• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.11
• /
• pp.2287-2296
• /
• 2002

Most cracks in the structure occur under mixed mode loading and those fatigue crack propagation behavior heavily depends on the stress ratio. So, it is necessary to study the fatigue behavior under mixed mode loading as the stress ratio changes. In this paper, the fatigue crack propagation behavior was respectively investigated at stress ratio 0.1, 0.3, 0.5, 0.7 and we changed the loading application angle into 0$^{\circ}$, 30$^{\circ}$, 60$^{\circ}$ to apply various loading mode. The mode I and II stress intensity factor of CTS specimen used in this study was calculated by the displacement extrapolation method using FEM (ABAQUS). Using both the experiment and FEM analysis, we have concluded the relationship between crack propagation rate and stress intensity factor range at each loading mode due to the variation of stress ratio. Also, when the crack propagated under given stress ratio and loading mode condition, we have concluded the dominant factors of the crack propagation rate at each case.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.4
• /
• pp.80-88
• /
• 1997

An experimental investigation of the fatigue through crack growth behavior under simple stepped variable loading condition has been performed using Al7075-T651. Experiments were carried out by using cantilever bending type specimens, with chevron notches on a small electro-magnetic test machine. Tensile overloads have a retarding effect on the fatigue crack growth rates, therefore tensile overloads were used for the beneficial effect on the fatigue life. While in most cases compressive overloads have only a vanishing effect on crack growth rates, some experiments with single edge crack tension specimens reveal a marked growth retardation. The stress ratios used in this investigations varies from R=0.32 to 0.81, from R=0.04 to 0.76, from R=-0.15 to 0.73, and from R=-0.33 to 0.68 and the peak load for each case was not varied. The crack growth and crack closure were measured by Kikukawa's compliance method with a strain gauge mounted on the backside of each specimens. The results obtained are as follows. When the stepped variable load was applied, the smaller the stress ration was, the larger the delayed retardation of the crack growth rate was. The fatigue crack growh rate data obtained for through cracks were plotted well against the effective stress intensity factor range from 4.0 to 20.0MP{a^{SQRT}m}. It was found that the effective stress intensity factor range ratio was related well to the opening stress intensity factor, the maximum stress intensity factor, and crack length.

• Journal of the Korean Applied Science and Technology
• /
• v.17 no.3
• /
• pp.149-157
• /
• 2000

The synthesis of N-methyl glucamine was performed in two step reaction. The first step involves the amination between methylamine and glucose in methane. The N-methyl glucamine was obtained by the reduction of using Ni catalyst under the high pressure. The second step was glucamide anionic derivatives synthesis from N-methyl glucamine, maleic anhydride, lauryl alcohol and laurylamine by Schotten Banmann reaction respectively. Their molecular structures of N-methyl glucamine and glucamide (EG-MAS and AC-MAS) were investigated by IR and $^{1}H-NMR$. Basic physical properties and biodegradability of there glucamide anionic surfactant was investigated. The range of cmc values determined by measurements of surface tention was $10^{-5}{\sim}10^{-4}mol/l$ and the surface tension of the aqueous solution revealed in the range $28{\sim}30$ dyne/cm and their biodegradability was very good in the pH $5{\sim}10$.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.349-354
• /
• 2001

The split Hopkinson pressure bar has been used for a high strain rate impact test. Also it has been developed and modified for compression, shear, tension, elevated temperature and subzero tests. In this paper, SHPB compression tests have been performed with pure titanium at elevated temperatures. The range of temperature is from room temperature to $1000^{\circ}C$ with interval of $200^{\circ}C$. To raise temperature of the specimen, a radiant heater which is composed of a pair of ellipsoidal cavities and halogen lamps is developed at high temperature SHPB test. There are some difficulties in a high temperature test such as temperature gradient, lubrication and prevention of oxidation of specimen. The temperature gradient of specimen is affected by the variation of temperature. Barreling occurred at not properly lubricated specimen. Stress-strain relations of pure titanium have been obtained in the range of strain rate at $1900/sec{\sim}2000/sec$ and temperature at $25^{\circ}C{\sim}1000^{\circ}C$.

• The Journal of Korean Physical Therapy
• /
• v.29 no.6
• /
• pp.307-315
• /
• 2017

Purpose: The purpose of this study was to investigate the effects of kinesio taping on lumbar flexibility onto erector spinae and sacroiliac joint. Methods: Sixty healthy adults (male=36, female=24) participated in this study and were randomly assigned to the experimental group that received kinesio taping onto erector spinae and sacroiliac joint (n=30) or the control group that received X-letter placebo taping onto them (n=30). Lumbar flexibility (flexion, extension, lateral flexion, and rotation) was measured using back range-of-motion instrument (BROM) II before and after taping. Results: In the change of lumbar flexibility after taping in the experimental group, there were statistically significant difference in flexion, lateral flexion, and rotation (p<0.05), but there was no significant difference in extension. There was no significant difference in the change of lumbar flexibility after taping in the control group. Conclusion: In conclusion, kinesio taping onto erector spinae and sacroiliac joint improved the joint function. Kinesio taping may reduce the muscle tension and facilitate the circulation of tissue fluid. In light of these results, it is thought that the application of kinesio taping had influence on an increase in lumbar flexibility. Therefore, kinesio taping will be able to be used as the method of the prevention of pain and the treatment in the lumbar region.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.193-197
• /
• 2005

