• The KIPS Transactions:PartA
• /
• v.9A no.1
• /
• pp.1-8
• /
• 2002

Most of the traditional embedded web server systems have been designed for monitoring and controlling some dedicated equipments. Hence, not only they have no generality and flexibility but also they are too expensive for the lower-cost domestic equipment. To cope with these difficulty, we suggest a lower-cost ${\mu}$-embedded web server model which is suitable for monitoring and controlling the industry or house equipments by using the internet. The suggested model is based on an one-chip ${\mu}$-processor in which the ISP (In-System Programming) function and flash ROM are embedded basically to minimize the cost of H/W and S/W. Also it allows to add an new function dynamically to provide the generality and flexibility. Finally, to evaluate the feasibility of the suggested model, we have manufactured a test-board based on the ATMega103 ${\mu}$-processor and programmed the control program and tested it on the MS Explorer 5.0 environment.

• Journal of muscle and joint health
• /
• v.3 no.1
• /
• pp.4-22
• /
• 1996

Purposes of this study were to identify a hospital-based home care model and to improve the physical, emotional and economical effectiveness of arthritic patients through medical and nursing team approach. The design in nonequivalent control group pretest-posttest design with matched samples in terms of age, sex and disease severity. Fifty two patients in each group were assigned in Seoul, Kyunggi, Kangwon and Kwangju. Before and after 6-month period of home care, level of pain, duration of morning stiffness, Richie Index, ADL, self efficacy, depression, cost expenditure were measured. Nine patients were excluded from the control group in the period of study because of denial of participation. Contents of home care provided to the experimental group include mainly distribution of prescribed drugs, 'assessment of patients' condition and side-reactions of drug. All of the information related to the home care patient were reported to the physician. On the bases of these data, the physician prescribe the specific drugs to each patient. Each patient visited the physician every 2 or 3 month for laboratory test. Patients assigned to the control group visited the outpatient clinic once a month as usual. Null hypotheses were selected because physicians concerned about the ineffective change of patients' conditions due to indirect communication with patients through nurses. Level of pain, Richie index, ADL, self-efficacy, depression, duration of morning stiffness and direct medical cost were the home care provided to them. If a family member accompany in a home care group can save 10,676 Won/month in Seoul, 34,000 Won/month in other districts. Other in-direct cost for transportation and meal can also be saved. In conclusion, those patients with low level of ADL, high level of pain and Richie index, living in the remote area definitely need the home care.

• Physical Therapy Korea
• /
• v.20 no.1
• /
• pp.18-27
• /
• 2013

The purpose of this study was to compare the ring lock type knee-ankle-foot orthosis (KAFO) with newly developed 4-bar linkage KAFO on the gait characteristics of persons with poliomyelitis clinically. This 4-bar linkage is the stance control type KAFO which provide the stability during stance phase and knee flexion during swing phase. Two subjects participated in this study voluntarily. We provided the customized 4-bar linkage KAFO then asked the subjects to walk in level surface and stairs under the two different KAFO conditions. The characteristics of gait in the persons with poliomyelitis were evaluated using a 3D motion analysis system and force plate. Additionally 6 minute walk test for physiological cost index were conducted using pulse oximeter to measure the energy consumption. In the results of this study, the differences of 4-bar linkage KAFO compared with ring lock type KAFO are as follows: (1) Walking speed, stride length, and step length on level increased in subjects, (2) The gait symmetry was improved by generated knee flexion and decreased pelvic external rotation on level and stairs walking, (3) Decreased vertical excursion of center of mass and pelvic elevation during swing phase was decreased on level, (4) Knee extension moment, hip flexion moment, hip and knee internal rotation moment of non-braced limb were decreased on level walking, (5) Walking speed in 6-minute walk test was increased and physiological cost index was decreased. These findings indicate that 4-bar linkage KAFO compared with ring lock type KAFO is effective in enhancing pattern, endurance, and energy consumption in level surface and stairs walking.

