• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.3
• /
• pp.63-69
• /
• 1983

A theoretical equation is presented to estimate the lateral earth pressures acting on piles in a row in cohesionless soil. Then, a series of model tests are carried out for various kinds of pile diameters and pile intervals, followed by very good agreements between the experimental and theoretical values of the lateral earth pressures on piles. The experimental results prove the validity of an assumption on the plastic condition of soil around piles set up in the theoretical derivation. And also the significance of the theoretical values by the presented theoretical equation is clarified.

• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.199-205
• /
• 2014

The current study examines the effect of the analytical parameter values on the theoretical forming limit diagram (FLD) based on the Marciniak-Kuczynski model (M-K model). Tensile tests were performed to obtain stress-strain curves and determine the anisotropic properties in the rolling, transverse and diagonal direction of SPCC sheet materials. The experimental forming limit curve for SPCC sheet material was obtained by limiting dome stretching tests. To predict the theoretical FLD based on the M-K model, the Hosford 79 yield function was employed. The effects of three analytical parameters - the exponent of the yield function, the initial imperfection parameter and the fracture criterion parameter - on the M-K model, were examined and the results of the theoretical FLD were compared to the experimentally measured FLD. It was found that the various analytical parameters should be carefully considered to reasonably predict the theoretical FLD. The comparison of the acceptable forming limit area between the theoretical and experimental FLD is used to compare the two diagrams.

• Steel and Composite Structures
• /
• v.26 no.5
• /
• pp.595-606
• /
• 2018

A calculation method was presented to calculate the deflection of GFRP-concrete-steel beams with full or partial shear connections. First, the sectional analysis method was improved by considering concrete nonlinearity and shear connection stiffness variation along the beam direction. Then the equivalent slip strain was used to take into consideration of variable cross-sections. Experiments and nonlinear finite element analysis were performed to validate the calculation method. The experimental results showed the deflection of composite beams could be accurately predicted by using the theoretical model or the finite element simulation. Furthermore, more finite element models were established to verify the accuracy of the theoretical model, which included different GFRP plates and different numbers of shear connectors. The theoretical results agreed well with the numerical results. In addition, parametric studies using theoretical method were also performed to find out the effect of parameters on the deflection. Based on the parametric studies, a simplified calculation formula of GFRP-concrete-steel composite beam was exhibited. In general, the calculation method could provide a more accurate theoretical result without complex finite element simulation, and serve for the further study of continuous GFRP-concrete-steel composite beams.

• Journal of the Korean Society of Visualization
• /
• v.10 no.1
• /
• pp.27-33
• /
• 2012

This paper describes a new design of small-scale horizontal wind blade, called spiral wind turbine blade. Theoretical and numerical approaches on the prediction of aerodynamic performance of the blade have been conducted. A theoretical equation is successfully derived using the angular momentum equation to predict aerodynamic characteristics according to the design shape parameters of spiral blade. To be compared with the theoretical value, a numerical simulation using ANSYS CFX v12.1 is performed on the same design with the theoretical one. Large scale tip vortex is captured and graphically presented in this paper. The TSR-$C_p$ diagram shows a typical parabolic relation in which the maximum efficiency of the blade approximately 25% exists at TSR=2.5. The numerical simulation agrees well with that of the theoretical result except at the low rotational speed region of 0~20 rad/s.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.2
• /
• pp.70-77
• /
• 2003

Theoretical estimation of overall stoichiometry for the microbial degradation of hazardous organic compounds is described. Half-reaction method based on microbial energetics was used in the theoretical estimation. In addition to the half-reaction method, other theoretical methods such as intermediate formation, oxygenation reaction, and estimation of the standard free energy of formation by group contribution theory were also applied. As a case study, the application of these methods was demonstrated for the estimation of microbial kinetics in the biodegradation of phenanthrene which was chosen as a model hazardous organic compound along with glucose and hexadecane. The cell yield, oxygen requirement, nitrogen requirement, and mineralization ratio could be estimated from the overall stoichiometry. It is believed that these theoretical estimation methods are useful tools for practical design and assessment of bioremediation of soil and groundwater contaminated with hazardous organic compounds.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.2
• /
• pp.208-213
• /
• 2012

In this study, the mechanical joint performance of the V-Insert clamp applied to automobile exhaust pipes was evaluated through the experimental investigation of its axial load capacity. The axial load of the V-Insert clamp was also determined by using theoretical equations presented by Shoghi and compared with the experimental results. As results of the theoretical prediction, the axial load of the V-Insert clamp tended to increase along with smaller angle of the V-Insert segment and the lower friction coefficient between the V-Insert segment and exhaust pipes. The experimental results under tightening effects were similar to the theoretical results and the axial load of the V-Insert clamp presented maximum values in the range of all torques at distance of 2mm between each exhaust pipes. The experimental results under loading effects were similar to the theoretical results in the range of lower torques but deviated from the theoretical results in the range of higher torques. These results would be beneficial to improve the joint and sealing performance of the V-Insert clamp.

