• Tribology and Lubricants
• /
• 제21권5호
• /
• pp.236-240
• /
• 2005

In order to prepare for the suitable surfaces of implants or medical devices, quantitative evaluation of adhesion between cells and biomaterials is essential. To better understand adhesion formation between cells and biomaterials, we used the cytodetachment technique which measures the adhesive force of a single cell through changing the, culture time and detachment speed. The results showed that the adhesive force could be affected by the culture time of cells on the surface of materials and the detachment speed. Moreover, there was a large discrepancy among the adhesion strength measured by similar techniques conducted on the different cells and substrates. It can be 'concluded that the variation of the force measurement technique can seriously alter the level of the force required to detach a cell on the surface of materials.

• 열처리공학회지
• /
• 제4권2호
• /
• pp.27-37
• /
• 1991

The adhesion strength of TiN films to substrate(STC 3) steel has been studied using the scratch adhesion test. Before deposition, the substrates were mechanically polished and TiN films were deposited at different substrate temperature($480^{\circ}C-540^{\circ}C$). The chemical properties of TiN films were investigated by RBS, and EDS, and the physical properties were investigated by micro-hardness tester, SEM, and X-ray diffractometer. According to results of this study, the adhesion strength of TiN films increase with increasing the deposition temperature. The roughness of the polished substrates surface were measured with a profilometer. It was observed that, as a general rule, the adhesion strength of deposited TiN films increase with decreasing the substrates surface roughness.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.319-322
• /
• 1999

The adhesion properties of polymer cement mortars for cement concrete repair were evaluated with respect to polymer-cement ratios and the surface conditions of cement concrete substrate. Styrene-butadiene rubber (SBR) was used as an additive for polymer cement mortars. The adhesion strength of cement mortar was smaller than that of polymer cement mortar. The adhesion strengths to the dry surfaces of substrate were larger than those to the wet surfaces, indicating that the dryness of substrate increased the adhesion strength in repairing concrete structures.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.15-19
• /
• 2002

In this work, the surface modification of carbon/epoxy composites was investigated using UV (ultraviolet ray) surface treatment to increase adhesion strength between the carbon/epoxy composites and adhesives. After UV surface treatment, XPS (X-ray photoelectron spectroscopy) tests were performed to analyze the surface characteristics of the carbon/epoxy composites. Comparing adhesion strengths with the surface characteristics, the effects of the surface modification of carbon/epoxy composites by UV surface treatments on the adhesion strengths were investigated.

• 한국재료학회지
• /
• 제9권12호
• /
• pp.1176-1180
• /
• 1999

Polyetherimide와 실리콘 사이의 RIE 처리 및 알루미늄 킬레이트 계열의 adhesion promoter 처리에 따른 접착력과 고온고습환경에서의 신뢰성 변화를 연구하였다. 실험 방법으로는 180$^{\circ}$ 필 테스트 및 <85$^{\circ}C$ 85%> 테스트, SEM, AFM, 증류수 접촉각 실험이 수행되었다. $^O_2$ RIE 실험 결과 초기 접착력은 RIE 처리시간에 따라 약간의 변화를 가져왔으나 고온고습 환경에서의 저항성은 급격히 떨어지는 것이 관찰되었고 이것은 표면 거칠기의 영향이 아닌 표면의 친수성 정도에 따른 것으로 나타났다. Al-chelate adhesion promoter의 경우 초기 접착력에는 변화가 없으나 고온 고습환경에서의 저항성이 크게 증가하였는데 이것은 표면이 소수성으로 변한 데 따른 것으로 나타났다.

• Journal of the Korean Wood Science and Technology
• /
• 제25권3호
• /
• pp.16-23
• /
• 1997

This study was carried out to discuss feasibility of high density polyethylene(HDPE) as a new substitute for the conventional adhesives in plywood manufacture. Plywood was composed of radiata pine(Pinus radiata) and Malas(Homallium feotidium) veneers and bonded by HDPE. Adhesion characteristics and anatomical scanning has been examined through tensile-shear strength test and scanning electron microscopy(SEM). The results are as follows; 1. Optimum loading quantity was 15g/$(30.3{\times}30.3)cm^2$, and tensile-shear strength increased with the increase of loading quantity. 2. Even at the hot pressing time of 1 minute, tensile-shear strength met the value of KS(over the 7.5kgf/$cm^2$), and tensile-shear strength increased with the increase of hot pressing time. 3. Plywood composed of veneer at moisture content of 19.6% showed similar tensile-shear strength to that at air conditioned moisture content of 11.4%. 4. Under the same condition of hot pressing time, tensile-shear strength of plywood bonded by HDPE met the KS value of boil and wet test and proved the same group as phenol formaldehyde adhesive. 5. HDPE films showed mechanical adhesion through penetration into the lathe check and ray of veneer.