• Korean System Dynamics Review
• /
• v.2 no.2
• /
• pp.25-40
• /
• 2001

This paper describes the forecast of power plant construction in a competitive korean electricity market. In Korea, KEPCO (Korea Electric Power Corporation, fully controlled by government) was responsible for from the production of the electricity to the sale of electricity to customer. However, the generation part is separated from KEPCO and six generation companies were established for whole sale competition from April 1st, 2001. The generation companies consist of five fossil power companies and one nuclear power company in Korea at present time. Fossil power companies are scheduled to be sold to private companies including foreign investors. Nuclear power company is owned and controlled by government. The competition in generation market will start from 2003. ISO (Independence System Operator will purchase the electricity from the power exchange market. The market price is determined by the SMP(System Marginal Price) which is decided by the balance between demand and supply of electricity in power exchange market. Under this uncertain circumstance, the energy policy planners such as government are interested to the construction of the power plant in the future. These interests are accelerated due to the recent shortage of electricity supply in California. In the competitive market, investors are no longer interested in the investment for the capital intensive, long lead time generating technologies such as nuclear and coal plants. Large unclear and coal plants were no longer the top choices. Instead, investors in the competitive market are interested in smaller, more efficient, cheaper, cleaner technologies such as CCGT(Combined Cycle Gas Turbine). Electricity is treated as commodity in the competitive market. The investors behavior in the commodity market shows that the new investment decision is made when the market price exceeds the sum of capital cost and variable cost of the new facility and the existing facility utilization depends on the marginal cost of the facility. This investors behavior can be applied to the new investments for the power plant. Under these postulations, there is the potential for power plant construction to appear in waves causing alternating periods of over and under supply of electricity like commodity production or real estate production. A computer model was developed to sturdy the possibility that construction will appear in waves of boom and bust in Korean electricity market. This model was constructed using System Dynamics method pioneered by Forrester(MIT, 1961) and explained in recent text by Sternman (Business Dynamics, MIT, 2000) and the recent work by Andrew Ford(Energy Policy, 1999). This model was designed based on the Energy Policy results(Ford, 1999) with parameters for loads and resources in Korea. This Korea Market Model was developed and tested in a small scale project to demonstrate the usefulness of the System Dynamics approach. Korea electricity market is isolated and not allowed to import electricity from outsides. In this model, the base load such as unclear and large coal power plant are assumed to be user specified investment and only CCGT is selected for new investment by investors in the market. This model may be used to learn if government investment in new unclear plants could compensate for the unstable actions of private developers. This model can be used to test the policy focused on the role of unclear investments over time. This model also can be used to test whether the future power plant construction can meet the government targets for the mix of generating resources and to test whether to maintain stable price in the spot market.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.9
• /
• pp.1438-1443
• /
• 2001

The significance of the casting/forging process for reducing the production cost of large components is being noted in these days. This casting/forging process is a method of forging a workpiece preformed by casting into the final shape. In this study, the casting/forging process has been applied in manufacturing a large aluminum flange in order to reduce press capacity and material cost. Firstly, a hot compression test was performed with cast cylindrical billets in order to determine the optimum forging condition of the aluminum flange. The optimum range of forging temperature of Al 5083 was from 420$\^{C}$ to 450$\^{C}$. The suitable strain rate was 1.5 sec(sup)-1. The deformation amount of a preform of a preform in a forging process is a key role in the mechanical properties of casting/forging products. In order to find the change of mechanical properties according to effective stain of cast aluminum billets, a hot upsetting test were performed with rectangular blocks and then a uniaxial tensile test was performed with specimens cut from the upsetted billets. The tensile strength and the elongation of cast/upsetted aluminum billets were increased largely until the effective strain was 0.7. FE analysis was performed to determine the configurations of case preform and die for an aluminum flange. In the FE analysis, the forging load-limit was fixed 1500ton for low equipment cost. The cast preform was designed so that the effective stain around the neck of a flange exceeded 0.7. From the result of FE analysis, optimal configurations of the cast preform and the die were designed for a large flange. The filling and solidification analysis for a sound cast-preform was carried out with MAGMA soft. In the forging experiment for an aluminum flange, it was confirmed that the optimal configuration of the cast preform predicted by FE analysis was very useful. The cast/forged products using designed preform were made perfectly without any defects.

