• Biotechnology and Bioprocess Engineering:BBE
• /
• v.10 no.3
• /
• pp.186-191
• /
• 2005

In this study, a microorganism-produced protease was used to improve the quality of fabrics. First, the protease-producing bacteria were isolated from soils, and one of them was selected and identified as Bacillus sp. SJ-121. The optimal medium composition for its growth and protease production was determined to be as follows: glucose 1g/L, soybean meal 0.5g/L, soy peptone 0.5, $K_2HPO_4\;0.2,\;MgSO_4\cdot7H_2O\; 0.002,\;NaCl\;0.002,\;and\;Na_2CO_3g/L$. Also, the optimal temperature for the production of the protease by Bacillus sp. SJ-121 was about $40^{\circ}C$ at pH 7. The wool and silk were treated with the protease from Bacillus sp. SJ-121. Following the protease treatment, changes in the surface of a single yarn of the fabrics were observed by both an optical microscope and a scanning electron microscope (SEM). Changes in the K/S value of the wool and silk were measured by spectrophotometric analysis, in order to determine the amount of dye uptake in the fabrics. We also performed a tensile strength examination in order to determine the degree and nature of mechanical changes in single yarns of the wool and silk fabrics. By increasing the protease treatment time to 48 h, the dyeing characteristics of the fabrics were enhanced, and the surfaces of the single yarns of the fabrics became smoother, due to the removal of soil and scale in them. However, no mechanical changes were detected in the fabrics. Therefore, we suggest that proper treatment of the protease produced by Bacillus sp. can improve the quality of silk and wool.

• Polymer(Korea)
• /
• v.31 no.1
• /
• pp.31-36
• /
• 2007

It has been reported that the surface properties of the plasma treated material were changed while maintaining its bulk properties. In this study, surface modification of nylon fiber by plasma treatment was tried to attain high water-repellency Nylon fiber was treated with RF plasma under a vacuum system using various parameters such as gas specious, processing time and processing power. Morphological changes by low pressure plasma treatment were observed using scanning electron microscopy (SEM) and atomic force microscopy (AFM). Moreover, the mechanical and inherent properties were analyzed by tensile strength, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The high water-repellency property of nylon fiber was evaluated by a water-drop standard test under various conditions in terms of aging effect. The results showed that the water-repellency of plasma-surface-treated nylon fiber was greatly improved compared to untreated nylon fiber.

• Journal of Conservation Science
• /
• v.26 no.3
• /
• pp.325-334
• /
• 2010

In order to clarify the effect of consolidant, the artificial porous material with low intensity was manufactured using granite powder and Portland cement. We have prepared four kinds of alkoxysilane system consolidants, a acrylic resin and a epoxy resin and investigated about characteristics before and after consolidation. As a result of the research, Silres BS OH 100 was effective for density and surface hardness. SS-101 with hydrophobicity and Site SX-RO with hydrophilicity had the good durability over salts weathering. On the other hand, Syton HT-50 and Paraloid B72 were easily destructed by salt weathering because they were concentrated on surface area by the low penetration depth. Araldite 2020 was the most effective consolidant for improvement of physical properties.

• International Journal of Highway Engineering
• /
• v.12 no.1
• /
• pp.47-54
• /
• 2010

This study had a focus on investigating technical validity of Two-Lift Concrete Pavements which had never been constructed in Korea in order to olve the problem of existing concrete pavements. This study found out the application of Steel Fiber Reinforced Concrete (SFRC) which was one of ew techniques. Also, optimal steel fiber contents and pavement thickness were determined. This study also measured compressive strengths, lexural strengths, toughness indexes, tensile strengths and fatigue strengths to estimate the performance of SFRC of according to results of aboratory experiments, slumps and air contents of concrete specimens the standards satisfied and compressive strengths to open traffic. At bending ests, Toughness Index of SFRC increased but flexural strength didn’'t increase as compared with non-steel fiber concretes. And, energy absorption of SFRC was very good and SFRC showed improvement in freezing and thawing resistances. To complete this research, we will evaluate the pplication methods and performance of SFRC at field section.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.1
• /
• pp.21-25
• /
• 2015

Bending fatigue characteristics of Cu films and $8{\mu}m$ width Cu interconnects on flexible substrates were investigated, and fatigue reliability improvement was achieved through Mo-Ti alloy adhesion layer. Tensile bending fatigue reliability of Cu interconnects is 3 times lower than that of Cu films, and even compressive bending fatigue reliability of Cu interconnects is 6 times lower than that of Cu films. From these results, mechanical crack formation could be fatal in Cu interconnects. With Mo-Ti adhesion layer, fatigue reliability of Cu films and interconnects were enhanced due to the increase of adhesion strength and the suppression of slip induced crack initiation.

• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.194-202
• /
• 1996

Hot melt adhesive based on the polyamide resin was studied to improve the conventional hot melt adhesives such as ethylene-vinyl acetate which have inherent problems against creep and heat resistance. It was found that the terpolymer of nylons6, nylon66, and nylon12 or the nylon blend instead of nylon homopolymer was suitable base resin for hot melt adhesives, since the disruption of regularity in the polymer chains reduced the crystallinity, resulting in lower melting point and melt viscosity. Also, the rheological properties of the polyamide based hot melt adhesive could be controlled by the incorporation of terpene resin, butyl benzyl phthalate, and paraffin wax. The results of melt viscosities and tensile properties of adhesive itself indicated that the optimum adhesion properties could be obtained through the blending of CM831/843P resins with weight ratio 75/25~50/50. The adhesion between steel and steel was tested by using lap shear geometry. It was found that the surface roughness of steel affected the adhesion strength.

• Journal of the Korea Concrete Institute
• /
• v.18 no.5 s.95
• /
• pp.649-656
• /
• 2006

In this study, powered superplasticizer(PSP) agents to improve the slump loss rate of recycled aggregate concrete were developed. To evaluate the variation of fluidity against elapsed time and the mechanical properties, twenty four specimens whose main variables had the mixing condition of aggregates, such as natural and recycled gravels, and natural and recycled fine aggregates, were tested. The concrete slump with a liquid superplasticizer greatly decreased against the elapsed time and dropped by less than 50% of initial slump after two hours. However the concrete slump with the PSP agents hardly varied until after half an hour and maintained more than 85% of initial slump even after an hour. Also the PSP agents made the compressive, splitting tensile, and flexural strength of concrete increased and the shrinkage strain decreased. Considering the properties improvement of concrete, it can be recommended that optimum mixing amount of the PSP agents should be 5% of the amount of cement.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.745-748
• /
• 2008

The past structures were just required bearing capacity to service load, serviceability, and resistance to corrosion. However this point of view has changed after 9.11 terrorism, capacities which can bear impact loading by explosion, and heat by fire happening at the same time, become to be important as a basic condition. The blast resistance capacity of structures is very important part against all over the world is intimidated by terrorism everyday in current point of time. The target of this research is a development of segmented composites and layered structures with high blast resistance using cementitious composites, concrete and FRP composites, which has high tensile strength and ductility, to apply in not only existing facilities but also new ones. Through the improvement of blast resistance, casualties and economic loss can be minimized, and it is possible to diminish the structure collapse and delay the time of structure collapse by thermal effect, impact loading, dynamic loading and high strain.

• Journal of the Korean Society of Costume
• /
• v.57 no.2 s.111
• /
• pp.1-10
• /
• 2007

This study aims at the improvement of sewing function through understandings of dynamic property about the sewing methods and the thread material selection in knitwear. The tensile strength and shear of KES-FB and the Instron were measured for the analysis of the mechanical properties. The knit cloth was structured In the plain stitch, $1\times1$ rib stitch and $2\times1$ rib stitch with the combination of wool and cotton. With regard to the sewing method, intralooping and interlacing were applied. For thread materials, polyester, cotton, wool and silk were used. Since silk has the lowest extension and similar values regardless of its construction in intralooping, it is available knit apparel with uniform elastic recoverv. It also has small shearing resistance. It can be used in apparel which needs big mobility, but it causes rutting problem. Therefore, it is suitable to use intralooping. When the same sewing yarn and textile are use, it can lower shearing resistance and extension in intralooping, Since wool needs a lot of extension energy and it can be cut, intralooping is more suitable than interlacing in sewing of wool. In interlacing using polyester, extension and shearing resistance are high. Therefore, it is suitable for knit sewing with high massing. Silk is not suitable for interlacing since it can be rut. Even though knit materials are different, the RT values of polyester and cotton are similar in same construction. Therefore, they can be substituted each other considering resilience after sewing.

• Composites Research
• /
• v.29 no.6
• /
• pp.336-341
• /
• 2016

This paper conducted the study on the electromagnetic and mechanical applicability of CNT-coated glass fiber for wind blades. Large-size wind blade has the serious pending problems to meet the target, such as interfering radar signals, increasing weights, and increasing repair costs. In this paper, we are suggesting the CNT-coated glass fiber in order to overcome these problems. First, the CNTs were strongly coated on the surfaces of glass fiber by suggested coating process, and the CNT-coated glass fiber/epoxy composites were fabricated by Va-RTM process. We designed and fabricated a radar absorbing structure using the CNT-coated glass fiber, which showed over 90% radar absorbing performance between 8.3 and 12.1 GHz frequency. In addition, we confirmed the improvement of mechanical properties on the strength and modulus of tensile, compressive, and in-plane shear.