• 한국염색가공학회지
• /
• 제9권4호
• /
• pp.7-19
• /
• 1997

The purpose of the study was to investigate the shrinkage and creep behavior of PET filaments which were prepared at various spinning speeds(3,300, 4,000, 5,000, 6,000, and 7,000m/min) and anneal($120^{\circ}$, 30min & $150^{\circ}$, 40min). In order to determine the shrinkage and creep behavior with the crystallinity change, PET filaments were treated with low(12$0^{\circ}C$, 30min) and high($150^{\circ}$, 40min) temperature conditions with hot air dryer under the constant tension. The results of the study were as follows: as the spinning speed increased, the degree of shrinkage and elongation of the sample treated by wet condition decreased. The sample with 0.01g/d of load under various spinning speeds showed shrinkage behavior and highest shrinkage ratio at $76^{\circ}$ which was Tg of PET. The degree of shrinkage and elongation of the treated sample was less than those of the untreated sample by wet treatment. Especially, there was less degree of shrinkage and elongation of the sample treated by higher temperature condition. In 3,300m/min of spinning speed the draw ratio of undrawn yarn of a mixture of a-axis orientation and c-axis orientation was 2.0, which is similar to the value of the traditional drawn yarn. Finally, there was a big range of shrinkage and elongation by wet treatment in 3,300 m/min of spinning speed.

• 공업화학
• /
• 제10권6호
• /
• pp.809-813
• /
• 1999

D상 유화법을 적용하고 상도를 이용하여 유화메커니즘을 설명하였다. D상 유화작용은 등방성 계면활성제 용액의 형성과 함께 시작되며 계면활성제 용액에 octamethyl cyclotetrasiloxane(OMCS)의 분산으로 계면활성제중 오일(O/D) 겔 유화물의 형성에 의해 진행된다. 폴리올은 이 실험목적상 필수성분이다. 폴리올의 기능을 이해하기 위해 비이온 계면활성제/오일/물/폴리올계의 용액거동을 폴리옥시에틸렌올레일에테르/OMCS/프로필렌글리콜(PG)의 수용액인 3성분의 상도를 이용하여 조사하였다. 등방성 계면활성제상에서 오일의 용해도는 PG를 가함에 따라 증가하였다. D상 유화물은 OMCS의 농도가 70~90% 범위에서와 계면장력이 2.0~3.0 dyne/cm 범위에서만 형성되었으며, D상 유화물은 $10{\mu}m$ 정도 크기의 균일한 구상으로 O/W 형이었다.

• Journal of Trauma and Injury
• /
• 제23권2호
• /
• pp.175-179
• /
• 2010

Purpose: Sternal fractures after blunt thoracic trauma can cause significant pain and disability. They are relatively uncommon as a result of direct trauma to the sternum and open reduction is reserved for those with debilitating pain and fracture displacement. We reviewed consecutive 11 cases of open reduction and fixation of sternum and tried to find standard approach to the traumatic sternal fractures with severe displacement. Methods: From December 2008 to August 2010, the medical records of 11 patients who underwent surgical reduction and fixation of sternum for sternal fractures with severe displacement were reviewed. We investigated patients' characteristics, chest trauma, associated other injuries, type of open reduction and fixation, combined operations, preoerative ventilator support and postoperative complications. Results: The mean patient age was 59.3years (range, 41~79). The group comprised 6 male and 5 female subjects. Among 11 patients who underwent open reduction and fixation for sternal fracture with severe displacement, 6 cases had isolated sternal fractures and the other 5 patients had associated other injuries. Sternal fractures were caused by car accidents (9/11, 81.8%), falling down (1/11, 9.1%) and direct blunt trauma to the sternum (1/11, 9.1%), respectively. 3 of the 7 patients (42.9%) who underwent sternal plating with longitudinal plates showed loosening of fixation. Otherwise, none of the 4 patients who underwent surgical fixation using T-shaped plate had stable alignment of the fracture. Conclusion: Sternal fractures with severe displacement need to be repaired to prevent chronic pain, instability of the anterior chest wall, deformity of the sternum, and even kyphosis. In the present study, a T-shaped plate with a compression-tension mechanism constitutes the treatment of choice for displaced sternal fractures.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.100-108
• /
• 2006

