• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.55-62
• /
• 2012

The development of memory design and process technology enabled the production of high density memory. As the weight of embedded memory within aggregate Systems-On-Chips(SoC) gradually increases to 80-90% of the number of total transistors, the importance of testing embedded dual-port memories in SoC increases. This paper proposes a new micro-code based programmable memory Built-In Self-Test(PMBIST) architecture for dual-port memories that support test various test algorithms. In addition, various test algorithms including March based algorithms and dual-port memory test algorithms are efficiently programmed through the proposed algorithm instruction set. This PMBIST has an optimized hardware overhead, since test algorithm can be implemented with the minimum bits by the optimized algorithm instructions.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.10a
• /
• pp.85-90
• /
• 1995

A characteristic transport theory code CRX is developed and tested for cell and assembly calculations. Since the characteristic method treats explicitly (analytically) the streaming portion of the transport equation, CRX treats strong absorbers well and has no practical limitations placed on the geometry of the problem. To test the code, it was applied to three benchmark problems which consist of complex meshes and compared with other codes.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1376-1379
• /
• 1996

In this paper a GPS receiver is developed using commercial chipsets. GP2010 RF front end and GP2021 Multi-channel correlator of GEC PLESSY are adapted in designing the receiver hardware. MC 68340 is used for controlling the correlator GP2021 and implementing the navigation processing. Also presented are some test results of the developed receiver whose software has an interrupt driven structure rather than common real-time kernel based structure.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05a
• /
• pp.28-33
• /
• 1996

A transport theory code CRX-Hex based on characteristic methods with a general geometric tracking routine is developed for the heterogeneous hexagonal geometry. With the general geometric tracking routine, the formulation of the characteristic method is not changed. To test the code, it was applied to two benchmark problems which consist of complex meshes and compared with other codes (HELIOS, TWOHEX).

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.1
• /
• pp.272-287
• /
• 2017

This paper proposes new methods, named Derivative Code (DerivativeCode) and Derivative Code Pattern (DCP), for object recognition. The discriminative derivative code is used to capture the local relationship in the input image by concatenating binary results of the mathematical derivative value. Gabor based DerivativeCode is directly used to solve the palmprint recognition problem, which achieves a much better performance than the state-of-art results on the PolyU palmprint database. A new local pattern method, named Derivative Code Pattern (DCP), is further introduced to calculate the local pattern feature based on Dervativecode for object recognition. Similar to local binary pattern (LBP), DCP can be further combined with Gabor features and modeled by spatial histogram. To evaluate the performance of DCP and Gabor-DCP, we test them on the FERET and PolyU infrared face databases, and experimental results show that the proposed method achieves a better result than LBP and some state-of-the-arts.

• Nuclear Engineering and Technology
• /
• v.49 no.5
• /
• pp.928-940
• /
• 2017

An experiment using the $Prim{\ddot{a}}rkreisl{\ddot{a}}ufe$ Versuchsanlage (PKL) was performed for the OECD/NEA PKL-3 Project as a counterpart to a previous test with the large-scale test facility (LSTF) on a cold leg smallbreak loss-of-coolant accident with an accident management (AM) measure in a pressurized water reactor. Concerning the AM measure, the rate of steam generator (SG) secondary-side depressurization was controlled to achieve a primary depressurization rate of 200 K/h as a common test condition; however, the onset timings of the SG depressurization were different from each other. In both tests, rapid recovery started in the core collapsed liquid level after loop seal clearing, which caused whole core quench. Some discrepancies appeared between the LSTF and PKL test results for the core collapsed liquid level, the cladding surface temperature, and the primary pressure. The RELAP5/MOD3.3 code predicted the overall trends of the major thermal-hydraulic responses observed in the LSTF test well, and indicated a remaining problem in the prediction of primary coolant distribution. Results of uncertainty analysis for the LSTF test clarified the influences of the combination of multiple uncertain parameters on peak cladding temperature within the defined uncertain ranges.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.159-169
• /
• 2008

In general, it is considered that a pillar between closely-spaced tunnel is sensitive for stress concentration. Stability of a pillar is key factor for excavation of closely-spaced tunnel. In this paper, the study is focused on tracing the behaviors, displacement and plotting damages around tunnels that is modelled with Particle Flow Code, $PFC^{2D}$. Parametric study was performed with changing distance between center of tunnels and coefficient of earth pressure(K). Scaled-model tests were also carried out to validate a numerical analysis model. It was found that $PFC^{2D}$ could show dynamic visualized result in quite good agreement with the experimental test.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.635-640
• /
• 2000

This paper describes an experimental investigation on the influence of concrete strength on tension stiffening behavior. Total 6 direct tension specimens were tested with variation of concrete strengths such as 260, 620, and 820kgf/$\textrm{cm}^2$. These test results were compared with tension stiffening models of CEB-FIP Model Code. It was appeared that, as concrete strength was increasing, CEB-FIP models estimated much more tension stiffening than these test results. As the result, it would be said that the influence of concrete strength on tension stiffening was not properly taken account for in CEB-FIP model.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.1
• /
• pp.67-71
• /
• 2012

The optical properties of PDP, such as the transmittance and reflectance, were analyzed with 3D optical code. Three different ITO-less structures in the front panel are examined. In the assembled panel study, the test 1 structure shows 16.6% and 10.2% higher reflectance than the structures of tests 2 and 3, respectively. In order to check the validation of the simulation result, three 7.5-inch test panels having the same geometry and property are fabricated as simulation models. The calculated reflective properties are compared to the measured data from real panels. The relative difference extracted from the simulation and measurement methods is less than 4.9% and are well matched.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05a
• /
• pp.713-718
• /
• 1998

Henry-Fauske critical flow model was incorporated into TRAC-PF1 to correct some errors in the original TRAC-PFI critical flow model. Henry-Fouske mode1 was numerically implemented and tested against steady-state steam-water experimental data. The model was incorporated into TRAC-PFI and code assessment against Marviken Critical Flow Tests 15 and 24 was carried out. Calculations using RELAP5/MOD3 were also made for comparison. Ten cases were calculated each test and sensitivity study on nodalization as well as critical flow or model was performed Stand-alone numerical model test and code assessment were done for verification and validation of code modification. Calculation results show that the modified version of TRAC-PF1 has a capability to model critical flow correctly in various conditions.