• 한국주조공학회지
• /
• 제12권5호
• /
• pp.397-402
• /
• 1992

The effect of the solution & aging treatment on the tensile strength, yield strength, elongation, reduction of area, hardness was studied in the 17-4 PH stainless steel. SEM pictures were also taken in order to examine the fracture surfaces and precipitated particles. X-ray diffraction patterns for the heat treated samples were also observed. Mechanical properties of the heat treated samples were superior to those of as cast samples. Tensile strength, yield strength, hardeness decreased with the increase of aging temperature. On the other hand, elongation and reduction of area increased as the aging temperature increased.

• 한국기계연구소 소보
• /
• 통권20호
• /
• pp.71-78
• /
• 1990

This investigation was undertaken to establish the technologies of grain refinement and modification, and to characterize material properties, essential for high quality aluminum alloy castings. Grain refinement seldom changed DAS and eutectic Si size, but largely decrease grain size. The variations of grain size induced by grain refinement had a great influence on the elongation without changes in the tensile strength or yield strength. The optimum Ti level lies between 0.1% and 0.16% to achieve the best possible mechanical properties. DAS and grain size were little affected, but eutectic Si size was greatly refined by modification. The variation of eutectic Si size had a great effect on the elongation, impact value, fracture toughness and fatigue crack propagation rate without changes in the tensile strength or yield strength. The Sr content of 0.015% is optimum to modification.

• 한국재료학회지
• /
• 제29권4호
• /
• pp.211-220
• /
• 2019

In this study, three kinds of bainitic steel plates are manufactured by varying the chemical compositions and their microstructures are analyzed. Tensile and Charpy impact tests are performed at room and low temperature to investigate the correlation between microstructure and mechanical properties. In addition, heat affected zone (HAZ) specimens are fabricated by a simulation of welding processes, and the HAZ microstructure is analyzed. The base steel that has the lowest carbon equivalent has the highest volume fraction of acicular ferrite and the lowest volume fraction of secondary phases, so the strength is the lowest and the elongation is the highest. The Mo steel has a higher volume fraction of granular bainite and more secondary phases than the base steel, so the strength is high and the elongation is low. The CrNi steel has the highest volume fraction of the secondary phases, so the strength is the highest and elongation is the lowest. The tensile properties of the steels, namely, strength and elongation, have a linear correlation with the volume fraction of secondary phases. The Mo steel has the lowest Charpy impact energy at $-80^{\circ}C$ because of coarse granular bainite. In the Base-HAZ and Mo-HAZ specimens, the hardness increases as the volume fraction of martensite-austenite constituents increases. In the CrNi-HAZ specimen, however, hardness increases as the volume fraction of martensite and bainitic ferrite increases.

• 한국주조공학회지
• /
• 제22권4호
• /
• pp.155-159
• /
• 2002

Magnesium alloys have high strength to weight ratio and are extremely attractive for applications in transport industry. Most of structural magnesium alloys are manufactured by die casting process. The tensile properties of AZ91HP magnesium alloy were investigated after die casting under various die casting conditions. After die casting by using cold chamber machine, the volume porosity of specimens was examined with density method. With the increase of the volume porosity of specimens, both the tensile strength and elongation were significantly decreased, however the 0.2% offset strength was almost independent of the amount of porosity. With the increase of crystal pressure from 500 to 900 bar during die casting, the volume porosity was decreased, which resulted in the increase of the tensile strength. The mould temperature within the range of $150{\sim}250^{\circ}C$ has not influenced the microstructure with the eutectic phase and tensile properties of specimens. The tensile strength was the highest at 90m/sec of gate speed.

