• 한국강구조학회 논문집
• /
• 제15권2호
• /
• pp.137-145
• /
• 2003

본 연구에서는 국산 PS 강봉의 직경, 반복최소응력 및 반복최대응력 등을 실험변수로 하여 직접 인장 피로실험을 수행하였다. 정적 인장실험 결과, 국산 PS 강봉의 응력 - 변형률 곡선과 극한강도 등을 얻었다. 또한, 피로실험에서의 특징적인 실험결과는 PS 강봉의 직경은 피로 수명에 중요한 인자가 아니며, 반복 최소응력의 크기는 국산 PS 강봉의 피로수명에 매우 큰 영향을 미치는 것으로 나타났다. 이러한 피로실험결과를 통계 분석하여 PS 강봉의 응력 범위 및 반복 최소응력 등을 변수로 하는 피로강도 예측식을 제안하였다. 피로실험 중, 시편중앙에 설치한 Extensometer를 이용하여, 변형률의 변화를 측정하였으며, 측정된 변형률 변화현상에서 탄성계수의 변화현상을 구하였다. 변형률 증가현상은 3단계의 형태 즉, 초기에 급격한 증가 후 서서히 증가하며 파괴 직전에 급격하게 증가하는 형태로 나타났다. 탄성계수의 변화현상은 변형률 변화현상과 유사하게 감소하는 것으로 나타났으며 응력수준은 탄성계수 변화에 큰 영향을 주지 않는 것으로 나타났다.

• 한국지반환경공학회 논문집
• /
• 제13권11호
• /
• pp.19-26
• /
• 2012

본 논문에서는 지반 내 보강재를 삽입하여 원지반 전체의 전단강도와 활동저항력을 증가시켜주는 네일링에 프리스트레스를 가할 수 있는 PC강연선을 결합한 앵커형 네일에 대한 연구를 수행하였다. 앵커형 네일의 거동특성을 확인하기 위하여 무보강, 네일링, 앵커형 네일 각각에 대하여 실내모형실험과 수치해석을 수행하여 하중-변위, 벽체변위 등을 분석하였다. 실내모형실험결과 프리텐션을 가한 앵커형 네일의 경우 일반네일과 비교할 때 하중증가에 따른 수평변위량이 크게 감소되는 것이 확인되었으며, 특히 벽체상부의 변위 억제력이 커짐을 알 수 있었다. 이를 확인하기 위한 수치해석결과도 실내모형실험과 유사한 해석결과를 나타내었다.

• 대한기계학회논문집A
• /
• 제30권11호
• /
• pp.1494-1501
• /
• 2006

Mechanical and physical properties of a copper alloy for a liquid rocket engine(LRE) combustion chamber liner application were tested at various temperatures. All test specimens were heat treated with the condition they might experience during actual fabrication process of the LRE combustion chamber. Physical properties measured include thermal conductivity, specific heat and thermal expansion data. Uniaxial tension tests were preformed to get mechanical properties at several temperatures ranging from room temperature to 600$^{\circ}C$. The result demonstrated that yield stress and ultimate tensile stress of the copper alloy decreases considerably and strain hardening increases as the result of the heat treatment. Since the LRE combustion chamber operates at higher temperature over 400$^{\circ}C$, the copper alloy can exhibit time-dependent behavior. Strain rate, creep and stress relaxation tests were performed to check the time-dependent behavior of the copper alloy. Strain rate tests revealed that strain rate effect is negligible up to 400$^{\circ}C$ while stress-strain curve is changed at 500$^{\circ}C$ as the strain rate is changed. Creep tests were conducted at 250$^{\circ}C$ and 500$^{\circ}C$ and the secondary creep rate was found to be very small at both temperatures implying that creep effect is negligible for the combustion chamber liner because its operating time is quite short.

