• Computers and Concrete
• /
• 제20권4호
• /
• pp.429-437
• /
• 2017

In this study, the effect of the tensile strength and ratio of disc spacing to penetration depth on the efficiency of tunnel boring machine (TBM) is investigated using Particle flow code (PFC) in two dimensions. Models with dimensions of $150{\times}70mm$ made of rocks with four different tensile strength values of 5 MPa, 10 MPa, 15 MPa and 20 MPa were separately analyzed and two "U" shape cutters with width of 10 mm were penetrated into the rock model by velocity rate of 0.1 mm/s. The spacing between cutters was also varied in this study. Failure patterns for 5 different penetration depths of 3 mm, 4 mm, 5 mm, 6 mm, and 7 mm were registered. Totally 100 indentation test were performed to study the optimal tool-rock interaction. An equation relating mechanical rock properties with geometric characteristics for the optimal TBM performance is proposed. The results of numerical simulations show that the effective rock-cutting condition corresponding to the minimum specific energy can be estimated by an optimized disc spacing to penetration depth, which, in fact, is found to be proportional to the rock's tensile strength.

• Design & Manufacturing
• /
• 제14권4호
• /
• pp.46-51
• /
• 2020

The purpose of this study was to analyze the change in tensile strength characteristics of the weld when the welding speed and rotational speed of the tool, which are representative variables of the friction stir welding process. The equipment used in the experiment was Machining Center No. 5. The material used in the experiment is an AA6061-T6 alloy, and a rolled plate with a thickness of 2mm was used. Two experimental variables were selected, the welding speed of the tool and the rotational speed of the tool. The experimental conditions were selected in the range in which a healthy weld could be obtained through a preliminary experiment. The welding speed of the tool was increased to 100mm/min, 200mm/min, and 300mm/min, and the rotational speed of the tool was increased to 1000rpm, 2000rpm, and 3000rpm. As a result of the experiment, the tensile strength increased as the rotational speed of the tool changed at each tool welding speed. In addition, as the welding speed of the tool increased, the tensile strength of the weld was increased. The condition with the highest tensile strength of the weld was found to be a tool feed speed of 300 mm/min and a tool rotation speed of 3000rpm.

• 항공우주시스템공학회지
• /
• 제3권1호
• /
• pp.12-16
• /
• 2009

The laminated sequence and thickness of a composite structure is an important design parameter which affect the strength and impact damage. In this study, it was investigated the residual strength of carbon fiber laminate after impact damage by the experimental investigation. The tensile strength test and compressive strength test were used to find the mechanical properties, previously. Impact test was performed using low-velocity drop-weight test equipment. The impact damages were finally assessed by the compressive strength test. The investigation results revealed the residual strength of the damaged specimens due to the impact damage.

• 한국의류학회지
• /
• 제42권2호
• /
• pp.224-236
• /
• 2018

This study analyzed differences between Jumchi-Hanji papers not dyed and dyed with persimmon juice (50% concentration) in five strength properties (tensile, wet tensile, tearing, bursting, and folding strengths). For the analysis, the undyed and the dyed Jumchi-Hanji papers were made by Jumchichigi during 40 minutes and made with the Dakji of different layer (a layer, two layers) and Choji method (Oebal-teugi, Ssangbal-teugi). Differences between Jumchi-Hanji papers dyed with the different concentration of persimmon juice (20% vs 70%) in the five strengths were also identified. For this examination, Jumchi-Hanji papers were made with two layer Dakji (Oebal-teugi Choji method) and by Jumchichigi during 60 minutes. Jumchi-Hanji papers made in this study were used as test samples. As a result, Jumchi-Hanji papers dyed with persimmon juice had higher tensile strength (CD), wet tensile strength (MD, CD), and bursting strength than those of undyed Jumchi-Hanji papers. However, tearing strengths (MD, CD) of dyed Jumchi-Hanji papers were lower than undyed Jumchi-Hanji papers. Folding strengths (CD) of dyed Jumchi-Hanji papers were low but the folding strengths (MD) of them were high compared to undyed Jumchi-Hanji papers. In addition, the concentration of persimmon juice influenced the five strength properties of Jumchi-Hanji. The tensile, wet tensile, and bursting strengths of Jumchi-Hanji papers dyed with a 70% concentration were higher than those one of Jumchi-Hanji papers dyed with a 30% concentration while the tearing and folding strengths of Jumchi-Hanji papers dyed with a 70% concentration were lower than Jumchi-Hanji papers dyed with a 30% concentration.

