• Journal of Veterinary Science
• /
• v.24 no.2
• /
• pp.32.1-32.10
• /
• 2023

Background: The association between vitamin D and canine keratoconjunctivitis sicca (KCS) has not been investigated in dogs. Objectives: To investigate the association of serum 25-hydroxyvitamin D [25(OH)D] concentrations with Schirmer tear test 1 (STT-1) and tear film breakup time (TFBUT) in dogs. Methods: Sixty-one clinically healthy, client-owned dogs were enrolled. STT-1 and TFBUT were measured in 122 (61dogs) and 82 (41 dogs out of total 61 dogs) eyes, respectively. Serum 25(OH)D concentrations were evaluated by quantitative chemiluminescent immunoassay. The dogs were classified into 6 groups according to the evaluations (STT-1: group 1, normal [≥ 15 mm/min] in both eyes; group 2, normal in one eye and abnormal [< 15 mm/min] in the fellow eye; group 3, abnormal in both eyes; TFBUT: group 4, normal [≥ 20 sec] in both eyes; group 5, normal in one eye and abnormal [< 20 sec] in the fellow eye; group 6, abnormal in both eyes). Results: STT-1 was positively correlated with TFBUT (p < 0.001). Among the STT-1 groups, the mean serum 25(OH)D concentration in group 1 was significantly higher than in groups 2 and 3 with positive correlation (p < 0.001). However, there were no significant differences among the TFBUT groups 4, 5, and 6. Conclusions: In dogs, it was found that serum 25(OH)D concentrations had a greater effect on quantitative KCS than qualitative KCS. Therefore, it is considered that measurement of serum 25(OH)D concentration could be included in the diagnostic tests in canine quantitative KCS patients.

• Toxicological Research
• /
• v.14 no.2
• /
• pp.205-209
• /
• 1998

To evaluate immunotoxicity of skin decontamination kit(SDK) newly-developed in Agency for Defense Development(ADD), delayed contact hypersensitivity (maximization) test and passive cutaneous anaphylaxis(PCA) test of SDK were performed and the results were compared with those of M 291. In maximization test, sensitization reaction was induced by id injection (2.5 mg / 0.1 $\textrm{m}{\ell}$/ guinea pig or 2.5 mg+CFA/0.1 $\textrm{m}{\ell}$/guinea pig) and topical application (2.5 mg/$\textrm{m}{\ell}$/guinea pig) with SDK or M291 at an interval of 1 week, and 2 weeks later, challenged by topical application with 25 mg/$\textrm{m}{\ell}$/guinea pig. SDK and M291 did not induce any reactions, showing 0 point of sensitization score and 0% of sensitization rate. In conclusion, it is suggested that SDK and M291 do not induce delayed contact hypersensitivity. In PCA test, rats were administered id with mouse anti-SDK serum and challenged iv with a mixture of antigen SDK and Evan's blue. SDK did not induce blue spots at the injection sites of both high (2.5 mg/mouse) and low (1.25 mg/mouse) dose-induced antisera. In contrast, BSA, positive control produced spots larger than 5 mm in diameter at the injection sites of BSA-induced antiserum up to $2^2$ ~ $2^4$dilution. In conclusion, it is suggested that SDK do not induce IgE production and is not a PCA-reaction inducer.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.34 no.1
• /
• pp.1-10
• /
• 2022

In this study, the two horizontal shroud tidal current energy converter, which can generate power even under low flow speed conditions, was developed. In order to determine the shape of the shroud system, a three-dimensional numerical simulation test was conducted, and a 1/6 scale down model was made to perform a hydraulic model experiment. The hydraulic model experiment was performed under four flow conditions, and the flow speed, torque, and RPM were measured for each experimental case. As a result of the numerical simulation test, it was found that the flow speeds passing through the nozzle were increased by about 2~3 times in the cylinder, and when the extension ratio was 2:1, the highest flow speed was shown. In addition, it was found that the flow speeds increased 2.8 times when the diameter ratio between the nozzle and the cylinder was 1.5:1. Meanwhile, as a result of the hydraulic model experiment, it was found that when the tip speed ratio was between 1.75 and 2, the power coefficient was 0.32 to 0.34.

