• Advances in concrete construction
• /
• 제3권1호
• /
• pp.55-69
• /
• 2015

Tailing Material (TM) and Fly Ash (FA) are obtained as waste products from the mining and thermal industries. Studies were carried out to explore the possibility of utilizing TM as a part replacement to fine aggregate and FA as a part replacement to cement, in concrete mixes. The effect of replacing fine aggregate by TM and cement by FA on the standard sized specimen for compressive strength, split tensile strength, and flexural strengths are evaluated in this study. The concrete mix of M40 grade was adopted with water cement ratio equal to 0.40. Concrete mix with 35% TM and 65% natural sand (TM35/S65) has shown superior performance in strength as against (TM0/S100, TM30/S70, TM40/S60, TM50/S50, and TM60/S40). For this composition, studies were performed to propose the optimal replacement of Ordinary Portland Cement (OPC) by FA (Replacement levels studied were 20%, 30%, 40% and 50%). Replacement level of 20% OPC by FA, has shown about 0-5% more compressive strength as against the control mix, for both 28 day and 56 days of water curing. Interestingly results of split tensile and flexural strengths for 20% OPC replaced by FA, have shown strengths equal to that of no replacement (control mix).

• 터널과지하공간
• /
• 제13권3호
• /
• pp.180-186
• /
• 2003

동적 인장강도를 평가하기 위해 수치해석기법을 이용하여 홉킨슨효과를 가정한 동적 인장시험의 암석 파쇄 과정을 해석하였다. 동적 인장 파쇄 과정과 정적 인장 파쇄 과정에 명확한 차이가 있음을 밝혔으며, 동적 인장강도와 정적 인장강도의 상위는 응력집중현상과 응력재분배에 의해 발생된다는 것을 지적하였다. 그러나 정적파쇄와 동적파쇄 과정에 큰 차이가 있음에도 불구하고 정적 인장강도와 동적 인장강도는 미시적 인장강도의 균질성 계수가 증가함에 따라 미시적 인장강도의 평균치에 근접하였다. 본 연구로부터 암석의 불균질성은 동적 인장강도에 영향을 미치는 요인이며, 동적 인장강도와 정적 인장강도의 상위를 발생시키는 중요한 요인임을 지적하였다.

• 열처리공학회지
• /
• 제13권1호
• /
• pp.1-9
• /
• 2000

The microstructural characteristics and low temperature tensile properties between $25^{\circ}C$ and $-196^{\circ}C$ for as-welded and age hardened specimen by using Al 5083-H321 for base metal, 5083-5356 and 5083-4043 weldments have been investigated. The hardness of 5083-5356 weldment decreases with aging treatment, whereas the weld region of 5083-4043 weldment shows remarkable increase in hardness after aging due to the precipitation of fine Si particle at the grain boundaries and interiors. Low temperature tensile properties of 5083 AI base metal, 5083-5356 and 5083-4043 weldments appear to be the increment of tensile strengths and elongations at the room temperature and $-196^{\circ}C$, while the decrement of tensile properties around $-50^{\circ}C$ is shown. Through the observation of fine serration to fracture in the stress-strain curve and tensile fractography, the increment of localized deformation leading to promote the neck initiation and the increment of the dimple size cause to decrease in tensile strengths and elongations around $-50^{\circ}C$. For the tensile specimen of the 5083 base metal, 5083-5356 and 5083-4043 weldments, the reason to increase in elongation after solution and aging treatment is the diminishment of fine pit, the resolution of Mg into the matrix and the spheridization of the eutectic Si.

• 소성∙가공
• /
• 제31권2호
• /
• pp.89-95
• /
• 2022

3D printing products manufactured by material extrusion are used in many industrial fields recently. However, these products are difficult to use in the field due to their low tensile strengths. In order to solve this problem, research on improving the tensile strength of the output using a 3D printer has been continuously conducted. In this study, we performed a tensile test using Universal Testing Machine according to infill pattern, nozzle temperature, bed temperature, and printing speed conditions. Results revealed that tensile specimen of concentric shape had the highest tensile strength in infill pattern condition and that the tensile strength increased linearly with increasing nozzle and bed temperatures. However, the tensile strength decreased with increasing printing speed. Consequently, we confirmed that tensile strength could be increased and decreased depending on output conditions of 3D printing.

• 한국건설순환자원학회논문집
• /
• 제10권4호
• /
• pp.359-366
• /
• 2022

본 논문에서는 바텀애시 골재를 사용한 다공성 콘크리트의 강도와 컴펙션의 상관관계를 분석하였다. 본 연구에서는 바텀애시를 두 가지 입도의 골재를 8:2 비율로 섞은 복합골재와 단일 입도만을 갖는 단일골재를 사용하여 각 골재 크기별 특성을 파악 한 후, 콘크리트 골재로 사용하였다. 물-바인더 비는 0.30으로 고정하고, 컴펙션 수준을 0.5, 1.5 및 3.0 MPa 값으로 지정하여 다공성 콘크리트 시편을 제작하였다. 총 공극률, 압축강도, 쪼갬인장강도 및 휨인장강도를 실험을 진행하고 분석을 수행하였다. 컴펙션이 증가할 때 총 공극률은 감소하고, 압축강도, 쪼갬인장강도 및 휨인장강도는 증가하였다. 복합골재를 사용한 콘크리트의 총 공극률은 단일골재를 사용한 콘크리트에 비해 총 공극률은 낮고, 강도는 크게 나타났다. 회귀분석을 통해 다공성 콘크리트의 총 공극률, 압축강도, 쪼갬인장강도 및 휨인장강도 상관관계를 제시하였다. 총 공극률과 강도 특성은 서로 반비례하는 상관관계를 나타냈다.

