• Journal of Welding and Joining
• /
• 제32권4호
• /
• pp.63-68
• /
• 2014

This paper has an aim to study the effect of PWHT and its conditions(peak temperature and holding time) on the tensile properties and impact toughness of FCAW weld metal in relation to microstructure. Impact toughness was evaluated to apply the cargo tank of liquified gas carriers under the various PWHT condition of each class societies. On the basis of these study, it was found that PWHT conditions within all class societies affect charpy absorbed energy of weld metal little or no, all PWHT weld metals kept similar level of charpy absorbed energy as as-weld weld metal down-to $-60^{\circ}C$ and finally indicated lower energy value than that of as-weld weld metal at $-75^{\circ}C$. It is because the precipitation of 2nd phase was controlled from welding consumable and the grain size was grown by PWHT.

• Elastomers and Composites
• /
• 제52권4호
• /
• pp.257-265
• /
• 2017

In this work, CR (Chloroprene Rubber) was emulsified by phase-inversion emulsification with nonionic surfactants (NP-1025, LE-1017, and OP-1019) and an anionic surfactant (SDBS; sodium dodecylbenzenesulfonate), and its stabilization was investigated through a study of its adsorption characteristics, zeta potential, and flow behavior. As the amount of the mixed surfactant increased, the droplet size decreased, resulting in the increase of viscosity. In particular, a CR emulsion with a lower absorbance in the UV spectrum exhibited the highest zeta potential. The results of this experiment showed that the CR emulsion prepared using (LE-1017) and SDBS was the most stable. In this study, calcium hydroxide and aluminum hydroxide were added to enhance the mechanical properties of the CR emulsion, and the relationship between tensile strength, tear strength and surface free energy were investigated. The tensile and tear strengths of the CR emulsion incresed as the amount of calcium hydroxide and aluminum hydroxide increased. The highest tensile and tear strengths and surface free energy were observed for additions of 1.0% calcium hydroxide and 0.80% aluminum hydroxide, respectively. It was concluded that the interfacial bonding strength was improved by the even dispersion of calcium hydroxide and aluminum hydroxide in the CR emulsion.

• 한국자동차공학회논문집
• /
• 제14권3호
• /
• pp.133-141
• /
• 2006

The Low cycle fatigue behavior of 11.7Cr-1.1Mo heat-resisting steel has been investigated under strain-controlled conditions with mean stresses at room temperature and $300^{\circ}C$. For the tensile mean stress test, the initial high tensile mean stress generally relaxed to zero at room temperature, however, at $300^{\circ}C$ initial tensile mean stress relaxed to compressive mean stress. Low cycle fatigue lives under mean stress conditions are usually correlated using modifications to the strain-life approach. Based on the fatigue test results from different stain ratio of -1, 0, 0.5, and 0.75 at room temperature and $300^{\circ}C$, the fatigue damage of the steel was represented by using cyclic strain energy density. Total strain energy density considering mean stress indicated well better than not considering mean stress at $300^{\circ}C$. Predicted fatigue life using Smith-Watson-Topper's parameter correlated fairly well with the experimental life at $300^{\circ}C$.

• 한국기계가공학회지
• /
• 제20권6호
• /
• pp.59-69
• /
• 2021

Directed energy deposition (DED) is an additive manufacturing technology involving a focused high-power laser or electron beam propagating over the substrate, resulting in melt pool formation while simultaneously supplying metal powder to the melt pool area to deposit the material. DED is performed to repair and strengthen parts in various applications, as it can be easily integrate local area cladding and cross-material deposition. In this study, we characterize stainless steel 316 L parts fabricated via DED based on various deposition conditions and geometries to widen the application of DED. The deposition characteristics are investigated by varying the laser power and powder feed rate. Multilayer deposition with a laser power of 362 W and a powder feed rate of 6.61 g/min indicate a height closest to the design value while affording high surface quality. The microhardness of the specimen increases from the top to the bottom of the deposited area. Tensile tests of specimens with two different deposition directions indicate that horizontally long specimens with respect to a substrate demonstrate a higher ultimate tensile strength and yield strength than vertically long specimens with lower elongation.

• 한국세라믹학회지
• /
• 제52권6호
• /
• pp.441-448
• /
• 2015

Silicon carbide (SiC) coatings for tri-isotropic (TRISO) nuclear fuel particles were fabricated using a chemical vapor deposition (CVD) process onto graphite. A micro-tensile-testing system was developed for the mechanical characterization of SiC coatings at high temperatures. The fracture strength of the SiC coatings was characterized by the developed micro-tensile test in the range of $25^{\circ}C$ to $1000^{\circ}C$. Two types of CVD-SiC films were prepared for the micro-tensile test. SiC-A exhibited a large grain size (0.4 ~ 0.6 m) and the [111] preferred orientation, while SiC-B had a small grain size (0.2 ~ 0.3 mm) and the [220] preferred orientation. Free silicon (Si) was co-deposited onto SiC-B, and stacking faults also existed in the SiC-B structure. The fracture strengths of the CVD-SiC coatings, as measured by the high-temperature micro-tensile test, decreased with the testing temperature. The high-temperature fracture strengths of CVD-SiC coatings were related to the microstructure and defects of the CVD-SiC coatings.