• 한국공간구조학회논문집
• /
• 제11권3호
• /
• pp.115-123
• /
• 2011

ETFE막재는 PTFE막재에 비해 상대적으로 두께가 매우 얇고 유연하기 때문에 다양한 온도환경에 따른 막재의 재료특성을 알아볼 필요가 있다. 본 논문에서는 ETFE 막재에 대해 다양한 온도하에서의 재료특성 실험을 수행하였다. 첫째로, -20$^{\circ}C$, 0$^{\circ}C$, +20$^{\circ}C$, +40$^{\circ}C$ 하에서 각각 5 시험편을 이용하여 인장실험을 수행하였으며, 각 온도하에서의 항복응력, 인장강도, 영계수를 도출하였다. 두 번째는, 25$^{\circ}C$, 40$^{\circ}C$, 60$^{\circ}C$ 하에서 각각 3MP, 6MP, 9MP의 하중을 가하여 각 온도에 따른 크리프 변형도를 알아보았다. 마지막으로, -15$^{\circ}C$, 0$^{\circ}C$, 20$^{\circ}C$ 하에서의 인열강도 시험을 수행하였다. 시험결과분석에 따르면, ETFE막재의 전제적인 거동은 크게 변하지 않았으나, 재료특생은 온도의 영향을 받고 있음을 알 수 있었다.

• 한국해양공학회지
• /
• 제26권4호
• /
• pp.77-85
• /
• 2012

A study was performed on the design of a mooring line to maintain the position of a floating WEC (wave energy conversion) system. The procedure to design a mooring line is set up and the safety of the designed mooring system is evaluated using commercial software, Orcaflex. The characteristics curve for one line is analyzed to determine the properties and pretension of a mooring line. While considering the ocean environmental condition and importance of a floating WEC system, a multi-line layout is determined. A 4-point mooring system with 4 lines shows the instability in the yaw motion of the floating WEC system under a designed ocean environmental condition. The redesigned 4-point mooring system with 8 lines is found to be safe on the condition of a harsh ocean environment. The floating WEC system with the redesigned mooring system also shows stable motion in surge and pitch under operating conditions. From a parametric study on the mooring line length, the extreme value of the mooring line tension is found to be very sensitive to the pretension and length of mooring line. The results of this study can contribute to the establishment of a design procedure for mooring lines.

• 한국인쇄학회지
• /
• 제25권1호
• /
• pp.43-52
• /
• 2007

Offset printing is one of the well known printing technique of lithographic process and consists of image area and 'non-image area on a flat image carrier. The surface tension of dampening water can be controlled by adding IPA after mixing of raw water and etching solution. The etching solution contains a surfactant for reducing surface energy, a clean agent for non-imaging area, wetting agent for protecting non-imaging area from oil components like ink and also an emulsifying agent for controlling emulsification. In this study, the present situation of dampening water maintenance has examined by collecting dampening water using at domestic companies. The pH related to dampening water, conductivity, contact angle, emulsification curve are measured to define the current situation of dampening water control of each companies and to analyze the relationship among measured properties. In the study most of companies among 16 printing companies tested controlling dampening water through pH value. However, the quality of printing has varied depending upon conductivity, contact angle, IPA content, and emulsification value. The control of dampening water should be carry at the state of the standard when adding proper ratio of etching solution. It would be more effective when pH or conductivity control carries out in parallel with controlling dampening water. Therefore the concept that pH5.5 is correct is based concept. Based on these initial tests it is defined that the standardization of dampening water control is required.

• Steel and Composite Structures
• /
• 제18권6호
• /
• pp.1369-1389
• /
• 2015

In order to investigate the behaviour of lying multi-stud connectors in cable-pylon anchorage zone, twenty-four push-out tests are carried out with different stud numbers and diameters. The effect of concrete block width and tensile force on shear strength is investigated using the developed and verified finite element model. The results show that the shear strength of the lying multi-stud connectors is reduced in comparison with the lying single-stud connector. The reduction increases with the increasing of the number of studs in the vertical direction. The influence of the stud number on the strength reduction of the lying multi-stud connectors is decreased under combined shear and tension loads compared with under pure shear. Yet, due to multi-stud effect, they still can't be ignored. The concrete block width has a non-negligible effect on the shear strength of the lying multi-stud connectors and therefore should be chosen properly when designing push-out specimens. No obvious difference is observed between the strength reductions of the studs with 22 mm and 25 mm diameters. The shear strengths obtained from the tests are compared with those predicted by AASHTO LRFD and Eurocode 4. Eurocode 4 generally gives conservative predictions of the shear strength, while AASHTO LRFD overestimates the shear strength. In addition, the lying multi-stud connectors with the diameters of 22 m and 25 mm both exhibit adequate ductility according to Eurocode 4. An expression of load-slip curve is proposed for the lying multi-stud connectors and shows good agreement with the test results.

