• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.1
• /
• pp.239-249
• /
• 2003

The bridges, which were built between 20 and 30 years ago in rural area, have to support unexpected overload caused by excessive amount of transportation. For these rural bridges, repairs and replacements are needed. To avoid the high cost of rehabilitation, the bridge rating must correctly report the present load-carrying capacity. Rating engineers use Allowable Stress Design (ASD), Load Factor Design (LFD), and Load Resistance Factor Design (LRFD) to evaluate the bridge load carrying capacity. In this paper, the load rating methods are introduced, and it is illustrated how to use the load test data from literature survey. Load test is conducted to the bridge that was built 30 years ago in rural area. From load test results, new maintenance strategy is suggested instead of the bridge replacement.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.640-648
• /
• 2009

Recently the truction of coastal reclaimation work has been extensively implemented in Korea. The Sondo New City is being established on the reclaimed land from the sea, construction companies of metro construction are planing to pull-out the sheet pile for saving the construction cost. In the case of soft marine clay, it is very difficult to pull-out the sheet pile by using the hydraulic hammer difficult. Therefore, the man of the field must be aware of vibration effect to the ground and the structure. For understanding the vibration effect to the ground during subway construction, the model was formulated with 1/25 braced-cut for subway construction. Scott and Iai(1989) proposed the law of the similarity for other experimental conditions. The laboratory model test was conducted under the vibration condition of sheet pile pulling out. The settlement on the ground surface was measured during the shaking table test. The pore water pressure was also monitored in the upper, middle, and lower layers of soil. The field settlement level and the pore water pressure can be predicted by using the results of the laboratory shaking table test.

• Electrical & Electronic Materials
• /
• v.10 no.4
• /
• pp.349-354
• /
• 1997

This paper aims at studying the improvement of test method for t-weight sensitive fault (t-wsf) detect. The development of RAM fabrication technology results in not only the increase at device density on chips but also the decrease in line widths in VLSI. But, the chip size that was large and complex is shortened and simplified while the cost of chips remains at the present level, in many cases, even lowering. First of all, The testing patterns for RAM fault detect, which is apt to be complicated , need to be simplified. This new testing method made use of Local Lower Bound (L.L.B) which has the memory with the beginning pattern of 0(l) and the finishing pattern of 0(1). The proposed testing patterns can detect all of RAM faults which contain stuck-at faults, coupling faults. The number of operation is 6N at 1-weight sensitive fault, 9,5N at 2-weight sensitive fault, 7N at 3-weight sensitive fault, and 3N at 4-weight sensitive fault. This test techniques can reduce the number of test pattern in memory cells, saving much more time in test, This testing patterns can detect all static weight sensitive faults and pattern sensitive faults in RAM.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.132-135
• /
• 2007

In this study, hydroformability and mechanical properties of pre- and post- heat treated Al6061 tubes at different extrusion type were investigated. For the investigation, as-extruded, full annealed and T6-treated Al6061 tubes at different extrusion type were prepared. To evaluate the hydroformability, uni-axial tensile test and free bulge test were performed at room temperature and $250^{\circ}C$. Also mechanical properties of hydroformed part at various pre- and post-heat treatments were estimated by tensile test. And the tensile test specimens were obtained from hexagonal prototype hydroformed tube at $250^{\circ}C$. As for the heat treatment, hydroformability of full annealed tube is 25% higher than that of extruded tube. The tensile strength and elongation were more than 330MPa and 12%, respectively, when hydroformed part was post-T6 treated after hydroforming of pre- full annealed tube. However, hydroformed part using T6 pre treated tube represents high strength and low elongation, 8%. Therefore, the T6 treatment after hydroforming for as-extruded tube is cost-effective. Hydroformability of Al6061 tube showed similar value for both extrusion types. But flow stress of seam tube showed $20{\sim}50MPa$ lower value.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.5
• /
• pp.703-712
• /
• 2014

To improve the efficiency and safety of railway systems, the train control system has been considerably evolved from the ground-equipment-based control system (e.g. track circuit, interlocking system, etc.) into the on-board-equipment-based control system. In addition, this train control system enables the rolling stock to intelligently control the trackside facilities by introducing the information and communication technologies (ICT). Accordingly, since the ICT-based train control system makes the railway system be simplified (i.e. the heavy ground-equipment can be removed), the efficient and cost-effective railway system can be realized. In this paper, we perform the feasibility test of the ICT-based train control system via a simulation. To this end, we have developed the prototypes of the on-board controller and wayside object control units which control the point and crossing gate and performed the integrated operation simulation in a testbed. In this paper, before the field test of the on-board-controller-based train control system, we perform the Consecutive operation test for prototypes of the on-board controller, wayside object control units and local control computer.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.635-641
• /
• 2004

This paper presents a new low-cost RF Built-In Self-Test (BIST) circuit for measuring transducer voltage gain, noise figure and input impedance of 5.25GHa low noise amplifier (LNA). The BIST circuit is designed using 0.18${\mu}{\textrm}{m}$ SiGe technology. The test technique utilizes input impedance matching and output transient voltage measurements. The technique is simple and inexpensive. Total chip size has additional area of about 18% for BIST circuit.