• 한국도로학회논문집
• /
• 제16권6호
• /
• pp.19-25
• /
• 2014

PURPOSES : This study was performed to evaluate the possibility of Indirect Tensile Strength (ITS) as a testing method that can predict cracking on pavement. METHODS : Three asphalt binders and one kind of aggregate were used in this study, and all asphalt mixtures were produced using Gyratory Compactor followed asphalt mix design. The ITS test was performed for the mixture which are artificially short-term aged using the oven. The ITS properties were analyzed by air void, compaction temperature, asphalt content, and asphalt binder. RESULTS : The results of this study indicated that (1) the compaction temperature did not show relationship with the ITS test; (2) there was no specific trend between the asphalt content and the ITS test; (3) the ITS could reveal the property of kinds of asphalt binders; (4) the asphalt mixture that were produced at optimum temperature suggested by manufacturer did not exhibit optimum result for all asphalt binder. CONCLUSIONS : The possibility of ITS was confirmed from this study for replacement of the Marshall Stability method. However, it needs to perform in further studies of aggregate and compaction property to suggest a new ITS standard value.

• Journal of Welding and Joining
• /
• 제19권1호
• /
• pp.112-117
• /
• 2001

The factor affecting on the fatigue strength of spot welded specimen have been studied. To analyze and predict crack initiation position and propagation directions on the spot welded area are very important for strength design of the automobile body structure. In fact, there are a various of loads in running automobile but, it is impossible to replay like an actual conditions in the laboratory. So, in this study tensile-shear type and in-plane bending type specimens were used in fatigue test and includes an analysis of fatigue crack initiation position and propagation directions about earth specimens. The results obtained in the present study are summarized as follows: 1. In tensile-shear type fatigue test, the region of fatigue crack initiation position was affected by out-of-plane bending deformation due to bending angle. 2 In in-plane bending type fatigue test, the behavior of fatigue crack initiation position and propagation derections due to angle between upper plate and lower plate was dominated by magnitude of in-plane bending moment.

• 수산해양기술연구
• /
• 제59권2호
• /
• pp.110-116
• /
• 2023

In this study, samples of sea anchor canopy cloth mainly used in Korean jigging fishing vessels were collected and tested for performance evaluation. The canopy cloth of sea anchor is a basic element of form composition that is known to have the greatest influence on anchor performance. In order to evaluate the performance of sea anchor canopy cloth, five types of samples were tested for new metric count, tensile strength, water vapour transmission rate and drying speed according to the national standard (KS), and some correlations were identified. As a result of the test, the new metric count of cloths was 335.5-443.4 denier in warp and 217-447.6 denier in weft, and the minimum tensile strength was 860 N in warp direction and 430 N in weft direction. The apparent number and tensile strength of cloth were proportional, the water vapour transmission rate of the sample was 206.8 g/m²h, and the drying speed was 90-100 min. This study partially confirmed the performance evaluation based on speculation by the standard test method, and further research is needed on the clear relationship between the research results and the performance of the sea anchor.

• Corrosion Science and Technology
• /
• 제17권2호
• /
• pp.81-89
• /
• 2018

In this study, the effect of Nb alloying element on the corrosion fatigue properties of high strength steel is investigated by conducting fatigue experiments under corrosive condition and hydrogen induced condition, potentiodynamic polarization test, tensile test and surface analyses. Nb element is added to enhance the mechanical property of medium carbon steel. This element forms MX-type phases such as carbides and nitrides which are playing an important role in the grain refinement. The grain refinement is one of the effective way to improve mechanical property because both tensile strength and toughness can be improved at the same time. However, MX-type phase precipitates can be a susceptible site to localized corrosion in corrosive environment due to the potential difference between matrix and precipitate. The obtained results showed that Nb-added steel improved corrosion fatigue property by grain refinement. However, it is degraded for hydrogen-induced fatigue property due to Nb, Ti-inclusions acting as a stronger trap.

• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.73-81
• /
• 1997

This study was to find the best adhesive condition comparing mechanical property in case of hot-melt adhesion using glue-gun, ultrasonic welding with adhesion and only ultrasonic welding in order to adhere thermoplastic resin of polyethylene (PE) in which reliable adhesion was resulted in case of ultrasonic welding with same materials of PE. The best welding condition were acquired at welding time 1 second, welding pressure 250kPa for PE-PE where welding time and welding pressure were increased in accordance with the increase of material strength. At the best ultrasonic welding conditions, bonding strength of PE-PE welding was about 21MPa of which material have tensile strength of 24MPa. Through the analysis of microscophic test for ultrasonic welding structure, it was distinguished between well welded structure with higher intermolecule flow and bad welded structure with lower flow, of which result is mostly correspond with the result of tensile strength test.

• 자동차안전학회지
• /
• 제7권3호
• /
• pp.19-24
• /
• 2015

Brake pads are a component of disc brake system of automobile and consist of steel backing plates and friction material facing the disk brake rotor. Due to the repeated sliding forces and torque in vehicle braking, friction performance of brake pads are ensured. Futhermore, the brake pad is one of major tuning components in aftermarket, mechanical characteristics of the brake pad are necessary to evaluate for establishing the certification standards of tuning components. This study had performed the five specimen tests for friction coefficients and wear loss rates according to the SAE test specification. Using the instrumented indentation method, yield strength and tensile strength were measured. Friction coefficients, 0.386 - 0.489, and wear loss rates, 1.0% - 3.7% are obtained. The range of yield strength and tensile strength are 21.4 MPa - 105.3 MPa and 39.5 MPa - 176.4 MPa respectively.