• The Korean Journal of Physiology and Pharmacology
• /
• 제19권6호
• /
• pp.533-542
• /
• 2015

Little human tissue data are available for slow waves and migrating motor complexes, which are the main components of small bowel motility. We investigated the electrophysiological and mechanical characteristics of human ileal motility, in vitro. Ileum was obtained from patients undergoing bowel resection. Electrophysiological microelectrode recordings for membrane potential changes and mechanical tension recordings for contraction from smooth muscle strips and ileal segments were performed. Drugs affecting the enteric nervous system were applied to measure the changes in activity. Slow waves were detected with a frequency of 9~10/min. There were no cross-sectional differences in resting membrane potential (RMP), amplitude or frequency between outer and inner circular muscle (CM), suggesting that electrical activities could be effectively transmitted from outer to inner CM. The presence of the interstitial cell of Cajal (ICC) at the linia septa was verified by immunohistochemistry. Contractions of strips and segments occurred at a frequency of 3~4/min and 1~2/min, respectively. The frequency, amplitude and area under the curve were similar between CM and LM. In segments, contractions of CM were associated with LM, but propagation varied with antegrade and retrograde directions. Atropine, $N^W$-oxide-L-arginine, and sodium nitroprusside exhibited different effects on RMP and contractions. There were no cross-sectional differences with regard to the characteristics of slow waves in CM. The frequency of contractions in smooth muscle strips and ileal segments was lower than slow waves. The directions of propagation were diverse, indicating both mixing and transport functions of the ileum.

• Journal of the Korean Wood Science and Technology
• /
• 제45권6호
• /
• pp.728-736
• /
• 2017

In this study, the bending behavior of cross-laminated timber (CLT) connected by nails were investigated. Especially, the load-carrying capacity of the nail-jointed CLT under out-of-plane bending was predicted by the lateral resistance of the used nails. Three-layer nail-jointed CLT specimens and a nail connection were manufactured by 30 mm (thickness) ${\times}$ 100 mm (width) domestic species (Pinus koraiensis) laminas and Ø$3.15{\times}82mm$ nails using a nail-gun. Shear test for evaluating the nail lateral resistance and bending test for evaluating the load-carrying capacity of the nail-jointed CLT under out-of-plane bending were carried out. As a result, two lateral resistance of the used nail, the 5% fastener offset value and the maximum value, were 913 N and 1,534 N, respectively. The predicted load-carrying capacity of the nail-jointed CLT by the 5% offset nail lateral resistance was similar to the yield points on the actual load-displacement curve of the nail-jointed CLT specimens. Meanwhile, the nail-jointed CLT specimens were not failed until the tension failure of the bottom laminas occurred beyond the maximum lateral resistance of the nails. Thus, the measured maximum load carrying capacities of the nail-jointed CLT specimens, approximately 12,865 N, were higher than the predicted values, 7,986 N, by the maximum nail lateral resistance. This indicates that the predicted load-carrying capacity can be used for designing a structural unit such as floor, wall and roof able to support vertical loads in a viewpoint of predicting the actual capacities more safely.

• 콘크리트학회지
• /
• 제7권4호
• /
• pp.149-156
• /
• 1995

경량기포콘크리트(ALC : Autoclaved Lightweight Concrete)의 내구성을 개선하기 위하여 투숩 및 투수, 편면동결융해 특성과 탄산화 특성을 실험하였다. 국산 ALC전용마감재는 방수용 도장재에 가까운 투습 및 투수성질을 갖고 있어 특성의 개선이 요구된다. 편면동결융해시험에서 마감재의 투습도에 따른 열화위치는 투습도가 클수록 외측에서 발생하였으나 투수에 의한 외부의 박리열화는 관찰되자 않았다. 탄산화는 수분의 함량이 작을수록 빠르게 진행되었으며 탄산화가 진행됨에 따라 기공량은 감소하였다. 탄산화가 완전히 진행되면 부피의 팽창으로 균열이 발생하였다.