• Journal of Information Processing Systems
• /
• v.13 no.5
• /
• pp.1089-1102
• /
• 2017

In software systems, it has been observed that a fault is often caused by an interaction between a small number of input parameters. Even for moderately sized software systems, exhaustive testing is practically impossible to achieve. This is either due to time or cost constraints. Combinatorial (t-way) testing provides a technique to select a subset of exhaustive test cases covering all of the t-way interactions, without much of a loss to the fault detection capability. In this paper, an approach is proposed to generate 2-way (pairwise) test sets using genetic algorithms. The performance of the algorithm is improved by creating an initial solution using the overlap coefficient (a similarity matrix). Two mutation strategies have also been modified to improve their efficiency. Furthermore, the mutation operator is improved by using a combination of three mutation strategies. A comparative survey of the techniques to generate t-way test sets using genetic algorithms was also conducted. It has been shown experimentally that the proposed approach generates faster results by achieving higher percentage coverage in a fewer number of generations. Additionally, the size of the mixed covering arrays was reduced in one of the six benchmark problems examined.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.5
• /
• pp.959-961
• /
• 2011

Manure-based composts can have detrimental effects on the agricultural lands and crops if they are applied without proper stabilization process. Composting is well-known method for the stabilization of manure-based composts and the extent of composting could be examined by maturity test. Among various methods to examine compost maturity, the performances of two mechanical methods (Solvita and CoMMe-100) were examined and the test results were compared with seed germination test. The mechanical methods are considered to be simple and relatively objective. Also they are cost- and time-efficient. Ten commercially available composts collected in Korea were used for this study. Basically, the maturity determined with these mechanical methods was in good agreement with the seed germination test. However, it appeared that the index levels of compost maturity indicated more maturity by CoMMe-100 than Solvita for the same compost. The differences between maturity index levels determined by both methods were able to be minimized through extending the reaction time for CoMMe-100 and adjusting index level for maturity determination in the standard color chart.

• Advances in aircraft and spacecraft science
• /
• v.6 no.5
• /
• pp.427-442
• /
• 2019

Small satellites represent an emerging opportunity to realize a wide range of space missions at lower cost and faster delivery, compared to traditional spacecraft. However, small platforms, such as CubeSats, shall increase their actual capabilities. Miniaturized electric propulsion systems can provide the satellite with the key capability of moving in space. The level of readiness of miniaturized electric propulsion systems is low although many concepts have been developed. The present research intends to build a flexible test platform for the assessment of selected small propulsion systems in relevant environment at laboratory level. Main goal of the research is to analyze the mechanical, electrical, magnetic, and chemical interactions of propulsion systems with the modern CubeSat-technology and to assess the performance of the integrated platform. The test platform is a 6U CubeSat hosting electric propulsion systems, providing mechanical, electrical and data interfaces, able to handle a variety of electric propulsion systems, thanks to the ability to regulate and distribute electric power, to exchange data according to several protocols, and to provide different mechanical layouts. The test platform is ready to start the first verification campaign. The paper describes the detailed design of the platform and the main results of the AIV activities.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.1
• /
• pp.55-60
• /
• 2022

This study conducted the measurements of air flow rate for blower systems with experiment and numerical. A new airflow rate test method is suggested, with which it is possible to accurate measurements and calculate the air flow rate for blower systems. The blower(axial fan) is an industrial fluid machine device that supplies a large amount of air by driving an impeller with an electric motor, and it is widely used throughout the industry such as steel, power plant, chemical, semiconductor, LC D, food, and cement. The airflow from the blower is for exchanging the heat in the cooling unit or heat exchanger. The temperature of coolants and hydraulic oil primarily depends on the amount of airflow rate through the cooling package so its accurate estimation is very important. Moreover, it required a larger investment in time and cost since it could not be executed until the system is actually made. Therefore, this research is intended to examine the phenomenon of air flow pattern when testing air flow rate, suggested new test method, and show the result of the validation test.