higher the zirconia content, the longer the curing was delayed and the greater the activation energy required for curing. Additionally, the TGA result that as the content of zirconia increased, less weight loss was observed. The surface tackiness of the Carbon/Phenol prepreg was partially changed according to the zirconia content, but had no significant effect.

• Composites Research
• /
• v.19 no.4
• /
• pp.31-38
• /
• 2006

In this study, effects of curing temperature and autofrettage pressure on a Type 3 cryogenic propellant tank, which is composed of composite hoop/helical layers and a metal liner, were investigated by thermo elastic analysis and composite/aluminum ring specimen tests. Temperature field of a Type 3 tank was obtained from solving the heat transfer problem and, in turn, was used as nodal temperature boundary conditions during the elastic analyses for curing temperature and autofrettage pressure effects. As a result, it was shown that the higher curing temperature was, the more residual compressive stress and tensile stress were induced in composites and metal liner, respectively. On the contrary, autofrettage pressure brought the reduction of these residual thermal stresses caused by cryogenic environments to the tank structure. This tradeoff for curing temperature and autofrettage pressure must be considered in the design and manufacturing stages for a Type 3 cryogenic tank.

• Carbon letters
• /
• v.12 no.1
• /
• pp.53-56
• /
• 2011

This study aimed to investigate the influence of mesoporous carbons on the thermal insulation properties of epoxy/mesoporous carbon composites. The mesoporous carbon (CMK-3) was prepared by conventional templating method using SBA-15. The epoxy/mesoporous carbon composites were prepared by mixing the synthesized CMK-3 with diglycidylether of bisphenol A (DGEBA). As experimental results, the curing reactivities of the DGEBA/CMK-3 composites were found to decrease with the addition of the CMK-3. Also, the thermal conductivities of DGEBA/CMK-3 composites were found to decrease with increasing CMK-3 content. This could be interpreted in terms of the slow thermal diffusion rate resulting in pore volume existing in the gaps in the interfaces between the mesoporous carbon and the DGEBA matrix.

• Composites Research
• /
• v.33 no.1
• /
• pp.25-29
• /
• 2020

A liquid crystalline thermosetting-epoxy-based composite was fabricated using diglycidyl ether of 4,4'-biphenol, tin(IV) oxide as a filler, and sulfanilamide as a curing agent. To investigate the thermal behavior, Thermogravimetric Analysis and Laser Flash Apparatus were performed using 3.0-7.0 wt% Tin(IV) oxide. The result showed that the activation energy and thermal conductivity were proportional to the amount of added filler.

• Magazine of the Korea Concrete Institute
• /
• v.27 no.6
• /
• pp.63-67
• /
• 2015