• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.108-115
• /
• 2010

The effects of acid-treated MWCNT and coupling agent on properties of MWCNT/SBR are investigated in this work. The MWCNTs oxidized using sulfuric and nitric acids were analyzed by the Raman scattering and Fourier transformed infrared spectroscopy(FT-IR). The FT-IR results indicate the presence of -COOH groups in the treated samples, and Raman spectroscopy of the acidtreated MWCNTs further corroborates the formation of surface defect due to the introduction of carboxyl groups. And the nanocomposites reinforced with MWCNTs were characterized extensively using the scanning electron microscopy(SEM), electrical conductivity, thermal conductivity, and tensile properties measurements. The results showed that nanocomposites onto acid-treated MWCNTs enhanced mechanical properties compared to those containing MWCNTs without acid treatment. These findings confirmed the improved interfacial interactions between MWCNTs and SBR arising from the coupling agents. But the electrical and thermal conductivity of nanocomposites decreased due to the chopping and formation of surface defects of MWCNTs.

• Polymer(Korea)
• /
• v.38 no.6
• /
• pp.787-790
• /
• 2014

In this work, the epoxy specimens were prepared from diglycidyl ether of bisphenol F (DGEBF) with silane coupling agents (3-glycidoxypropyl trimethoxysilane (GPTMS)) in different ratios. Thermal stability was studied in terms of polymer decomposition temperature (PDT), temperature of maximum rate of weight loss ($T_{max}$), integral procedural decomposition temperature (IPDT), and decomposition activation energy ($E_a$) using TGA analysis. Adhesion properties of epoxy composite specimens were measured by UTM (universal testing machine) at atmosphere temperature. In this result, the adhesion properties of DGEBF were improved by addition of silane coupling agents compared to non-treated epoxy resin. However, when the content of GPTMS agent is more than 10 phr, adhesion properties decreased with increasing GPTMS agent.

• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.1974-1987
• /
• 2023

The load-following operation of small modular reactors (SMRs) requires accurate prediction of transient behaviors that can occur in the balance of plants (BOP) and the nuclear steam supply system (NSSS). However, 1-D thermal-hydraulics analysis codes developed for safety and performance analysis have conventionally excluded the BOP from the simulation by assuming ideal boundary conditions for the main steam and feed water (MS/FW) systems, i.e., an open loop. In this study, we introduced a lumped model of BOP fluid system and coupled it with NSSS without any ideal boundary conditions, i.e., in a closed loop. Various methods for coupling boundary conditions at MS/FW were tested to validate their combination in terms of minimizing numerical instability, which mainly arises from the coupled boundaries. The method exhibiting the best performance was selected and applied to a transient simulation of an integrated NSSS and BOP system of a SMART. For a transient event with core power change of 100-20-100%, the simulation exhibited numerical stability throughout the system without any significant perturbation of thermal-hydraulic parameters. Thus, the introduced boundary-condition coupling method and BOP fluid system model can expectedly be employed for the transient simulation and performance analysis of SMRs requiring daily load-following operations.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.91-98
• /
• 2010

The increasing of power and processing speed and miniaturization of central processor unit (CPU) used in electronics equipment requires better performing thermal management systems. A typical thermal management package consists of thermal interfaces, heat dissipaters, and external cooling systems. There have been a number of experimental techniques and procedures for estimating thermal conductivity of thin, compressible thermal interface material (TIM). The TIM performance is affected by many factors and thus TIM should be evaluated under specified application conditions. In compact packaging of electronic equipment the chip is interfaced with a thin heat spreader. As the package is made thinner, the coupling between heat flow through TIM and that in the heat spreader becomes stronger. Thus, a TIM characterization system for considering the heat spreader effect is proposed and demonstrated in detail in this paper. The TIM test apparatus developed based on ASTM D-5470 standard for thermal interface resistance measurement of high performance TIM, including the precise measurement of changes in in-situ materials thickness. Thermal impedances are measured and compared for different directions of heat dissipation. The measurement of the TIM under the practical conditions can thus be used as the thermal criteria for the TIM selection.