• Journal of Environmental Science International
• /
• v.29 no.11
• /
• pp.1015-1024
• /
• 2020

Using the waste(sand wastr and boiler ash) in fluidized bed inciverator, lightweight aggregate concrete was produced and a recycling plan was prepated. The first, the result of the leaching test shows that the waste fluid sand and boiler ash did not exceed the effluent standard. This indicates that there is no harmful effect for recycling. The second, in the lightweight aggregate test using waste fluid sand and boiler ash, the sample that combined cement, waste fluid sand, and sand showed the highest compressive strength, and the mix proportion was 10: 7: 3. Lightweight aggregate concrete that combined cement, waste fluid sand, boiler ash, and sand had a low compressive strength by and large. The third, the same results were identified in the relation between the content of SiO₂ and that of Na₂O. As the SiO₂ content is lowered, the overall viscosity and plasticity of the concrete also decrease, which is not a good condition to form concrete. As for Na₂O, as the content increases, the viscosity of the sample and the viscosity of the cement are remarkably lowered, and the strength of the finished concrete is lowered. Therefore, it was concluded that the higher the content of SiO₂ and the lower the content of Na₂O, the more suitable it is to mix with cement to produce concrete. Fourth, from the fluidized bed incinerator currently operated by company A in city B, a total of 14,188 tons/year were discharged as of 2016, including 8,355 tons/year of bottom ash (including waste fluid sand) and 5,853 tons/year of boiler ash. The cost for landfill bottom ash and boiler ash discharged is 51,000 won/ton, and the total annual landfill cost is 723,588,000 won/ year. Assuming that the landfill tax to be applied from the year 2018 is about 10,000 won/ton, and if there is no reduction in waste disposal charge, an additional landfill tax of 141,880,000 won/year will be imposed. Consequently, the sum total of the annual landfill cost will be 865,468,000 won/year. Therefore, if the entire amount is used for recycling, the annual savings of about 8.7 billion won can be expected.

• International Journal of Highway Engineering
• /
• v.13 no.3
• /
• pp.75-82
• /
• 2011

There is the uncertain period of the construction in case of the products meeting the quality standard of KS M 6080, the quality is degraded because of the abrasive loss of the paint caused by vehicle tires as the traffic amount increases and of the loss and detachment of the glass beads providing the retroreflective function. The abrupt degradation of visibility causes the high frequency of traffic accidents at night and increases the traffic accident rate. Additional supplementary construction induces the direct material and construction costs. As the more cost induction effect than the direct cost, the traffic jam caused by the additional construction increases the indirect social costs such as time cost and vehicle cost. Hence, the study is concerned with performing the abrasion resistance test based on the EN 1436 standard to check and improve the quality of various road marking materials resulting in improving the durability of road marking materials. However, even though the difference in the durability lifetime of resins(binders) is bibliographically or theoretically clear, there was no difference in the durability lifetime (retroreflectivity aspect) of the road marking paint using these binders. The reason is that the bonding of beads was very insufficient or that the cross density caused by crack or freshness was low. Moreover, the measured wet retroreflectivity was distributed as the Rw3 or higher class in average on the basis of EN 1436 but was very insufficient on the basis of the minimum wet threshold retroreflectivity with 100mcd/($m^2{\cdot}lx$) managed overseas.