Influences of microstructure on high-cycle fatigue (HCF) limit of high carbon $(>0.7wt.\;\%)$ steel filaments used for tires have been investigated. A series of the fatigue tests was carried out depending on carbon content by using Hunter-type tester at a frequency of 60 Hz at a tension/compression stress of 900 to 1500 MPa. Microstructural changes of the filaments were identified in the lateral direction by using transmission electron microscopy (TEM). It was found that the mechanical properties, such as fatigue limit and tensile strength, were improved with increasing carbon content, which was mainly attributed to decreased lamellar spacing and cementite thickness. However, the fatigue ratio, which is defined as the ratio of the fatigue limit to the tensile strength, was reduced in a higher carbon range of 0.8 to $0.9\;wt.\%$, while the fatigue ratio was nearly constant in a lower carbon range of 0.7 to $0.8\;wt.\%$. Overall mechanical properties of the filaments, depending on carbon content, have been discussed in terms of the microstructural parameter change of lamellar spacing and cementite thickness. In addition, the variation of cementite morphology on the fatigue crack propagation of high carbon $(0.9wt.\;\%)$ filaments will be discussed.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.4
• /
• pp.212-219
• /
• 2001

The fatigue test was carried out to evaluate the fatigue characteristics of fire resistance steel for frame structure and heat affected zone (HAZ) by the one side Gas Metal Arc Welding (GMAW). In this paper, the fatigue crack growth behavior was investigated with the compact tension specimen of base metal and the HAZ according to chemical composition and rolling end temperature, respectively. And the acoustic emission signals obtained from the fatigue test were analyzed by the time-frequency analysis method as a nondestructive evaluation. Main results obtained are summarized as follows; The hardness was appeared softening phenomenon that weld metal and HAZ are lower than that of base metal. Fatigue life of welded specimen was longer than that of base metal. m was 3~4.5 in base metal and 3.8~5.8 in HAZ. The main frequency range of acoustic emission signal analyzed from time-frequency method is different with the range by noise and crack. Also, it could be classified that it was also generated by fracture mechanics of dimple, inclusion etc.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.174-181
• /
• 2005

In order to investigate the behavior of fatigue crack growth of SiC-particulate- reinforced Al-Si alloy composites, fatigue tests using single edge notched tension(SENT) specimens were performed. Composite materials were manufactured by using both permanent die casting and extrusion processes with different volume fractions of $10\%\;and\;20\%$. $SiC_p-reinfurced$ Al-Si composites showed the increased levels of threshold stress intensity factor range, ${\Delta}K_{th}$, for the increased volume fractions of SiC particles, which implies the increased fatigue crack growth resistance at the threshold or low ${\Delta}K$ levels, compared to the unreinforced Al-Si alloy. In the Paris region, however, the composites showed the increased rate of crack growth resulting in the unfavorable effects on the fatigue crack growth resistance. Critical stress intensity factor range at unstable crack growth leading to final fracture decreased as the volume fraction of SiC particle increased, because of the reduced fracture toughness of the composites. Extruded materials showed higher threshold and critical values than the cast materials.

• Computers and Concrete
• /
• v.23 no.6
• /
• pp.377-398
• /
• 2019

Behavior of RC beam-column joint is very complex as the composite material behaves differently in elastic and inelastic range. The approaches generally used for predicting joint shear strength are either based on theoretical, strut-and-tie or empirical methods. These approaches are incapable of predicting the accurate response of the joint for entire range of loading. In the present study a new generalized RC beam-column joint shear strength model based on hybrid approach i.e. combined strut-and-tie and empirical approach has been proposed. The contribution of governing parameters affecting the joint shear strength under compression has been derived from compressive strut approach whereas; the governing parameters active under tension has been extracted from empirical approach. The proposed model is applicable for various conditions such as, joints reinforced either with or without shear reinforcement, joints with wide beam or wide column, joints with transverse beams and slab, joints reinforced with X-bars, different anchorage of beam bar, and column subjected to various axial loading conditions. The joint shear strength prediction of the proposed model has been compared with 435 experimental results and with eleven popular models from literature. In comparison to other eleven models the prediction of the proposed model is found closest to the experimental results. Moreover, from statistical analysis of the results, the proposed model has the least coefficient of variation. The proposed model is simple in application and can be effectively used by designers.

• Food Science and Preservation
• /
• v.30 no.4
• /
• pp.589-601
• /
• 2023

Malaysian honey is rich in nutrients and bioactive compounds, which can be a healthy alternative to refined sugar in food production. However, liquid honey's viscous and sticky nature makes it unpreferable in industrial handling. This study, an atomization system coupled with vacuum drying to produce honey powders to overcome the problem. Three types of Malaysian honey, namely Acacia, Gelam, and Tualang, were encapsulated in Ca-alginate gel beads using the atomization system. The density viscosity, and surface tension of the honey-alginate solutions were measured, and the concentration of honey and alginate influenced the physical properties of the solutions. Honey-encapsulated gel beads in the size range of 2.16-2.92 mm were produced using the atomization system with the air-liquid mass flow rate ratios of 0.22-0.31, Weber number (We) of 112-545, and Ohnersorges number (Oh) of 0.35-10.46. Gel bead diameter can be predicted using a simple mathematical model. After vacuum drying, the honey gel powder produced was in the size range of 1.50-1.79 mm. Results showed that honey gel powders with good encapsulation efficiency and high honey loading could be produced using the atomization system and vacuum drying.