• Nuclear Engineering and Technology
• /
• 제45권2호
• /
• pp.191-202
• /
• 2013

A numerical analysis of thermal stratification in the upper plenum of the MONJU fast breeder reactor was performed. Calculations were performed for a 1/6 simplified model of the MONJU reactor using the commercial code, CFX-13. To better resolve the geometrically complex upper core structure of the MONJU reactor, the porous media approach was adopted for the simulation. First, a steady state solution was obtained and the transient solutions were then obtained for the turbine trip test conducted in December 1995. The time dependent inlet conditions for the mass flow rate and temperature were provided by JAEA. Good agreement with the experimental data was observed for steady state solution. The numerical solution of the transient analysis shows the formation of thermal stratification within the upper plenum of the reactor vessel during the turbine trip test. The temporal variations of temperature were predicted accurately by the present method in the initial rapid coastdown period (~300 seconds). However, transient numerical solutions show a faster thermal mixing than that observed in the experiment after the initial coastdown period. A nearly homogenization of the temperature field in the upper plenum is predicted after about 900 seconds, which is a much shorter-term thermal stratification than the experimental data indicates. This discrepancy may be due to the shortcoming of the turbulence models available in the CFX-13 code for a natural convection flow with thermal stratification.

• 설비공학논문집
• /
• 제18권6호
• /
• pp.493-500
• /
• 2006

This paper concerns the measurement of thermal conductivity of grouting materials for ground loop heat exchanger. A thermal conductivity meter, QTM-500 based on modified transient hot wire method was used to measure the thermal conductivity of neat bentonite and mixtures of bentonite and various additives. Relative to the total mixture mass, as the percent additive was increased the mixture thermal conductivity increased. For the bentonite-silica sand mixtures, the higher density of the sand particles resulted in much higher mixture thermal conductivity. The quartzite and silica sands produced the largest increases in mixture thermal conductivity, while common masonry and limestone sands produced lower thermal conductivity increases.

• 전산구조공학
• /
• 제9권2호
• /
• pp.153-161
• /
• 1996

본 논문에서는 가압열충격의 파괴역학적 해석에 필요한 이론을 조사하였고 원자로용기의 구조건전성을 평가하기 위하여 해석과정을 전산화하였다. 우선 사고 transient에 대하여 원자로용기내의 압력과 주입되는 냉각재의 온도변화가 주어지면 이들로 부터 시간에 따른 용기에서의 온도와 응력분포를 구하고, 중성자 조사량과 용기 재질의 화학성분으로 부터 기준무연성천이온도의 분포가 구해지며 이로부터 파괴인성치 K/sub IA/와 K/sub IC/의 분포가 얻어진다. 또한 응력분포로 부터 균열의 크기 및 형상에 따라 응력확대계수 K/sub I/이 구해지므로 이를 K/sub IA/및 K/sub IC/와 비교함으로써 균열의 성장거동을 예측할 수 있다. 지금까지 보고된 가압열충격을 유발할 수 있는 대표적인 사고 transient가 국내 발전소에 발생할 경우를 가정하여 해석을 수행하였고 그 결과에 대하여 검토하였다.

• International Journal of Aeronautical and Space Sciences
• /
• 제1권2호
• /
• pp.22-29
• /
• 2000

A method to simulate the gas turbine transient behavior is developed. The basic principles of the method and main input data required are described. Calculation results are presented in terms of whole operating regime of the engine. The influence of initial parameters such as starting engine power, moment of inertia of the rotor, fuel schedule on performance characteristics of gas turbine during transient operation is shown. In addition, the effect of bleeding air on transient behavior is also considered. For validation of the developed computer code, a comparative analysis with experimental data obtained from a heavy duty gas turbine is made. Calculation results agree well with the experimental data for the range of operating regime studied and proved applicability of the developed technique to initial design stage of control system.

• Structural Engineering and Mechanics
• /
• 제53권4호
• /
• pp.645-659
• /
• 2015

This research investigates the thermoelastic transient behavior of a thermally loaded slab made of a thermal diode-like material which has two directional thermal conductivity values (low and high). Finite difference analysis is used to obtain the elastic response of the slab based on the temperature solutions. It is found that the rate of heat transfer through the thickness of the slab decreases with reducing the ratio between the low and high thermal conductivity values (R). In addition, reducing R makes the slab less responsive to the thermal load when heated from the direction associated with the low thermal conductivity value.

• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.949-956
• /
• 2009

The C(t)-integral describes amplitude of stress and strain rate field near a tip of stationary crack under transient creep condition. Thus the C(t)-integral is a key parameter for the high-temperature crack assessment. Estimation formulae for C(t)-integral of the cracked component operating under mechanical load alone have been provided for decades. However, high temperature structures usually work under combined mechanical and thermal load. And no investigation has provided quantitative estimates for the C(t)-integral under combined mechanical and thermal load. In this study, 3-dimensional finite element analyses were conducted to calculate the C(t)-integral of elastic-creep material under combined mechanical and thermal load. As a result, redistribution time for the crack under combined mechanical and thermal load is re-defined through FE analyses to quantify the C(t)-integral. Estimates of C(t)-integral using this proposed redistribution time agree well with FE analyses results.

• 조명전기설비학회논문지
• /
• 제25권12호
• /
• pp.34-41
• /
• 2011

In order to understand the thermal performance of each LED chips in multi-chip LED package, a quantitative parametric analysis of the temperature evolution was investigated by thermal transient analysis. TSP (Temperature Sensitive Parameter) value was measured and the junction temperature was predicted. Thermal resistance between the p-n junction and the ambient was obtained from the structure function with the junction temperature evolution during the cooling period of LED. The results showed that, the thermal resistance of the each LED chips in 4 chip-LED package was higher than that of single chip- LED package.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.713-718
• /
• 2006

This paper concerns the measurement of thermal conductivity of grouting materials for ground loop heat exchanger. A thermal conductivity meter, QTM-500 based on modified transient hot wire method was used to measure the thermal conductivity of neat bentonite and mixtures of bentonite and various additives. Relative to the total mixture mass, as the percent additive was increased the mixture thermal conductivity increased. For the bentonite-silica sand mixtures, the higher density of the sand particles resulted in much higher mixture thermal conductivity.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2001년도 전지기술심포지움
• /
• pp.145-161
• /
• 2001

Novel characterization of thermal properties of a battery has been introduced by defining its frequency-dependent thermal impedance function. Thermal impedance function can be approximated as a thermal impedance spectrum by analyzing experimental temperature transient which is related to the thermal impedance function through Laplace transformation. In order to obtain temperature transient, a process has been devised to generate external heat pulse with heating wire and to measure the response of battery. This process is used to study several commercial Li-ion batteries of cylindrical type. The thermal impedance measurements have been performed using potentionstat/galvanostate controlled digital signal processor, which is more commonly available than flow-meter usually applied for thermal property measurements. Thermal impedance spectra obtained for batteries produced by different manufactures are found to differ considerably. Comparison of spectra at different states of charge indicates independence of thermal impedance on charging state of battery. It is shown that thermal impedance spectrum can be used to obtain simultaneously thermal capacity and thermal conductivity of battery by non-linear complex least-square fit of the spectrum to thermal impedance model. Obtained data is used to simulate a response of the battery to internal heating during discharge. It is found that temperature inside the battery is by one-third larger that on its surface. This observation has to be considered to prevent damage by overheating.

• 대한기계학회논문집A
• /
• 제34권2호
• /
• pp.129-138
• /
• 2010

공업용 세라믹은 자체의 특이한 물리적 특성으로 인하여 극한의 열 및 화학적 환경에서도 적용할 수 있는 우수한 고온 재료이다. 세라믹은 고온에서 저온으로 빠르게 이동되면 열충격을 받는다. 본 연구에서는 열충격에 대한 매개변수로 임계온도차이를 제안한다. 세라믹 부품에 대한 임계온도차이는 부품 크기와 대류열전달계수 등에 의해 영향을 받는다. 부품의 열충격 특성은 비정상 열응력에 의해 평가된다. 비정상 열응력이 파단계수를 초과한다면 열충격 균열이 표면에서 시작된다고 가정할 수 있다. 물에 대한 임계온도차이는 공기에 대한 임계온도차이보다 적다. 본 연구에서 사용된 국내 승용차용 삼원 촉매 담체는 반경 및 축방향 온도차이가 임계온도차이 아래에 존재하므로 충분한 열충격 성능을 가지고 있었다.