• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.77-84
• /
• 2012

The lithographic process depends on a satisfactory ink-in-water emulsion being formed during printing and the speed of wet presses makes the choice of fountain solution vitally important as the ink and fount must react quickly to form a stable emulsion. Ink and water come into contact with each other on the rolls of the press and are forced together in the roll nips. The water is not soluble in the ink since it is slightly fat. Instead, an emulsion is formed, a heterogeneous mass consisting of small water drops mixed into the ink, if the water feed is too great. This emulsification can affect the properties of an off-set ink and negatively affect the printability. So we investigated the effects of the emulsification of phenol free heat-set ink and existing heat-set ink on printed quality, such as amount of ink transfer, printed density, print-through and uniformity. We used Duke emulsification tester for the emulsification of inks, and used IGT printability tester for printed quality. The printed quality were measured by densitometer and were evaluated by the image analysis system. Compared to conventional printing ink, phenol-free ink showed better results of the printability at the emulsification.

• Environmental Mutagens and Carcinogens
• /
• v.8 no.1
• /
• pp.13-21
• /
• 1988

Mutagenic actions of aflatoxin B$_1$ (AFB$_1$) in the presence of various concentrations of L-ascorbIc acid (AA) in Salmonella typhimurium strains TA 100 and TA98 were studied. Spontaneous revertants per plate of the tester strains TA100 and TA98 were 121-125 and 25-30 with or without S9 mix, respectively. The negative controls used in the study did not show any mutagenesis in the tester strains. AFB$_1$ revealed strong mutagenicity at the dose levels of 0.05, 0.1 and 0.25 ${\mu}$g/plate with metabolic activation system in both strains. However, it showed a toxic effect when the levels were more than 0.5 ${\mu}$g/plate. When lower concentrations of AA (5-20 ${\mu}$g/plate) were added to AFB$_1$ in the Ames assay system with S9 mix the mutagenic action of AFB$_1$ decreased in both strains. About 70-90% of mutagenicity of AFB$_1$ disappeared in strain TA100 when 20${\mu}$g of AA was added to 0.05 ${\mu}$g of AFB$_1$. The inhibitory effect was greatly increased by the addition of higher concentrations of AA to AFB$_1$ in TA100 strain. The mutagenicity of AFB$_1$ was completely inhibited when 100 ${\mu}$g and 500 ${\mu}$g of AA were added to 0.05 ${\mu}$g and 0.1 ${\mu}$g of AFB$_1$, respectively, However, this protective effect of AA on AFB$_1$ mediated mutagenesis was less effective in TA98 strain than that in TA100.

• Journal of the Semiconductor & Display Technology
• /
• v.2 no.2
• /
• pp.31-37
• /
• 2003

This paper presents a measurement system of mechanical property using dual servo system. There are many kinds of method to measure material properties such as tensile test, indention and bending test. It is highly required to measure the properties of nano-sized material and structure. However, It is need more accurate measurement system, more stable and frequency response than conventional test. In this paper, we designed the dual servo system for a measuring instrument The dual servo system consisting of a coarse stage and a fine motion stage with VCM and PZT is proposed. Mechanical mechanism is designed with the leaf spring type of flexure hinge joint. Lead compensator is applied to this control system, and is designed by PQ method.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.349-350
• /
• 2002

The friction and wear behaviors of fluorine-containing compounds such as perfluoropolyethers (PFPE), phosphazenes (X-1P), ionic liquids as lubricants for steel/seel, steel/ceramic, ceramic/ceramic were investigated using a SRV tester and a one-way reciprocating friction tester both in ball-on-disc configuration. It was found that the three fluorine-containing lubricants could reduce friction coefficient and wear volume effectively. The effectiveness of the three lubricants in reducing wear volume could be ranked as ionic liquids>X-1P>PFPE. Tests also showed that aryloxyphosphazene with polar substituent as a lubricant of steel/steel pair gave low wear, while aryloxyphosphazene with nonpolar group on the phenyl pendant led to high wear. The morphology and the tribo-chemical reaction of the worn surfaces were analyzed with a scanning electron microscope (SEM) and X-ray photoelectron spectroscope (XPS). XPS analyses illustrated the formation of iron fluoride in steel/steel system with the lubrication of both phosphazenes and ionic liquids.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.36 no.2
• /
• pp.1-7
• /
• 2013

Cleanroom could be largely classified into industrial cleanroom that can be contaminated by particles and bio-cleanroom that can be contaminated by biological particles. Electrical manufacturing companies producing precision machines and electrical parts essentially have industrial cloom facilities and clean technologies to produce defects free products due to particles. Industrial cleanroom should be controlled in respect of 4M1E to prevent from foreign materials of sub-micro unit and to keep out contamination sources from outside. In this paper, a concept for a quantitative methodology to measure the particles from running components was suggested by combining both newly making clean booth such as wear tester and laser particle counter.