Time-resolved current and voltage measurements for an inductive automotive spark system were made. Also presented are measurements of the total energy delivered to the spark gap. The measurements were made in air for a range of pressures from 1-18atm, at ambient temperatures. The measured voltage and current characteristics were found to be a function of many ignition parameters; some of these include: spark gap distance, internal resistance of the spark plug and high tension wire, and pressure. The voltages presented were measured either at the top of the spark plug or at the spark gap. The measurements were made at different time resolutions to more accurately resolve the voltage and current behavior throughout the discharge process. This was necessary because the breakdown event occurs on a time scale much shorter than the arc and glow phases. The breakdown, are, and glow voltages were found to be functions of spark plug resistance, gas density, and spark plug gap as expected from the literature. Spark duration was found to decrease as either pressure or gap was increased. The transition from the arc to glow phase is usually distinguished by a sudden rise in the voltage across the gap. At pressures above about 7atm this transition was not observed suggesting that a glow phase was not present. Energy delivered to the gap increased with increasing pressure. The effective resistance of the spark gap during discharge was about twice as large for the glow phase as the arc phase.

• 문화기술의 융합
• /
• 제6권2호
• /
• pp.217-222
• /
• 2020

디지털 경제에서 저작권 논의는 디지털 저작물의 이용환경 변화와 디지털 기술들의 빠른 발전을 반영해야 한다. 이용자 제작 콘텐츠와 기여활동에 있어서 이용자 저작물 권리의 보장, 양도, 이용에 대한 논의가 필요하다. 디지털 아카이브의 경우 이용허락 범위나 인용 가이드를 명시하는 것이 요청된다. 디지털 복제의 규제에 치우치지 않고 표현의 자유를 늘리고 변형적 가치를 고려하는 것이 필요하다. 디지털 제조에서 사적이용과 공적이용, 공유와 산업간의 긴장이 커질 것이므로 정책적 논의가 진행되어야 한다. 저작자의 권리보호 못지않게 저작물의 공정이용의 범위를 확장하는 방향으로 저작권 해석이 제안될 필요가 있다. 저작물의 공정이용 확대와 구체적인 규정 제시가 창작과 유통을 활성화하고 혁신을 생산적으로 사용하는 데 기여할 것이다.

• Bulletin of the Korean Chemical Society
• /
• 제32권1호
• /
• pp.59-64
• /
• 2011

Degree of unsaturation in fatty acid molecules plays an important role in the formation of vesicles. Vesicle formation from C18 fatty acids with different amount of double bonds such as oleic acid, linoleic acid and linolenic acid with the incorporation of 1,2-dipalmitoyl-sn-glycerol-3-phosphoethanolamine-N-[methoxy(polyethylene glycol)-2000] (DPPE-PEG2000) have been examined by TEM. Critical vesicular concentrations (CVC) of the vesicle suspension are determined by turbidity and surface tension methods. The CVC of fatty acids increases when the amount of unsaturation in the alkyl chain increases. On the other hand, stability of vesicle suspension has been examined by using particle size and zeta potential at $30^{\circ}C$. There was a dramatic decrease in particle size measurement from mono-unsaturation to tri-unsaturation which could be due to the effect of fluidity in the membrane bilayer caused by different degree of unsaturation. The values of zeta potential for vesicles that were formed without the incorporation of DPPE-PEG2000 were in the range of -70 mV to -100 mV. It has been observed that the incorporation of DPPEPEG2000 to the vesicle reduces the magnitude of zeta potential. However, this phenomenon does not obviously seen in fatty acid vesicles formed by linoleate-linoleic acid and linolenate-linolenic acid. We therefore conclude that the addition of DPPE-PEG2000 does not effectively improve the stability of the linoleate-linoleic acid and linolenatelinolenic acid vesicle at pH 9.0 after the evaluation of their particle size and zeta potential over a period of 30 days. Although the vesicles formed were not stable for more than 10 days, they have displayed the potential in encapsulating the active ingredients such as vitamin E and calcein. The results show that the loading efficiencies of vitamin E are of encouraging value.