• Journal of Magnetics
• /
• v.5 no.2
• /
• pp.50-54
• /
• 2000

NiMn-pinned spin valve films consisting of a layered glass/NiFe/Co/Cu/Co/NiFe/NiMn/Ta stack were made by do magnetron sputtering. After deposition, the structure was annealed in a series of cycles each including three hours at $220^\circ C, 2\times10^{-6}$ Torr, in a field of 350 Oe, to create an ordered antiferromagnetic structure in the NiMn layer and produce a strong unidirectional pinning field in the pinned magnetic layer, Optimum spin valve properties were obtained after seven annealing cycles, or 21 hours at $220^\circ C$, and were : MR ratio 1%, exchange coupling field 620 Oe, and coercivity of pinned layer 250 Oe. The exchange coupling field remained constant up to an operating temperature of $175^\circ C$, and the blocking temperature was about $380^\circ C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.176.1-176.1
• /
• 2014

Graphene has attracted an increasing attention due to its extraordinary electronic, mechanical, and thermal properties. Especially, the two dimensional (2D) sheet of graphene with an extremely high surface to volume ratio has a great potential in the preparation of multifunctional nanomaterials, as 2D supports to host metal nanoparticles (NPs). Copper oxide is widely used in various areas as antifouling paint, p-type semiconductor, dry cell batteries, and catalysts. Although the copper oxide(II) has been well known for efficient catalyst in C-N cross-coupling reaction, copper oxide(I) has not been highlighted. In this research, CuO and Cu2O nanoparticles (NPs) dispersed on the surface of grapehene oxide (GO) have been synthesized by impregnation method and their morphological and electronic structures have been systemically investigated using TEM, XRD, and XAFS. We demonstrate that both CuO and Cu2O on graphene presents efficient catalytic performance toward C-N cross coupling reaction. The detailed structural difference between CuO and Cu2O NPs and their effect on catalytic performance are discussed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.2
• /
• pp.213-218
• /
• 2013

In this study, epoxy/mica composite was prepared by mixing with mechanical stirrer together with homogenizer, and the effect of amino-type silane coupling agent was also studied. To reduce the viscosity without any decrement of other properties, 1,4-Butanediol diglycidyl ether (1,4-BDGE) as an aliphatic epoxy reactive diluent was introduced to the epoxy/mica composite in order to use as vanish for high voltage motor and generator stator winding. It was confirmed by scanning electron microscopy (SEM) observation that interfacial characteristics between organic epoxy and inorganic mica was modified by coupling agent treatment so that glass transition temperature increased, and tensile strength and electrical breakdown strength increased. The properties were estimated by Weibull statistical analysis and the ac electrical breakdown strength was 20.2% modified by treating silane coupling agent.

• Nuclear Engineering and Technology
• /
• v.49 no.6
• /
• pp.1339-1345
• /
• 2017

In the framework of the EU funded project NURESAFE, the subchannel code CTF and the neutronics code DYN3D were integrated and coupled on the NURESIM platform. The developments achieved during this 3-year project include assembly-level and pin-by-pin multiphysics thermal hydraulics/neutron kinetics coupling. In order to test this coupling, a PWR rod ejection transient was simulated on a MOX/UOX minicore. The transient is simulated using two different models of the minicore. In the first simulation, both codes model the core with an assembly-wise resolution. In the second simulation, a pin-by-pin fuel-centered model is used in CTF for the central assembly, and a pin power reconstruction method is applied in DYN3D. The analysis shows the influence of the different models on global parameters, such as the power and the average fuel temperature, but also on local parameters such as the maximum fuel temperature.

• Elastomers and Composites
• /
• v.55 no.4
• /
• pp.339-346
• /
• 2020

We functionalized a wear-resistant carbon-based MoS2 filler to solve its limited wear condition problem. The filler exhibits excellent lubricative properties. The surface modification of MoS2 was carried out using a (3-glycidyloxypropyl)trimethoxysilane (GPTMS) silane coupling agent to improve the low compatibility and dispersibility of the filler that generally degrade the performance of composites. A silane coupling agent was employed for the functionalization of MoS2, and its effect on the wear resistance of MoS2/Polyamide-6,6 was investigated. The silanization of MoS2 was identified by contact angle analysis and Fourier-transform infrared, energy dispersive X-ray, and X-ray photoelectron spectroscopies. The wear resistance of the composite was found to be improved significantly by the surface functionalization of MoS2.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.229-229
• /
• 2003

Enhancement of the exchange bias and optimization of the structure have been the focus that many researchers studied, recently [1]. In this report, magnetic properties of MTJs with structure of Si/Ta (5)/Cu (10)/ Ta (5)/ Ni$\sub$80/Fe$\sub$20/ Cu (5)/ Mn$\sub$75Ir$\sub$25/ (10)/ Co$\sub$70/Fe$\sub$30/ (2.5)/ Al-O (1.5)/ Co$\sub$70/Fe$\sub$30/ (2.5)/ Ni$\sub$80/Fe$\sub$20/ (t)/ Ta (5) (t=0,10, 30, 60 and 100 nm, respectively) were investigated. The relationship between the structure and magnetic parameters of interfacial exchange coupling and interlayer coupling in as-deposited and annealed junctions was studied. The temperature dependence of exchange coupling was considered.