• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.2 no.3
• /
• pp.1-9
• /
• 1999

This paper described the results of the characteristics of the near-bottom flow and field analysis of the tidal flats sediment. It was the aim of this paper to grasp current flow of tidal flat's environment and influence factor for environmental change forecast of tidal flats. Field measurement of water velocity, water elevation, bed materials test, and temperature distribution of tidal flat were conducted. Thereafter, current flow, turbidity and temperature distribution of tidal flat sediment have been discussed. The field research results showed that the fluctuating velocity near the seabed before and after its appearance at low tide was strongly affected by the wind wave. The resuspension of the sea-bottom sediment took place with great intensity before and after the appearance of the seabed at low tide. Both the sea water level and the weather condition were a significant influential factors. Such as, temperature and turbidity just on the surface and the shallow layer of seabed sediments were varied largely with time and weather conditions, but that its deeper layers was almost constant. Temperature on the seabed sediments was strongly influenced by irradiance and water depth. The temperature variation of the tidal flat and the variation characteristics of the current flow and turbidity depend greatly on the inhabiting environment of the tidal flat benthic organism.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.2
• /
• pp.165-173
• /
• 2004

Laser beam welding is increasingly being used in welding of structural steels. The laser welding process is one of the most advanced manufacturing technologies owing to its high speed and deep penetration. The thermal cycles associated with laser welding are generally much faster than those involved in conventional arc welding processes, leading to a rather small weld zone. Experiments are performed for 304 stainless steel plates changing several process parameters such as laser power, welding speed, shielding gas flow rate, presence of surface pollution, with fixed or variable gap and misalignment between the similar and dissimilar plates, etc. The following conclusions can be drawn that laser power and welding speed have a pronounced effect on size and shape of the fusion zone. Increase in welding speed resulted in an increase in weld depth/ aspect ratio and hence a decrease in the fusion zone size. The penetration depth increased with the increase in laser power.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.342-349
• /
• 2011

The purpose of this paper is to describe experimental results about the butt welding and bead on plate welding of the high power Continuous Wave (CW) Fiber laser for Ultra-low carbon Interstitial Free(IF) steel plate for gear part of car. After being welded of the gear parts by the fiber laser and electron beam Microstructures of melting zone had been mixed acicular, granular bainitic, quasi-polygonal and widmanstatten ferrite because of a radical thermal diffusion after welding, difference of critical volume and grain size. As a result of experiment, when gear parts were welded by the fiber laser and electron beam, the fiber laser welding has been stable properties without internal defects more than the electron beam welding. Therefore it has the very advantages of welding high quality and productivity more than conventional melting method. The optimal welding processing parameters for gear parts were as follows : the laser power and welding speed were 3kWatt, 30mm/sec respectively. At this time heat input was $21.2{\times}10^3J/cm^2$.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.9
• /
• pp.417-422
• /
• 2002

ZnO thin films were deposited on various substrates, such as Si-(111), SiO$_2$(5000 $\AA$ by thermal CVD)/Si-(100), and SiO$_2$(2000 $\AA$ by RF sputtering)/Si-(100). The (002)-orientation, surface morphology and roughness, and electrical resistivity of deposited films were measured and compared in terms of substrate. Surface acoustic wave(SAW) filters with a multilayered configuration of IDT/ZnO/SiO$_2$/Si were also fabricated and the IDT was obtained using a lift-off method. From the frequency-response characteristics of fabricated devices, the insertion loss and side-lobe rejection were estimated. The experimental results showed that the (002)-oriented growth nature of ZnO films, which played a crucial role of determining the characteristic of SAW device, was strong1y dependent upon the SiO$_2$buffer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.53-57
• /
• 2006

In this paper, maxwell 3D finite element analysis program (Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250 kHz and some specific conditions. The electromagnetic field in the ferrite core was shown to be high and symmetric. An LS-100 luminance meter and a Darsa-2000 spectrum analyzer were used in the experiment. According to data on the lamp tested using high magnetic field ferrite, the optical and thermal wave fields were shown to be high around the ring-shaped electrodeless fluorescent lamp. The optical or light field was high at the center of the bulb rather than around the ferrite core. The light conditions of the bulb were assumed to be complex, depending on the condition of the filler gas, the volume of the bulb, and the frequency of the inverter. Our results have shown coupling between the gas plasma and the field of the light emitted to be nonlinear.