• KCI Concrete Journal
• /
• 제12권2호
• /
• pp.85-93
• /
• 2000

Potentially significant mechanical improvements in tension can be achieved by the incorporation of randomly distributed, short discrete fibers in concrete. The improvements due to the incorporation fibers significantly influence the composite stress - strain ($\sigma$-$\varepsilon$) characteristics. In general incorporating fibers in a plain concrete has relatively small effect on its precracking behavior. It, however, alters its post-cracking behavior quite significantly, resulting in greatly improved ductility, crack controls, and energy absorption capacity (or toughness). Therefore, a thorough understanding the complete tensile stress - strain ($\sigma$-$\varepsilon$) response of fiber reinforced concrete is necessary for proper analysis while using structural components made with fiber reinforced concrete. Direct tensile stress applied to a specimen is in principle the simplest configuration for determining the tensile response of concrete. However, problems associated with testing brittle materials in tension include (i) the problem related to gripping of the specimen and (ii) the problem of ensuring centric loading. Routinely, indirect tension tests for plain concrete, flexural and split-cylinder tests, have been used as simpler alternatives to direct uniaxial tension test. They are assumed to suitable for fiber reinforced concrete since typically such composites comprise 98% by volume of plain concrete. Clearly since the post-cracking characteristics are significantly influenced by the reinforcing parameters and interface characteristics, it would be fundamentally incorrect to use indirect tensile tests for determining the tensile properties of fiber reinforced concrete. The present investigation represents a systematic look at the failure and toughening mechanisms and macroscopic stress - strain ($\sigma$-$\varepsilon$) characteristics of fiber reinforced concrete in the uniaxial tension test. Results from an experimental parametric study involving used fiber quantity, type, and mechanical properties in the uniaxial tension test are presented and discussed.

• 대한기계학회논문집A
• /
• 제26권1호
• /
• pp.188-195
• /
• 2002

To investigate the degradation of mechanical properties induced mainly by neutron irradiation, the tensile tests were conducted from room temperature to 300\\`c using the irradiated and the unirradiated Zr-2.5Nb pressure tube materials. The irradiated longitudinal and transverse specimens were collected from the coolant inlet, middle, and outlet parts of M-11 tube which had been operated in Wolsung CANDU Unit-1 and exposed to different operating temperatures and irradiation fluences. The different tensile behavior was characterized not by the fluences of irradiation but by the tensile loading direction. The transverse specimen showed the higher strength and lower elongation than those of the longitudinal one. It was believed that these phenomena resulted from the microstructure anisotropy caused by the extrusion process. The increased strength hardening and decreased elongation embrittlement of the irradiated material were compard to those of the unirradiated one. While the tensile strength of the inlet was higher than that of the outlet, the elongation of the inlet was lower than that of outlet. Considering the operation condition, it was proposed that the operating temperature could be a more effective parameter than the irradiation fluence for long-time life. Through the TEM observation, it was found that while the a-type dislocation density was increased, the c-type dislocation was not changed in the irradiated. The fact that the higher dislocation density was sequentially distributed over the inlet, the middle, and the outlet parts was consistent with the distribution of the tensile strength.

• 한국전산구조공학회논문집
• /
• 제32권4호
• /
• pp.233-240
• /
• 2019

인장 강도는 복합 재료를 설계하기 위한 필수 변수이므로 개방 홀 인장 시험을 통해 복합 재료의 인장 강도를 측정한다. 그러나 인장 시험을 올바르게 모델링하는 것은 섬유와 매트릭스 손상, 층간분리 및 섬유와 매트릭스 사이의 손상 같은 다양한 손상을 수반하기 때문에 매우 어려운 과제다. 따라서 섬유와 매트릭스 사이의 면내 파괴 및 층간분리를 평가하기 위해 본 연구에서는 점진적 손상 모델을 개발하였다. 하신 손상 모델과 응집 영역 접근법을 층과 층간분리를 모델링하는데 사용하였다. 현재 모델의 결과를 이전에 발표된 실험 및 수치 결과와 비교하여 검증하였다. 이를 통해 유한요소해석에서 층간분리를 무시하면 인장 강도가 과대평가 된다는 것을 확인할 수 있었다.

• 폴리머
• /
• 제39권3호
• /
• pp.506-513
• /
• 2015

Ethylidene norbornene(ENB)과 endo-dicyclopentadiene(endo-DCPD) 블렌드를 $1^{st}$ generation과 $2^{nd}$ generation Grubbs 촉매 하에서 ring-opening metathesis polymerization(ROMP)으로 제조하였다. ROMP 과정을 이해하기 위하여 시차주사열분석기(DSC)로 동적 발열거동을 분석하였으며, 반응 후 만능시험기(UTM)로 인장특성을 조사하였다. 반응속도는 endo-DCPD의 양이 적을수록 그리고 $2^{nd}$ generation 촉매 하에서 더 빨라졌다. 또한 endo-DCPD를 첨가할수록 그리고 $1^{st}$ generation 촉매 시스템에서 인장탄성률과 강도는 더 높은 값을 보였으나 강인성은 감소하였다. 이와 같은 인장특성의 변화를 젤 분율 측정과 파단면 관찰을 통하여 자세히 설명하였다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2004년도 추계학술발표회 발표논문집
• /
• pp.963-964
• /
• 2004