• 비파괴검사학회지
• /
• 제14권2호
• /
• pp.101-111
• /
• 1994

전자처리스페클패턴간섭법을 CW 레이저에 비디오 시스템과 화상 처리 장치를 조합하여 평판의 변위를 측정하는데 이용하였다. 과거의 스트레인 게이지나 모아레법과는 달리 전자처리스페클패턴간섭법(ESPI)은 측정물에 아무런 처리를 할 필요가 없고, 완전한 비접촉 측정이 가능하며, 또한 감도가 높은 이점이 있다. 본 연구에서 사용한 시험편은 로드셀과 같은 방향으로 하중이 걸리도록 하였다. 시험편은 평판이고 스트레인 게이지를 부착하였다. 이 연구는 전자처리스페클패턴간섭법에 의해 변위와 응력 분포를 구하여 스트레인 게이지와의 비교함으로써 전자처리스페클패턴간섭법의 측정 정밀도에 대해 검토하고자 한다.

• Geomechanics and Engineering
• /
• 제5권5호
• /
• pp.463-483
• /
• 2013

Considering the influences of fluid penetration, casing, excavation processes of wellbore and perforation tunnels, the seepage-deformation finite element model of oil and gas well coupled with perforating technique is established using the tensile strength failure criterion, in which the user-defined subroutine is developed to investigate the dynamic evolvement of the reservoir porosity and permeability. The results show that the increases of perforation angle and decreases of perforation density lead to a higher fracture initiation pressure, while the changes of the perforation diameter and length have no evident influences on the fracture initiation pressure. As for initiation location for the fracture in wellbore, it is on the wellbore face while considering the presence of the casing. By contrast, the fractures firstly initiate on the root of the tunnels without considering casing. Besides, the initial fracture position is also related with the perforation angle. The fracture initiation position is located in the point far away from the wellbore face, when the perforation angle is around $30^{\circ}$; however, when the perforation angle is increased to $45^{\circ}$, a plane fracture is initiated from the wellbore face in the maximum horizontal stress direction; no fractures was found around perforation tunnels, when the angel is close to $90^{\circ}$. The results have been successfully applied in an oilfield, with the error of only 1.1% comparing the fracture initiation pressure simulated with the one from on-site experiment.

• Environmental Engineering Research
• /
• 제21권3호
• /
• pp.233-240
• /
• 2016

The research aims to study the different flexible rubber tube diffusers used in urban wastewater treatment processes and aquaculture systems. The experiment was conducted in small-scale aeration tank with different physical properties of the tubes that were used as aerators. The volumetric mass transfer coefficient ($k_La$), oxygen transfer efficiency (OTE) and aeration efficiency (AE) were measured and determined to compare the diffusers. Moreover, the bubble hydrodynamic parameters were analyzed in terms of bubble diameter ($d_B$) and rising velocity ($U_B$) by a high speed camera (2,000 frames/s). Then the interfacial area (a) and liquid-side mass transfer coefficient ($k_L$) can be calculated. The physical properties (tube wall thickness, tensile strength, orifice size, hardness and elongation) have been proven to be the key factor that controls the performance (kLa and OTE). The effects of hardness and elongation on bubble formation, orifice size and a-area were clearly proved. It is not necessary to generate too much fine bubbles to increase the a-area: this relates to high power consumption and the decrease of the kL. Finally, the wall thickness, elongation and hardness associated of the flexible tube diffuser (tube No. 12) were concluded, to be the suitable properties for practically producing, in this research.