• Journal of the Korean Society of Combustion
• /
• v.21 no.2
• /
• pp.22-28
• /
• 2016

High efficient and environment friendly combustion technologies are used to be operated an extreme condition, which results in unintended flame instability such as extinction and oscillation. The use of electromagnetic energy is one of methods to enhance the combustion stability and a microwave as electromagnetic wave is receiving increased attention recently because of its high performance and low-cost system. In this study, an experiment was performed with jet diffusion flames induced by microwave. Micro jet was introduced to simulate the high velocity of industrial combustor. The results show that micro jet flames had three different modes with increasing oxidizer velocity; attached yellow flame, lifted flame, and lifted partially premixed flame. As a microwave was induced to flames, the overall flame stability and blowout limit were extended with the higher microwave power. Especially the interaction between a flame and a microwave was shown clearly in the partially premixed flame, in which the lift-off height decreased and NOx emission measured in post flame region increased with increasing microwave power. It might be attributed to increase of reactivity due to the abundance of radical pool and the enhanced absorption to thermal energy.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.125-131
• /
• 2005

This article reports the experimental and numerical results for free sprays under ultra-high injection pressure conditions to give us better understandings of spray characteristics and also to make clear a limit pressure condition in diesel sprays. The high pressure injection system developed in this work is devised to reach ultra-high pressure conditions in the range from 150 MPa to 355 MPa. The free spray injected from a single nozzle injector is visualized by the Schlieren technique and the high speed camera. In particular, it is found that the shock waves are present and propagated along the edge of spray in the downstream direction. The measured spray penetration length increases gradually with the injection pressure, but its increasing rate is decreased as the injection pressure increases. The Sauter mean diameter is also no longer augmented for the injection pressures higher than 300 MPa. In addition, the three­dimensional numerical simulations are conducted for comparing the measurements with the predictions based on two different breakup models. The TAB model results show better agreements with experimental data than the WAVE model under ultra-high injection pressure conductions. Moreover, the simulation results show that the gas-phase pressure increases substantially in the vicinity of the spray tip region. It supports the experimental observation that the shock waves are formed at the front of spray tip and are propagated downstream.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.76-79
• /
• 2005

$Nd:YVO_4$ 연속발진 레이저(CW laser:Continuous wave laser)로 제작한 다결정 실리콘 박막의 이온도핑 효과를 조사하였다. PECVD로 증착한 비정질 실리콘 박막을 CW 레이저를 조사하여 결정화한 후 $B_2H_6$ 플라즈마 이온 도즈량을 변화시켜 이온 도핑을 하고 급속열처리 방법과 퍼니스 어닐링 방법으로 도펀트 활성화를 하였다. 이온 도핑된 CW 다결정 실리콘 박막의 이온 도즈량에 따른 판저항 변화를 비교하고, 급속열처리(RTA: Rapid Thermal Annealing)와 퍼니스 어닐링(FA: Furnace Annealing) 전후의 결정성 변화를 라만 스펙트럼(Raman spectrum) 을 통하여 분석하였다. 이온 도즈량이 증가함에 따라 판저항은 감소하고, 어닐링 후 이온 도핑에 의해 손상된 박막이 복원됨을 확인 할 수 있다.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.5
• /
• pp.424-428
• /
• 1996

TlCl2(TCNQ)2.5 and Tl(TCNQ)3 were obtained from the reaction of LiTCNQ (TCNQ=tetracyanoquinodimethane) and TlX3 (X=Cl and NO3). These compounds were characterized by spectroscopic(IR, UV, EPR), electrochemical methods, and electrical conductivity measurements. Thermal analysis (TG, DSC) was also conducted. The room temperature electrical conductivities of these compounds are in the range of semiconductors. Spectroscopic studies indicate that Tl(TCNQ)3 has fully ionized TCNQ- ions in a form of simple salt, whereas TlCl2(TCNQ)2.5 is consisted of TCNQ- and TCNQ0 as a complex salt. EPR values of TCNQ- radical anion are 1.999 in both compounds and the signal attributable to metal ion is not observed, suggesting that any unpaired electrons are localized on TCNQ radicals, and metal atoms have diamagnetic state. Ligand decomposition and reduction process are simultaneously progressed in both compounds above at 200 ℃. The endothermic activation energy of TlCl2(TCNQ)2.5 is shown somewhat larger than that of Tl(TCNQ)3, it may be due to Tl-Cl bond strength. The mid-peak potentials of these compounds are very similar to those of TCNQ and the values of Epa and Epc are almost equal to 1. The wave of thallium ion is not detected in cyclic voltammogram, hence the redox processes of the complexes might be mainly localized to the TCNQ ligand rather than thallium ion.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.457-462
• /
• 2011

This paper presents a numerical investigation of deflagration to detonation transition (DDT) induced by shock wave and flame interaction in ethylene-air mixtures. Also shows the change of DDT triggering time by wall cooling effect. A model is consisted of the compressible reactive Navier-Stokes equations. And the effect of viscosity, thermal conduction, molecular diffusion, chemical reaction and wall effect are included. Using this model, the generation of hot spot by repeated shock and flame interaction, occurrence of detonation, and wall cooling effect of detonation confining boundaries are studied.