• KSTLE International Journal
• /
• 제9권1_2호
• /
• pp.31-35
• /
• 2008

DLC (Diamond Like Carbon) films have predominant tribological properties like a high hardness, low friction and high chemical resistance; therefore, DLC films are applied in a wide range of industrial fields. This paper evaluated the characteristics of DLC films deposited on bearing steel with different hardness by RF-PECVD (Radio Frequency - Plasma Enhanced Chemical Vapor Deposition) method. Si-interlayer was deposited on bearing steel to improve adhesion strength by RF-Sputtering method. The DLC film structures were analyzed with Raman spectra and Gaussian function. Adhesion strength of DLC films was measured with a scratch tester. Friction and wear test were carried out with a ball-on -disc type to investigate the tribological characteristics. Experimental results showed that DLC films deposited on bearing steel under same deposition condition have typical structure DLC films regardless of hardness of bearing steel. Adhesion strength of DLC film is increased with a hardness of bearing steel. Friction coefficient of DLC film showed lower at the high hardness of bearing steel.

• 접착 및 계면
• /
• 제24권3호
• /
• pp.86-94
• /
• 2023

OLED 소자를 용액공정으로 제작함에 있어 음극 전극의 용액공정화가 기술적인 난제이므로 별도의 기판에 음극 전극을 형성하고 PEI 층을 접합층으로 사용하여 이를 다른 기판의 소자와 물리적, 전기적으로 연결하는 연구를 진행하였다. PEI 용액의 농도, PEI 층의 두께 및 첨가제 혼합 등을 변수로 하였으며 접착력 측정기와 EOD 소자 제작을 통하여 특성을 확인한 결과는 다음과 같다. PEI 용액의 농도가 높을수록 접착강도가 증가하였으나 막 두께의 증가로 전류 밀도가 감소하였다. 0.1 wt% PEI 용액에 첨가제로서 조비톨과 PEG를 혼합한 결과 PEG를 0.5 wt%의 농도로 혼합한 조건에서 900 mA/cm² 의 최대 전류 밀도를 얻었으며 양호한 접착 상태와 소자의 점등도 확인되었다.

• 한국표면공학회지
• /
• 제26권5호
• /
• pp.225-234
• /
• 1993

Titanium nitride coatings were deposited onto SUS304 stainless steel substrates pretreated by mechanical scrubbing, chemical etching at 50% HCl solution and Ar ion etching. Adhesion strength were measured by scratch tester and confirmed by SEM with EDS. Adhesion strength of Ar ion etched substrate was 10 to 15 times higher than that of mechanical scrubbed or chemical etched substrate. Ar ion etching brought about an uniform and fine spherical shaped surface, while chemical etching gave rise to a rough and irregular surface on SEM micrograph. It was suggested that higher adhesion strength might be caused by anchoring effect of Ar ion etched surface prior to TiN deposition.

• 한국재료학회지
• /
• 제11권11호
• /
• pp.923-928
• /
• 2001

An electrolytic silver plating process has been successfully developed for terminated electrode parts of dielectric ceramic resonator. High adhesion strength and high Qu is obtained and blister occurance is minimized under plating condition with $HNO_3$750 $m\ell/\ell$ and HF $ 250m\ell/\ell$ solution at $25^{\circ}C$ for 20 minutes. Adhesion strength has the highest value, 3.2 kg/mm$^2$ at etching temperature of $25^{\circ}C$. Adhesion strength, Qu and blister occurance are monotonically increased with the thickness of electrodeposition layer. In case of electrodeposition of Ag, Qu value of 380 has obtained higher than in case of electrolytic Cu plating with Qu value of 325. Therefore, terminated electrode parts of dielectric ceramic resonator reducing dielectric loss can be obtained using prensent process.