• Fire Science and Engineering
• /
• v.31 no.3
• /
• pp.19-24
• /
• 2017

Flammable substances are used in laboratories and industrial process. The flash point (FP) is one of the most important physical properties used to determine the potential for characterizing the fire and explosion hazard of liquids. The FP data at 101.3 kPa were measured for the binary systems {toluene+ethylbenzene}, {methlycyclohenxane+ethylbenzene} and {n-heptane+ ethylbenzene}. The experiments were performed according to the standard test method (ASTM D 3278) using a SETA closed cup flash point tester. The measured FPs were compared with the values predicted using the following activity coefficient models: Wilson, Non-Random Two Liquid (NRTL), and UNIversal QUAsiChemical (UNIQUAC). The average absolute deviation between the predicted and measured lower FP was less than 1.74 K.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.5
• /
• pp.97-103
• /
• 2002

The assessment of the condition of a transformer winding which is suspected of having suffered short circuit damage can be difficult. Conventional test such as winding resistance, magnetic current or insulation resistance will only detect damage if a permanent electrical fault exists. Visual inspection of windings necessitates the removal of oil and in many cases only a very small proportion of the winding can be seen. We describe the characteristic of LVI test system and methods to detect the deformation of windings in the power transformers. As the front rise time of recurrent-surge generator pulse less than 1000 ㎱ and the peak value of pulse is about 500 V, we have the good results of detecting winding deformation in the LVI test of transformers.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.467-470
• /
• 2004

Diamond-Like Carbon (DLC) thin film is a semiconductor with high mechanical hardness, low friction coefficient, high chemical inertness, and optical transparency. DLC thin films have widespread applications as protective coatings and solid lubricant coatings in areas such as Hard Disk Drive (HDD) and Micro-Electro-Mechanical-Systems (MEMS). In this work, the wear characteristics of DLC thin films deposited on silicon substrates using a DC-magnetron sputtering system were analyzed. The wear tracks were measured with an Atomic Force Microscope (AFM). To identify the sp2 and sp3 hybridization of carbon bonds and other bonds Raman spectroscopy was used. The structural information of DLC thin films was obtained with Fourier transform infrared spectroscopy and wear tests were conducted by using a micro-pin-on-reciprocator tester. Results showed that the wear characteristics were dependent on the sputtering conditions. The wear rate could be correlated with the bonding state of the DLC thin film.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.139-144
• /
• 2002

Ti-50.9at%Ni wires were welded using pulsed YAG laser. The laser welded wires were tested for investigating the shape memo교 effect and the ability of super elasticity. The fatigue properties of the welded wires were investigated using the rotary bending fatigue tester specially designed for wires. Moreover, the effect of defocusing distance during laser welding on the static and fatigue properties was investigated. The shape memory effect and super elasticity of the laser welded wires were approximately identical with that of base metal at the test temperature below 353K. However, the welded wires were broken within elastic limit at the test temperature above 353k. Under the cyclic bending loading conditions, the welded wires could be useful only below the elastic limit, while the base metal had sufficient fatigue life even the stress induced M-phase region. The fatigue strength of the welded wires was about half of that of the base metal. The deterioration of the static and fatigue properties in the welded wires was proven to be from the large difference of the transformation behavior between the base metal and welded part that is caused by vaporization of Ni-content at the welded part during the welding process. The defocusing distance below 3mm acted more largely on lowering the strength of the welded wires than that of 6mm or 8mm.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.443-446
• /
• 2009

In this study, a series of degradation test for structural adhesives was performed to investigate the possibility of replacement of the alternative adhesives to the conventional adhesives. Four types of the adhesives were exposed to combined environmental conditions over 1000 hours at an accelerated aging tester, which can simulate natural weather conditions such temperature, moisture and ultraviolet. Mechanical and chemical properties of the adhesives were evaluated through material testing system and FT/IR spectrometer. According to the results, the conventional adhesives can be replaced by the alternative adhesives because the alternative adhesives were more stable to environmental conditions rather than the conventional adhesives.