• International Journal of Highway Engineering
• /
• v.16 no.6
• /
• pp.159-167
• /
• 2014

PURPOSES : The purpose of this study is to analyze the requirements of the road traffic safety moderator robot when road repairing. The road traffic safety moderator robot is road traffic safety equipment and to conversions mechanical engineering and IT when road repairing. METHODS : The study used AHP based on the survey from road repair related expert that field engineers, design engineers, public officials and professors. The survey used paired comparison. The survey items were safety, convenience and economics. The safety is classified as visibility or efficiency, the convenience is classified as utility or mobility and the economics is classified as initial investment cost or maintenance $ management cost. The survey alternatives were the road traffic safety moderator robot, traffic regulation by human, traffic regulation by mannequin and traffic signs. The software for AHP is Expert Choice 2000. RESULTS : The results of AHP analyze, the weighted value of safety was analyzed with the highest at 0.488 of survey items. The weighted value of convenience was analyzed at 0.295, the weighted value of economics was analyzed at 0.218. The results of the road traffic safety moderator robot, the weight value of efficiency and utility were analyzed with the highest at 0.284 and 0.259 of alternatives. The weighted value of initial investment cost and maintenance & management cost were analyzed with the lowest at 0.203 and 0.211 of alternatives. The consistency test results of each items, null hypothesis is rejected because the CR values were 0.000 respectively. Therefore, the study results are consistency. CONCLUSIONS : The result of this study, overall value of the road traffic safety moderator robot came off second-best of other alternatives. The road traffic safety moderator robot has been received highest praise by the result of the study as good road traffic safety equipment when road repairing because the weighted values of efficiency and utility were analyzed with the highest of survey items. The efficiency mean securing safety and the utility mean practical assistance when road repairing. The results of this study showed that the road traffic safety moderator robot will effective for traffic safety when road repairing. economics and visibility are that supplementation of the road traffic safety moderator robot because the weighted values of economics and visibility were analyzed with the lowest of survey items. The consistency test results are consistency because the CR values were 0.000 respectively.

• The KIPS Transactions:PartA
• /
• v.11A no.5
• /
• pp.391-400
• /
• 2004

Within multimodal medical image registration techniques, which correlate different images and Provide integrated information, surface registration methods generally minimize the surface distance between two modalities. However, the features of two modalities acquired from one subject are similar. So, it can improve the accuracy of registration result to match two images based on optimization of both surface distance and shape feature. This research proposes a registration method which optimizes surface distance and surface curvature of two brain modalities. The registration process has two steps. First, surface information is extracted from the reference images and the test images. Next, the optimization process is performed. In the former step, the surface boundaries of regions of interest are extracted from the two modalities. And for the boundary of reference volume image, distance map and curvature map are generated. In the optimization step, a transformation minimizing both surface distance and surface curvature difference is determined by a cost function referring to the distance map and curvature map. The applying of the result transformation makes test volume be registered to reference volume. The suggested cost function makes possible a more robust and accurate registration result than that of the cost function using the surface distance only. Also, this research provides an efficient means for image analysis through volume visualization of the registration result.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.2
• /
• pp.97-104
• /
• 2010

This study evaluated the energy efficiency of a windows system using built-in blinds, with regard to their insulation performance and their blocking of solar radiation. The study took advantage of the "Physibel Voltra" program as a physical simulation of heat transfer. To simulate the "Physibel Voltra" program, I practiced a mock-up test to determine heating quality and translation condition. I analyzed the propensity to annual energy consumption, the annual quantity of heat transfer, and the annual cooling and heating cost through a computer simulation for one general household in an apartment building. In the test, it was found that compared to a general windows system, a windows system with built-in blinds reduced the annual heat transfer by 10% in cooling states and by 11% in heating states when the blind was up. When the blind was down, the windows system with built-in blinds reduced the annual heat transfer by 25% in cooling states and 30% in heating states. When a windows system with built-in blinds is compared with a general windows system, the quantity of cooling and heating loads is reduced by 283.3kw in cooling states and 76.3kw in heating states. This leads to a reduction in the required cooling and heating energy of 359.6kw per house. It is thus judged that the use of a windows system with built-in blinds is advantageous in terms of reducing greenhouse gas emissions, because the annual TOE (tons of oil equivalent) per house is reduced by 0.078TOE, while $tCO_2$ is reduced by $0.16tCO_2$. In addition, compared with a general windows system, the cost of cooling and heating loads in the system reduces the annual cooling cost by 100,000won, and the annual heating cost by 50,000won. Ultimately, this means that cooling and heating loads are cut by 150,000won per year.