• Geomechanics and Engineering
• /
• 제10권6호
• /
• pp.757-774
• /
• 2016

Soils are usually weak in tension therefore different materials such as geosynthetics are used to address this inadequacy. Worldwide annual consumption of geosynthetics is close to $1000million\;m^2$, and the value of these materials is probably close to US$1500 million. Since the total cost of the construction is at least four or five times the cost of the geosynthetic itself, the impact of these materials on civil engineering construction is very large indeed. Nevertheless, there are several significant problems associated with geosynthetics, such as creep, low modulus of elasticity, and susceptibility to aggressive environment. Carbon fiber reinforced polymer (CFRP) was introduced over two decades ago in the field of structural engineering that can also be used in geotechnical engineering. CFRP has all the benefits associated with geosynthetics and it boasts higher strength, higher modulus, no significant creep and reliability in aggressive environments. In this paper, the performance of a CFRP reinforced retaining wall is investigated using the finite element method. Since the characterization of behavior of soils and interfaces are vital for reliable prediction from the numerical model, soil and interface properties are obtained from comprehensive laboratory tests. Based on the laboratory results for CFRP, backfill soil, and interface data, the finite element model is used to study the behavior of a CFRP reinforced wall. The finite element model was verified based on the results of filed measurements for a reference wall. Then the reference wall simulated by CFRP reinforcements and the results. The results of this investigations showed that the safety factor of CFRP reinforced wall is more and its deformations is less than those for a retaining wall reinforced with ordinary geosynthetics while their construction costs are in similar range.

• 대한기계학회논문집A
• /
• 제34권11호
• /
• pp.1741-1747
• /
• 2010

본 연구에서는 원격 조정 매니퓰레이터에 적용할 수 있는 보급형 서비스 로봇 암을 개발하였다. 생체 모방학을 활용하여 새로운 형태의 로봇 손에 대한 개념을 도출하였다. 손가락과 손목은 인체 팔의 근골격에 분석을 통하여 상박에 설치된 와이어와 액추에이터에 의하여 구동된다. DC 모터에 의해 구동되는 스크류-너트 매커니즘을 통하여 구동 케이블에 높은 장력을 발생시킨다. 파지력의 쉬운 제어를 위하여 스크류-너트 메커니즘에 조합 스프링을 적용하였다. 첫 번째 설계에서 손가락 제어 문제, 손가락과 손목 운동의 간섭 문제가 발견되었다. 트리즈의 모순 분석을 통하여 이러한 문제에 대한 해결안을 도출하였다. 두 번째 설계에 대하여 다양한 형태와 무게의 물체에 관하여 파지와 동작 테스트를 시행하였다.

• 한국토양비료학회지
• /
• 제49권3호
• /
• pp.235-241
• /
• 2016

The soil does not only serve as a medium for plant growth but also for engineering construction purposes. It is very weak in tension, very strong in compression and fails only by shearing. The behaviour of the soil under any form of loading and the interactions of the earth materials during and after any engineering construction work has a major influence on the success, economy and the safety of the work. Soils and their management have therefore become a broad social concern. A limitless variety of soil materials are encountered in both agronomy and engineering problems, varying from hard, dense, large pieces of rock through gravel, sand, silt and clay to organic deposits of soft compressible peat. All these materials may occur over a range of physical properties, such as water contents, texture, bulk density and strength of soils. Therefore, to deal properly with soils and soil materials in any case requires knowledge and understanding of these physical properties. The desired value of bulk density varies with the degree of stability required in construction. Bulk density is also used as an indicator of problems of root penetration,soil aeration and also water infiltration. This property is also used in foundation engineering problems. While not conforming to standard test procedures, this work attempts to add to the basic information on such important soil parameters as water content, bulk density.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.376-385
• /
• 1987

본 연구에서는 평면응력 파괴인성치의 거동에 관한 일련의 연구로서 위와 같 은 점을 고려하여 얇은 두께의 시험편을 이용하여 z의 변화에 대한 평면응력 파괴인성 치와 J저항곡선을 실험적으로 고찰하였으며 크랙성장을 고려한 J적분식도 검토하였다. 크랙길이는 하중제거 컴플라이언스법에 의하여 구하였고, ASTM E813의 방법으로J= .sigma.$_{f}$ .DELTA.(2ａ)인 크랙둔화선과 J저항곡선의 교점에서 구한 J적분값을 J$_{c}$로 정 의하였다. 또한, 재료를 변형경화재료로 가정하여 HRR응력변형율장의 특성을 이용 하여 J적분값을 구한 후 실험치와 상호 비교 검토하였다.이때 입력자료는 실험치의 그것과 동일하게 하였다. 동시에 z의 변화에 대한 T의 변화도 함께 고찰하였다.다.