• Steel and Composite Structures
• /
• v.17 no.2
• /
• pp.173-184
• /
• 2014

This study aimed to theoretical calculate the thermal residual stress in continuous SiC fiber reinforced titanium matrix composites. The analytical solution of residual stress field distribution was obtained by using coaxial cylinder model, and the numerical solution was obtained by using finite element model (FEM). Both of the above models were compared and the thermal residual stress was analyzed in the axial, hoop, radial direction. The results indicated that both the two models were feasible to theoretical calculate the thermal residual stress in continuous SiC fiber reinforced titanium matrix composites, because the deviations between the theoretical calculation results and the test results were less than 8%. In the titanium matrix composites, along with the increment of the SiC fiber volume fraction, the longitudinal property was improved, while the equivalent residual stress was not significantly changed, keeping the intensity around 600 MPa. There was a pronounced reduction of the radial residual stress in the titanium matrix composites when there was carbon coating on the surface of the SiC fiber, because carbon coating could effectively reduce the coefficient of thermal expansion mismatch between the fiber and the titanium matrix, meanwhile, the consumption of carbon coating could protect SiC fibers effectively, so as to ensure the high-performance of the composites. The support of design and optimization of composites was provided though theoretical calculation and analysis of residual stress.

• Structural Engineering and Mechanics
• /
• v.41 no.6
• /
• pp.805-822
• /
• 2012

Offshore pipelines have to withstand combined actions of tension and bending during deepwater installation, which can possibly lead to elliptical buckle and even catastrophic failure of whole pipeline. A 2D theoretical model initially proposed by Kyriakides and his co-workers which carried out buckling response analysis of elastic-plastic tubes under various load combinations, is further applied to investigate buckling behavior of offshore pipelines under combined tension and bending. In association with practical pipe-laying circumstances, two different types of loadings, i.e., bent over a rigid surface in the presence of tension, and bent freely in the presence of tension, are taken into account in present study. In order to verify the accuracy of the theoretical model, numerical simulations are implemented using a 3D finite element model within the framework of ABAQUS. Excellent agreement between the results validates the effectiveness of this theoretical method. Then, this theoretical model is used to study the effects of some important factors such as load type, loading path, geometric parameters and material properties etc. on buckling behavior of the pipes. Based upon parametric studies, a few significant conclusions are drawn, which offer a theoretical reference for design and installation monitoring of deepwater pipelines.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.1 s.145
• /
• pp.1-14
• /
• 2006

To improve maritime safety, it is very important not only to make safer design and operation but also to do proper response in case of maritime casualty. The large-scaled casualties will be caused by loss of structural strength and stability due to the progressive flooding and enlargement of damage by the effect of waves and wind. To prevent foundering and structural failure, the prediction of ship motion behavior of damaged ship in wave is necessary. This paper describes the motion behavior of damaged ship in waves through theoretical and experimental studies. A time domain theoretical model of damaged ship motions and accidental flooding, which can be applied to any type of ship or arrangement and considers the effects of flooding of compartments, has been developed. The model tests have been carried out in regular and irregular waves with different wave heights and directions in ship motion basin. Those were performed for three different damaged conditions such as engine room bottom damage, side shell damage and bow visor damage of a Ro-Ro ship. Comparison of theoretical and experimental results was performed.

• East Asian Journal of Business Economics (EAJBE)
• /
• v.10 no.4
• /
• pp.39-45
• /
• 2022

Purpose - This short paper reviews the debate dealing with the relationship between strategy and traditional strategy approach on the one hand, and business models and new business model approach on the other hand and tries to offer useful direction to be more helpful to theoretical discussions. Research design, data, and methodology - This paper makes a theoretical analysis to explain the confusion surrounding the debate, reviewing mainly literature survey papers and finds theoretical conjecture and its limitations in order to present useful direction to the future theoretical work. Result - In order to comprise its diversity, business model studies should consider the characteristics of each firm, sector, and market. Adding further elements which are related to each sector or market, theoretical studies can capture the diverse phenomena related to business model and business model innovation. Conclusion - The traditional strategy perspective can be utilized to the Business model phenomenon in the case of incumbent firms and non-digital sector and existing markets. Meanwhile the new business model perspective can be utilized to business model phenomena in case of start-ups and digital sector and emerging markets. Reconciling two perspectives, the studies dealing with the business model should focus on the characteristics of firms, markets, and knowledge from the perspective of business model innovation.