• 한국공간구조학회논문집
• /
• 제17권4호
• /
• pp.159-165
• /
• 2017

In this paper, uniaxial tensile tests of ETFE films with three kinds of thicknesses(100, 200, $250{\mu}m$) and two kinds of directions(machine direction & transverse direction) are performed and the tensile strength, the tensile strain at break and the Young's modulus of ETFE films are compared for two kinds of specimen types(2 & 5). It could be figured out that there are no significant difference between tensile strengths of two specimen types but the tensile strain at break and the Young's modulus of ETFE films are affected by the specimen types. And it is concluded that the uniaxial tensile test of specimen type 2 are more reliable than that of specimen type 5.

• 한국농공학회논문집
• /
• 제48권1호
• /
• pp.51-60
• /
• 2006

This study was conducted to investigate experimentally the drying shrinkage and the strength properties of redispersible SBR and PAE powder-modified mortars. Polymer-cement ratio, content of shrinkage-reducing agent and antifoamer content were manipulated as the experimental variables. The peculiarity of this study is to obtain a high early-age strength by using the portland cement and alumina cement with the ratio of 8 : 2. Until 7 days of age, the drying shrinkage remarkably increased up to $1\~2\times10^{-4}$, while it tended to decrease as the ratio of polymer to cement ratio and the content of shrinkage-reducing agent increased. Polymer-cement ratio was effective in improving the flexural, tensile and adhesive strengths: As the ratio increased, the strengths correspondingly increased. The flexural strength was in the range of $7\~11$ MPa, the tensile strength was $3.5\~5$ MPa and the adhesive strength was $1.2\~3.9$ MPa. On the other hand, the compressive strength tended to decrease as the polymer-cement ratio increased, and it was in the range of $23\~39$ MPa. All strengths, flexural, tensile, adhesive and compressive strengths, decreased as the content of powder shrinkage-reducing agent increased. It turned out that the polymer-cement ratio influenced more on the behavior of drying shrinkage and the properties of strength than the powder shrinkage-reducing agent did.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권4호
• /
• pp.107-115
• /
• 2012

본 연구에서는 경량 콘크리트에 대한 361개, 보통중량 콘크리트에 대한 1,335개 및 고중량 콘크리트에 대한 221개의 데이터를 이용하여 콘크리트의 인장강도 (직접인장강도, 쪼갬인장강도 및 파괴계수)에 대한 설계기준과 기존 연구자들의 제안모델의 안정성을 평가하였다. 콘크리트 인장강도 예측을 위한 대부분의 제안 식들은 보통중량 콘크리트의 실험결과를 이용하여 압축강도의 함수로서 제시되었다. 하지만 데이터베이스의 분석은 콘크리트 인장강도는 기건 단위질량에 의해서도 중요한 영향을 받음을 보여준다. 이에 따라, 콘크리트 인장강도에 대한 기준 및 제안모델들은 기건 단위질량 2,100 $kg/m^3$ 이하, 압축강도 50 MPa 이상에서는 실험결과와의 불일치가 증가하였다. 한편, 본 연구에서 콘크리트 기건 단위질량을 고려하여 제시된 콘크리트 인장강도 예측 모델들은 실험결과와 비교적 잘 일치하였다.

• 전기학회논문지
• /
• 제65권9호
• /
• pp.1518-1523
• /
• 2016

In this study, in order to understand the degradation characteristics of oil-paper insulation for power transformers and OF cables, tan delta was measured using cable model specimens with long-term accelerated thermal and electrical aging. In addition, to find out the degradation level due to the accelerated aging, tensile strengths of aged papers were measured. As a result, tan ${\delta}$ showed the characteristics of slight decrease at the first stage and then increase with the aging time, which could be analyzed due to the evaporation of remaining moisture and the change of aging rate with time. Also, the trend of tensile strengths with aging temperature and time was appeared to be exponentially decreased and by use of these data equivalent calculated lifetimes and accelerated aging factors were derived for each aging temperatures. After then, tan ${\delta}$ was analyzed with the equivalent operating years. For all different aging temperatures, the aged data were very well fit to the equivalent operating years and it is shown that tan ${\delta}$ was increased with the decrease of tensile strength.

• 터널과지하공간
• /
• 제2권2호
• /
• pp.224-236
• /
• 1992

It is very important to determine the thermo-mechanical characteristics of the rock mass surrounding the repository of radioctive waste and the LPG storage cavern. In this study, Hwasoon-Shist. Dado-Tuff adn Chunan-Tonalite were the selected rock types. Temperature dependence of the mechanical properteis such as uniaxial compressive strength, tensile strength, Young's modulus was investigated by measuring the behaviour of these properties due to the variation of temperature. Also, the characteristics of strength and deformation of these rocks were examined through high-temperature triaxial compression tests with varing temperatures and confining pressures. Important results obtained are as follows: In high temperature tests, the uniaxial compressive strength and Yong's modulus of Tonalite showed a sligth increase at a temperature up to 300$^{\circ}C$ and a sharp decrease beyond 300$^{\circ}C$, and the tensile strength showed a linear decrease with increasing heating-temperature. In high-temperature triaxial compression test, both the failure stress and Young's modulus of Tonalite increased with the increase of confining pressure at constant heating-temperature, and the failure stress decreased at 100$^{\circ}C$ but increased at 200$^{\circ}C$ under a constant confining pressure. In low temperature tests, the uniaxial compressive and tensile strengths and Young's modulus of these rocks increased as the cooling-temperature is reduced. Also, the uniaxial compressive and tensile strengths of wet rock specimens are less than those of dry rock specimens.