• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.644-649
• /
• 1993

Practical structures are subject not only to tension but also to shear and torsional loading. In this study, the mode 1 and 2 stress intensity factors of specimens were calculated by using elastic finite element mothod. The stress fields at the crack tip subjected to mixed-mode loading were also studied by usingf eleatic finite element method and were compared with theoretical results. The three-point-bending, four-point-bending, and mixed-mode-loading experiment were carried out. And, crack propagation rate da/dN and crack growth direction were examined. Also, the elastic finite element method was applied to calculate the stress intensity factors of branch crack tip and we relate the stress intenity factor range of branch crack tip(the result of FEM) to crack propagation rate(the experimental result). The .DELTA. -da/dN relation corelated with that of mode 1.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.319-322
• /
• 2003

For the analysis of leveling process by the 3-dimensional elastic-plastic finite element method, a finite element analysis program modeling large deformation of shell has been developed. This program fur analyzing large deformation of sheet during leveling includes spring-back analysis as well as efficient contact treatment between sheet and rolls of leveler. This is verified by the simple leveling experiment with 5 rolls at laboratory. Besides the leveling examples, problems within the category of large strain and rotation, such as 3-dimensional roll-up and gutter occurrence at continuous bending-unbending process are also tested for verification of the program. The residual curvatures of strip predicted by finite element analysis are within 20% error range of the experiment. The formation and direction of anticlastic curvature or gutter during bending-unbending under tension is predicted and this agrees with the experimental results.

• Journal of Welding and Joining
• /
• v.4 no.3
• /
• pp.32-42
• /
• 1986

In this study, the influence of carbon equivalents on friction welds of dissimilar steels was investigated. Four types of carbon steels with 10mm diameter were welded to a high-speed tool steel SKH 9. Main experimental results could be summarized as follows (1) Under constant friction pressure, the friction time increased almost linearly with the increasing burn-off length, while the forge length decreased almost linearly. (2) The maximum hardness in carbon steels increased almost linearly with the increasing carbon equivalent, but was much lower than that in the high speed steel. (3) After quenching and tempering of dissimilar steel friction welds, the hardness in carbon steel weldments became similar as that in the base metal, while the hardness in SKH 9 weld was still higher that of the base metal. (4) Relative movement in the friction phae occurred not at the interface of the weldments, but in the high speed steed steel near the interface. (5) For considered material combinations and welding parameters, most of fractures in tension and twisting tests occurred in the base metal. And welds with so high strength could produced in a wide range of welding parameters.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.10
• /
• pp.1451-1457
• /
• 2002

When an aqueous liquid such as water having high electric conductivity and high surface tension is discharged from a nozzle under a strong DC electric field, fine drops ranging from 30 to 450 microns can be obtained only through the spindle mode. In the present study, effects of the electric conductivity and the surface wettability of nozzle materials on formation of drops with this mode were investigated. For that, three nozzles with the same size but with different materials were prepared and tested; a stainless steel needle, and a plain and a metal (gold)-coated (except for the tip portion) silica needles. Uniform drops were obtained with the gold-coated silica nozzle over the wider range of the DC voltage input. That is, formation of the liquid cone and detachment of the liquid spindle (ligament) can be more stabilized and frequent with the needles having high electric conductivity but with low surface wettability at their tips.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.290-295
• /
• 2004

Mircolens and microlens V-groove are realized using a novel fabrication technology based on the exposure of a resist, usually PMMA, to deep X-rays and subsequent thermal treatment and inclined deep X-ray lithography, respectively. The fabrication technology is very simple and produces microlenses and microlens V-groove with good surface roughness of several nm. The molecular weight and glass transition temperature of PMMA is reduced when it is irradiated with deep X-rays. The microlenses were produced through the effects of volume change, surface tension, and reflow during thermal treatment of irradiated PMMA. Microlenses were produced with diameters ranging from 30 to $1500\mu\textrm{m}$. The surface X-ray mask is also fabricated to realize microlens arrays on PMMA sheet with a large area. The size of the micro V-groove is fabricated in the range of 12~$60\mu\textrm{m}$.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.284-284
• /
• 2006

Electrospray deposited films of poly(vinylidene fluoride) were prepared with various conditions. A model has been developed, which provides the state of the electrosprayed droplet at impact. With a combination of the experimental films and the model calculations, it can be shown that growth rate, the increase of the sprayed solution on the substrate per second, defines the film morphology in electrospray deposition. Growth rate indicates which factors play the main role in the film formation process. The most important factors are liquid flow, surface tension and shear rate. The model can calculate the shear rate and it is shown that PVDF, and most likely polymers in general, has a large range of growth rates, where the morphology only depends on the shear rate of the depositing droplet. This method can also be used to describe electrospray deposition of other compounds.

• Computers and Concrete
• /
• v.8 no.1
• /
• pp.111-123
• /
• 2011

Severe element distortion problem is observed in finite element mesh while performing numerical simulations of high velocity steel projectiles penetration/perforation of concrete targets using finite element method (FEM). This problem of element distortion in Lagrangian formulation of FEM can be resolved by using element erosion methodology. Element erosion approach is applied in the finite element program by defining failure parameters as a condition for element elimination. In this study strain parameters for both compression and tension at failure are used as failure criteria. Since no direct method exists to determine these values, a calibration approach is used to establish suitable failure strain values while performing numerical simulations of ogive-nose steel projectile penetration/perforation into concrete target. A range of erosion parameters is suggested and adopted in concrete penetration/perforation tests to validate the suggested values. Good agreement between the numerical and field data is observed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.501-504
• /
• 2006

Recently, the Ceramic Bricks are getting increased due to demolishing aged buildings. But, disposal of the waste ceramic bricks has been relied on just burying into the ground. Regardless they can be used with recycled thick aggregate. Therefore the range of this study includes the experiment of slump test, compression, strength test and stress-strain analysis to the concrete the recycled thick aggregate with made by ceramic bricks. The reducing method of fine aggregate will be reviewed stand on analysis of this experimental result.

• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.398-401
• /
• 2000

The effect of volatile components on cell growth and polysaccharide production in suspension cultures of Aloe saponaria was investigated using an intelligent on-line gas control system which enabled to control the concentrations of oxygen, carbon dioxide and ethylene simultaneously. Aloe production was enhanced in the presence of exogenous ethylene in the concentration range of 5ppm and 15ppm. Maintaining high tension of carbon dioxide (5% v/v) was found to enhance polysaccharide production significantly.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.2
• /
• pp.382-390
• /
• 1995

Failure of connecting rod in automotive engine may cause catastrophic situation. The corner radius at small end has an effect on stress raising. To investigate the stress distribution in connecting rod during operation, the finite element analysis was used by giving possible maximum tension and compression. Excessive sizing after forging connecting rod may result in the tensile residual stress which lower the fatigue life and cause premature failures. It was shown that when the sizing amount is too large, the location of high tensile residual stress coincide with that of high stress amplitude during operation through the elastic-plastic finite element analysis. The endurance limit moves down due to the surface finish and decarburization, which combines with the movement of resultant stress points to dangerous range. It was concluded that the precise control of sizing and enough corner radius are necessary to a reliability of connecting rod.