• Journal of Preventive Medicine and Public Health
• /
• v.53 no.4
• /
• pp.245-255
• /
• 2020

Objectives: This study examined associations among social capital indicators (social participation and generalized trust) at the individual level and alcohol use, which was quantified using Alcohol Use Disorders Identification Test (AUDIT) scores. Methods: In total, there were 8800 participants in community health interviews, including 220 adults sampled systematically from a resident registration database of each of 40 sub-municipal administrative units of local (city or county) governments. Adjusted odds ratios (aORs) and 95% confidence intervals (CIs) were calculated using polychotomous logistic regression. Results: The aORs for abstainers versus people with AUDIT scores of 0-7, based on 3 questions on generalized trust, in comparison to those with no positive responses, were 1.15 (95% CI, 0.99 to 1.34) for 1 positive response, 1.16 (95% CI, 0.98 to 1.37) for 2 positive responses; and 1.39 (95% CI, 1.20 to 1.61) for 3 positive responses. The aORs for abstainers versus people with AUDIT scores of 0-7, in comparison to participation in no organizations, were 0.61 (95% CI, 0.54 to 0.69) for participation only in informal organizations; 2.16 (95% CI, 1.57 to 2.99) for participation only in religious organizations; 2.41 (95% CI, 1.10 to 5.29) for participation only in volunteer organizations; and 0.65 (95% CI, 0.57 to 0.74) for participation in formal organizations. Participants in formal social organizations, regardless of their participation in informal organizations, were more likely to have AUDIT scores of 8-15 (aOR, 1.29; 95% CI, 1.04 to 1.60) or ≥16 (aOR, 1.65; 95% CI, 1.22 to 2.23) than to have scores of 0-7. Conclusions: Our findings may have implications for health policy to reduce alcohol problems.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.2
• /
• pp.10-21
• /
• 1998

In this paper, we analyze the problems of conventional and previous mehtod on delay test method in IEEE 1149.1. To solve them, we propose two kinds of delay test architectures. One is called ARCH-C, is for combinatonal circuit, and the other is ARCH-S, for clocked sequential circuit. ARCH-C is able to detect delay defect of 0.5 $T_{tck}$ or 1 $T_{tck}$ size. And ARCH-C have a fixed and small amount of hardware overhead, on the contrary preious method has a hardware overhead on the dependent of CUT. This paper discusses weveral problems of Delay test on IEEE 1149.1 for clocked sequential circuit. We suggest the method called ARCH-S, is based on a clock counting technique to generate continuous clocked input of CUT. the simulation results ascertain the accurate operation and effectiveness of the proposed architectures.res.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.7
• /
• pp.635-643
• /
• 2017

The purpose of this study is to investigate the influence of the cold reduction rate and an ultrasonic fatigue test (UFT) on the fatigue behaviors of STS 304L. The tensile strength, yield strength, hardness value and fatigue limit in the UFT fatigue test linearly increased as thickness decreased from 1.5 mm to 1.1 mm, as the cold reduction rate of STS 304L increased. As a result of the UFT fatigue test (R = -1) of four specimens, the fatigue limit of the S-N curve formed a knee point in the region of $10^6$, and the 2nd fatigue limit caused by giga cycle fatigue did not appeared. In the case of t = 1.1 mm, the highest fatigue limit was 345 MPa, which was 64.3% higher than the original material (t = 1.5 mm). As a result of the UFT fatigue test of STS 304L, many small surface cracks occurred, grown, coalesced while tearing.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.4
• /
• pp.421-431
• /
• 2006

Statement of problem : Accurate impression is essential to success of implant prostheses. But there have been few studies about the accuracy of fixture-level impression technique in internal connection implant system. Purpose: This study evaluated the accuracy of splinted fixture-level impression technique using clinical methods and the effect of internal hex on fit of superstructure in internal connection implant system (Astra Tech). Material and method : Two metal master frameworks made from two abutments (Cast-to Abutment ST) each for parallel and divergent conditions and a corresponding. passively fitting, dental stone master cast with four future replicas (Fixture Replica ST) were fabricated. Ten dental stone casts were made with vinyl polysiloxane impressions from the master cast by acrylic resin splinted fixture-level impression technique. To evaluate the accuracy of impression technique, the fit of master frameworks for test models was evaluated using screw resistance test (SRT) and one-screw test. The results of SRT were recorded as SRT values from grade 1 to grade 5 by 1/4 turn. And to evaluate the effect of hex on fit of superstructure, the same tests were performed after removing hexes of master frameworks. Results: 1. There was only one case (2.5%) showing SRT value of test model below ade 2 in total before and after removing hexes of master frameworks. And, by removing hexes. SRT values decreased in only one test model (5%) and did not change in 17 test models (85%). 2. SRT values of the 1$^{st}$ screws were grade 2 in 80% of cases before, and grade 1 in 80% of cases after removing hexes. And, by removing hexes, SRT values decreased in 72.5% of cases. 3. SRT values of the 2$^{nd}$ screws were grade 3 in 85% of cases before, and grade 3 in 95% of cases after removing hexes. And, by removing hexes, SRT values did not change in 85% of cases. 4. There were only 2 cases regarded as acceptable fit by one-screw test, and SRT values of 2$^{nd}$ screws of both cases were grade 2. Conclusion. Within the limitations of this study, future-level impression of internal connection implant system is considered to obtain inaccurate working cast, even using acrylic resin splinted impression technique. And, it is considered to be unable improve the fit to remove the hexes of implant restoration.

