• 대한금속재료학회지
• /
• 제46권10호
• /
• pp.672-682
• /
• 2008

The resistance spot welding of TRIP590 steels was investigated to enhance understanding of weld fracture during tensile-shear strength (TSS) test. The main failure modes for spot welds of TRIP590 steels were nugget pullout and interfacial fracture. The peak load to cause a weld interfacial failure was found to be related to fracture toughness of the weld and the weld diameter. Although interfacial fracture occurred in the samples, the load carrying capacity of the weld was high and not significantly affected by the fracture mode. Substantial part of the weld exhibits the characteristic dimple (or elongated dimple) fractures on interfacial fractured surface, in spite of the high hardness values associated with the martensite microstructures. The high load-bearing ability of the weld is directly associated with the area of ductile fracture occurred in weld. Therefore, the judgment of the quality of resistance spot welds in TRIP590 steels, the load carrying capacity of the weld should be considered as an important factor than fracture mode.

• 한국강구조학회 논문집
• /
• 제15권2호
• /
• pp.137-145
• /
• 2003

본 연구에서는 국산 PS 강봉의 직경, 반복최소응력 및 반복최대응력 등을 실험변수로 하여 직접 인장 피로실험을 수행하였다. 정적 인장실험 결과, 국산 PS 강봉의 응력 - 변형률 곡선과 극한강도 등을 얻었다. 또한, 피로실험에서의 특징적인 실험결과는 PS 강봉의 직경은 피로 수명에 중요한 인자가 아니며, 반복 최소응력의 크기는 국산 PS 강봉의 피로수명에 매우 큰 영향을 미치는 것으로 나타났다. 이러한 피로실험결과를 통계 분석하여 PS 강봉의 응력 범위 및 반복 최소응력 등을 변수로 하는 피로강도 예측식을 제안하였다. 피로실험 중, 시편중앙에 설치한 Extensometer를 이용하여, 변형률의 변화를 측정하였으며, 측정된 변형률 변화현상에서 탄성계수의 변화현상을 구하였다. 변형률 증가현상은 3단계의 형태 즉, 초기에 급격한 증가 후 서서히 증가하며 파괴 직전에 급격하게 증가하는 형태로 나타났다. 탄성계수의 변화현상은 변형률 변화현상과 유사하게 감소하는 것으로 나타났으며 응력수준은 탄성계수 변화에 큰 영향을 주지 않는 것으로 나타났다.

• 비파괴검사학회지
• /
• 제7권2호
• /
• pp.42-47
• /
• 1988

이상의 결과를 요약하면 다음과 같다. 1) 초음파 C-scan 법에 의하여 층간분리, 기지균열 등의 손상 정도, 크기 및 형태의 판별이 가능하며 충격손상은 주로 섬유의 주축방향으로 성장한다. 2) 복합재료의 인장파괴시 적층구조에 따라 상이한 AE 양상을 나타내며 이 원인은 파괴 mode의 차이에 기인한다. 3) 섬유의 파단은 기지파단의 경우 보다 강력한 AE activity를 나타내며 peak amplitude의 분포를 분석하여 파괴 mode의 해석이 가능하다. 4) 복합재료의 파괴강도는 적층구조, 충격 손상 등에 영향을 받으며 응력파 계수(SWF)의 측정에 의해 정성적 평가가 가능하다.

• Computers and Concrete
• /
• 제16권2호
• /
• pp.209-222
• /
• 2015

This paper presents results of biaxial compressive tests and strength criterion on two replacement percentages of recycled coarse aggregate (RPRCA) by mass for plain structural recycled aggregate concrete (RAC) at all kinds of stress ratios. The failure mode characteristic of specimens and the direction of the cracks were observed and described. The two principally static strengths in the corresponding stress state were measured. The influence of the stress ratios on the biaxial strengths of RAC was also analyzed. The experimental results showed that the ratios of the biaxial compressive strength ${\sigma}_{3f}$ to the corresponding uniaxial compressive strength $f_c$ for the two RAC are higher than that of the conventional concrete (CC), and dependent on the replacement percentages of recycled coarse aggregate, stress states and stress ratios; however, the differences of tensile-compressive ratios for the two RAC and CC are smaller. On this basis, a new failure criterion with the stress ratios is proposed for plain RAC under biaxial compressive stress states. It provides the experimental and theoretical foundations for strength analysis of RAC structures subject to complex loads.

• Geomechanics and Engineering
• /
• 제24권2호
• /
• pp.157-166
• /
• 2021

This paper aims at the temperature and slenderness ratio effects on physical and mechanical properties of Beishan granite. A series of uniaxial compression tests with various slenderness ratios and temperatures were carried out, and the acoustic emission signal was also collected. As the temperature increases, the fracture aperture of intercrystalline cracks gradually increases, and obvious transcrystalline cracks occurs when T > 600℃. The failure patterns change from tensile failure mode to ductile failure mode with the increasing temperature. The elastic modulus decreases with the temperature and increases with slenderness ratio, then tends to be a constant value when T = 1000℃. However, the peak strain has the opposite evolution as the elastic modulus under the effects of temperature and slenderness ratio. The uniaxial compression strength (UCS) changes a little for the low-temperature specimens of T < 400℃, but a significant decrease happens when T = 400℃ and 800℃ due to phase transitions of mineral. The evolution denotes that the critical brittle-ductile transition temperature increases with slenderness ratio, and the critical slenderness ratio corresponding to the characteristic mechanical behavior tends to be smaller with the increasing temperature. Additionally, the AE quantity also increases with temperature in an exponential function.