• 연구논문집
• /
• 통권29호
• /
• pp.185-194
• /
• 1999

The shape and thickness distribution according to the pressure-time curve were carried out using the FEM and experiment. Also, mechanical properties were investigated. The square cup parts have been formed with pressure-time curve generated by result of analysis. The tensile strength and elongation have been investigated according to applied pressure conditions using the tensile test specimen obtained from the superplastic formed cup. We can use to predict the shape of formed part under the applied pressure using the FEM analysis. In the case of optimum pressure condition, the thickness distribution and mechanical properties were improved. From this study, we can find the important of optimum pressure-time condition. We have investigated about the forming of airplane part and fuel tank for motorcycle. If the applied load used in boundary conditions was appropriate, the simulation result coincides with the formed part. However, it is very difficult to define the pressure condition in complicated shape. Thus, it is need to develop the optimum pressure condition for superplastic forming.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.322-324
• /
• 2007

Nd:YAG laser welding of AZ31B-H24 magnesium alloy was carried out using AZ61 filler wire(Mg-6wt%Al-1wt%Zn). Microstructure and mechanical properties of welded joint were examined by optical microscopy, scanning electronic microscopy(SEM), energy dispersive spectroscopy(EDS), electron probe micro analyzer(EPMA) and victors hardness, tensile test at the room and elevated temperature. Test results indicate that the specimens welded with AZ61 filler wire have better tensile strength, elongation and victors hardness at room temperature than those of welded without filler wire. However tensile strength are similar but elongation are quite different at elevated temperature.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.228-233
• /
• 2004

The characteristics of the probability distribution for mechanical properties, e.g. tensile strength, reduction of area ana elongation, for STS304 stainless steel in elevated temperature were investigated from tensile test performed by constant cross head speea controls with 1mm/min, Recently, in order to clarify the strengthening mechanisms at high temperature, a new scheme to improve high temperature mechanical properties is desired. Therefore, the test ,technique development of high temperature creep behaviors for this material is very important. In this paper, the creep praperties and creep life prediction by Larson-Miller parameter method for STS304 stainless steel to be used for other high temperature components were presented at the elevated temperatures of 600, 650 and $700^{\circ}C$.

• 한국해양공학회지
• /
• 제18권2호
• /
• pp.64-69
• /
• 2004

The characteristics of the probability distribution for mechanical properties, e.g. tensile strength, reduction of area, and elongation, for STS304 stainless steel in elevated temperature are investigated. Tensile test is performed by constant crosshead speed controls with 1mm/min. The probability distribution function of measured mechanical properties seems to follow $\alpha$ 3-parameter Weibull, and shows a slight dependence on the temperature. When the temperature is raised, the shape parameter a is increased, but both the scale parameter $\beta$ and location parameter v are decreased.

• 한국의류학회지
• /
• 제22권6호
• /
• pp.609-609
• /
• 1998

This paper surveys the effect of rice straw ash solution to the physical properties of Sappan Wood dyeing fabrics. In the quantitative analysis of rice straw ash solution, the quantities of absorbed ingredients in fabrics were increased by bath pull treatment but the amount of absorption(K/S value) was increased by bath pH4.5 treatment. This is related to the metal ion. Among the metal ion, effect of Fe iou and Al ion were related. In case added extracted dye solution to mordants, the color dye solution became dark and increased reddish. The changes of mechanical properties of fabrics tensile resilience, bending rigidity(B), compressional resilience(RC) were increased. Generally mechanical properties were increased by rice straw ash solution treatment, specially bath pH9 treatment. Rice straw ash solution treatment of dyeing fabrics made the improvement in tensile strength and elongation and in the amount of absorption, dye ability, color fastness, mechanical properties, tensile strength, elongation.

• 한국의류학회지
• /
• 제22권6호
• /
• pp.699-705
• /
• 1998

This paper surveys the effect of rice straw ash solution to the physical properties of Sappan Wood dyeing fabrics. In the quantitative analysis of rice straw ash solution, the quantities of absorbed ingredients in fabrics were increased by bath pull treatment but the amount of absorption(K/S value) was increased by bath pH4.5 treatment. This is related to the metal ion. Among the metal ion, effect of Fe iou and Al ion were related. In case added extracted dye solution to mordants, the color dye solution became dark and increased reddish. The changes of mechanical properties of fabrics tensile resilience, bending rigidity(B), compressional resilience(RC) were increased. Generally mechanical properties were increased by rice straw ash solution treatment, specially bath pH9 treatment. Rice straw ash solution treatment of dyeing fabrics made the improvement in tensile strength and elongation and in the amount of absorption, dye ability, color fastness, mechanical properties, tensile strength, elongation.