• Journal of Energy Engineering
• /
• v.27 no.4
• /
• pp.1-12
• /
• 2018

The code and standards related to fuel cells were analyzed to derive the SOFC(Solid Oxide Fuel Cell) stack safety performance evaluation items and evaluation methode. Safety performance evluation of the SOFC stack was tested by quoting derived test items. The stack used in the test is an anode-supported type 2 Cell stack (Active surface area : 220cm) manufactured by MICO Inc, and SOFC stack safety performance evaluation system used for the test is self-manufactured. We conducted a leakage test, current voltage characteristic test, rated output test, and power response characteristics test. In the safety performance evaluation test, the stack showed no gas leakage, the maximum output and rated output was recorded to 65.6 W(1.41 V, 46.5 A, $422mA/cm^2$), 62.3 W(1.57 V, 40 A, $363mA/cm^2$). In the power response characteristics test verified that the output is kept stable within two seconds. At the maximum load (40 A) and the minimum load (8 A), the output was recorded 62 W and 16W in $750^{\circ}C$. This study will contribute to the universalization and to provide much safe environment of operating the solid oxide fuel cell system.

• Journal of Veterinary Clinics
• /
• v.35 no.3
• /
• pp.93-96
• /
• 2018

This study aimed to establish an injection protocol to determine the precise CT scan timing in canine abdominal multi-phase CT using the test bolus method. Three dynamic scans with different contrast injection parameters were performed using a crossover design in eight normal beagle dogs. A contrast material was administered at a fixed dose of 200 mg iodine/kg as a test bolus for dynamic scans 1 and 2, and 600 mg iodine/kg as a main bolus for dynamic scan 3. The contrast materials were administered with 1 ml/s in dynamic scan 1, and 3 ml/s in dynamic scan 2 and 3. The mean arrival time to the appearance of aortic enhancement in dynamic scan 3 was similar to that in dynamic scan 2, and different significantly to that in dynamic scan 1. The mean arrival time to the peak aortic and pancreatic parenchymal enhancement in dynamic scan 3 was similar to that in dynamic scan 1, and different significantly to that in dynamic scan 2. In multi-phase CT scan, a test bolus should be injected with the same injection duration of a main bolus, to obtain the precise arrival times to peak of arterial or pancreatic parenchymal enhancement.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.10 no.2
• /
• pp.125-138
• /
• 2008

For physical and hand property evaluation of fabrics, the knitted fabrics from 11 types of machines knitting fancy yarns, boucle (M1), knot (M2), snarl (M3), and slub (M4), tamtam (M5), tubular (M6), fur 1 (M7), bead (M8), fur 2 (M9), fur 3 (M10), and ladder (M11) yarns, were prepared with 7-10 G plain stitch. Washing test and pilling test had also been carried out. For hand properties by objective sensibility evaluation, 17 items of sir mechanical properties using KES-FB (Kawabata Evaluation System) had been measured. Then hand values of knitted fabrics were calculated with a calculation formula, namely KN-402-KT. Finally the total hand values were obtained through KN-301-WINTER. As a result of physical properties and objective evaluation for machines knitting fancy fabrics, most of them shrank in the direction of wale and course after the washing test, in which their shrinkage rate had a maximum of 3.5%. Therefore, the washing test indicated that the shrinkage ratio of knitted fabrics had a minor change. The results of the pilling test are mostly 4-5th grade, and all of the machines knitting fancy fabrics showed good results in the pilling resistance. In hand properties and objective sensibility evaluation, twisted fancy yarns, such as boucle (M1), knot (M2), snarl (M3), and slub (M4), were superior to bonding rigidity (B) and shear rigidity (G). The surface property between course and wale differs in all samples and course direction is tougher than wale direction. FUKURAMI (fullness and softness) of all samples have high values, besides NUMERI (smoothness) of tamtam (M5) and boucle (M1), which were rather good. Most samples except fur 1 (M7) had low KOSHI (stiffness) value. The total hand value (THV) of twisted yarns was low. This study proves that manufacturers, who plan knitting yarn products and knit fashion, can apply these data to develop machines knitting yarns and knits that fit the consumers' demands.