• 대한기계학회논문집A
• /
• 제34권4호
• /
• pp.481-486
• /
• 2010

Carbon Fiber Reinforced Plastic(CFRP) 복합재료는 높은 비강성 및 우수한 화학적 특성 등으로 인하여 여러분야에서 점점 사용이 증가하고 있다. 대부분의 CFRP 복합재료는 여러 부품들의 조립을 통해 제작된다. 이러한 독립된 부품들은 볼트, 핀 등과 같은 기계적인 방법을 통해 체결된다. 볼트나 핀에 의한 hole은 구조내에서 노치로 작용하여 부품의 강도저하의 원인이 된다. 본 논문에서는 홀의 크기와 시험편 폭이 노치재의 파괴강도에 끼치는 영향을 평가하여 hole을 포함하고 있는 평직 CFRP 복합재료의 정하중 파괴 강도를 실험적으로 평가하였다. 이를 위하여 본 논문에서는 홀 크기와 시험편 폭에 따른 점응력 조건의 특성길이를 평가하였으며, 특성길이와 노치재의 파괴강도의 관계를 확인하였다. 이를 이용하여 노치재의 정하중 파괴기준을 재정의하였다.

• 대한조선학회논문집
• /
• 제41권6호
• /
• pp.75-83
• /
• 2004

Ice rubble pieces broken by the bow impact load and side hull of an icebreaking vessel usually pass along the ship's bottom hull and may hit the propeller/rudder or other stern structures causing serious damage to ship's hull . Therefore it is important to estimate the size of broken ice pieces during the icebreaking process. The dynamic interaction process of icebreaker with infinite ice sheet is simplified as a wedge type beam of finite length supported by elastic foundation. The wedge type ice beam is leaded with vertical impact forces due to the inclined bow stem of icebreaking vessels. The numerical model provides locations of maximum dynamic bending moment where extreme tensile stress arises and also possible fracture occurs. The model can predict a failure length of broken ice sheet given design parameters. The results are compared to Nevel(1961)'s analytical solution for static load and observed pattern of ice sheet failure onboard an icebreaker. Also by comparing computed failure length with the characteristic length, the meaning of ice rubble sizes is discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.275-278
• /
• 2005

INCONEL 718, nickel based superalloy, has good formability, high strength, excellent corrosion resistance and mechanical properties at high temperature. Owing to theses attractive properties, it finds use in applications such as combustion system, turbine engines and nuclear reactors. In such applications, components are typically required to be tolerant of high stress impact loading. This may cause material degradation and lead to catastrophic failure during service operation. In order to design optimal structural parts made of INCONEL 718, accurate understanding of material's mechanical properties, dynamic behavior and fracture characteristic as a function of strain rates are required. This paper concerned with the dynamic material properties of the INCONEL 718 for the various strain rates. The dynamic response of the INCONEL 718 at intermediate strain rate is obtained from the high speed tensile test machine test and at the high strain rate is from the split Hopkinson pressure bar test. Based on the experimental results, the effects of strain rate on dynamic flow stress, work hardening characteristics, strain rate sensitivity and elongation to the failure are evaluated. Experimental results from both quasi-static and high strain rate up to the 5000/sec are interpolated in order to construct the Johnson-Cook model as the constitutive relation that should be applied to simulate and design the structural parts made of INCONEL 718.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.262-267
• /
• 2001

In this study, the Reliability of degraded steam turbine blade was evaluated using the limited fatigue data. The statistical estimation of limited fatigue data implies that some unknown uncertainties which may be involved in fatigue reliability analysis. Therefore, an appropriate distribution in the fatigue strength was determined by the characteristic distribution - linear correlation coefficient, fatigue physics, error parameter. 3-parameter Weibull distribution is the most appropriate distribution to assume for infinite region. The load applied on the blade is mainly tensile. The maximum Von-Mises stress is 219.4 MPa at the steady state service condition. The failure probability($F_p$) derived from the strength-stress interference model using Monte carlo simulation under variable service condition is 0.25% at the 99.99% confidence level.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.279-286
• /
• 2002

Recently, there are many attempts to expand a temporary soil nailing system into a permanent wall due to the advantage of soil nailing system, that is efficient and economic use of underground space and decreasing the total construction cost. However, the proper design approach of a permanent soil nailing system has not been proposed by now in Korea. Permanent soil nailing system which utilizes precast concrete walls for the facing of soil nailing system Is already used in many countries. In general, the cast-in-place concrete facings or rigid walls were constructed in bottom-up way after construction of soil nailing walls finished preliminarily In this paper, various laboratory model tests have been carried out to investigate the failure mode, behavior characteristics, and tensile force at nail head in each load level in respects of the variation of stiffness of the facing.