• 한국재료학회지
• /
• 제21권1호
• /
• pp.34-38
• /
• 2011

In this study, the effects of an annealed buffer layer with different thickness on heterojunction diodes based on the ZnO/ZnO/p-Si(111) systems were reported. The effects of an annealed buffer layer with different thickness on the structural, optical, and electrical properties of zinc oxide (ZnO) films on p-Si(111) were also studied. Before zinc oxide (ZnO) deposition, different thicknesses of ZnO buffer layer, 10 nm, 30 nm, 50 nm and 70 nm, were grown on p-Si(111) substrates using a radio-frequency sputtering system; samples were subsequently annealed at $700^{\circ}C$ for 10 minutes in $N_2$ in a horizontal thermal furnace. Zinc oxide (ZnO) films with a width of 280nm were also deposited using a radio-frequency sputtering system on the annealed ZnO/p-Si (111) substrates at room temperature; samples were subsequently annealed at $700^{\circ}C$ for 30 minutes in $N_2$. In this experiment, the structural and optical properties of ZnO thin films were studied by XRD (X-ray diffraction), and room temperature PL (photoluminescence) measurements, respectively. Current-voltage (I-V) characteristics were measured with a semiconductor parameter analyzer. The thermal tensile stress was found to decrease with increasing buffer layer thickness. Among the ZnO/ZnO/p-Si(111) diodes fabricated in this study, the sample that was formed with the condition of a 50 nm thick ZnO buffer layer showed a strong c-axis preferred orientation and I-V characteristics suitable for a heterojunction diode.

• Macromolecular Research
• /
• 제14권2호
• /
• pp.179-186
• /
• 2006

In the present work, low density polyethylene (LDPE)/aliphatic polyester (APES)/organoclay ternary nanocomposites were prepared. In particular, the effect of a compatibilizer, polyethylene-graft-maleic anhydride (PE-g-MAH), on the morphology and properties of the ternary nanocomposites was investigated. LDPE/APES/organoclay nanocomposites were prepared through melt intercalation method using two different kinds of organoclay. The dispersibility of silicate clays in the nanocomposites was investigated by X-ray diffraction and atomic force microscopy. The ternary nanocomposites showed higher tensile properties than the LDPE/APES blend did. The dispersibility and properties of nanocomposites containing Cloisite 30B were better than those of the nanocomposites containing Cloisite 20A. Unlike Cloisite 20A, hydroxyl groups in the intercalants in Cloisite 30B interlayer underwent a certain polar interaction with the carboxyl group of APES, favoring the intercalation of APES chains and the formation of LDPE/APES/Closite 30B nanocomposites. However, the introduction of the polar hydroxyl groups also enhanced the interaction with the silicate surface at the same time, thereby rendering somewhat difficult the replacement of the surface contacts by LDPE chains, and impeding the extensive intercalation and further exfoliation of Cloisite 30B in the LDPE/APES matrix. The compatibilizer enhanced the intercalation of the polymer chain inside the clay gallery and thus improved the mechanical properties of the ternary nanocomposites. Rheological measurements of the nanocomposites via frequency sweep experiment indicated a certain interaction between the clay platelet and the polymer molecules in the melted state.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.539-544
• /
• 2002

Titanium and titanium alloy are excellent in corrosion resistance and specific intensity, and also in the biocompatibility. On the other hand, the brazing is bonding method of which productivity and reliability are high, when the complicated and precise structure of the thin plate is constructed. However, though conventional titanium-based brazing filler metal was excellent in bond strength and corrosion resistance, it was disadvantageous that metal structure and mechanical property of the base metal deteriorated, since the brazing temperature (about 1000 C) is considerably high. Authors developed new brazing filler metal which added Zr to Ti-Cu (-Ni) alloy which can be brazed at 900 C or less about 15 years ago. In this paper, the development of more low-melting-point brazing filler metal was tried by the addition of the fourth elements such as Ni, Co, Cr for the Ti-Zr-Cu alloy. As a method for finding the low-melting-point composition, eutectic composition exploration method was used in order to reduce the experiment point. As the result, several kinds of new brazing filler metal such as 37.5Ti-37.5-Zr-25Cu alloy (melting point 825 C) and 30Ti-43Zr-25Cu-2Cr alloy (melting point: 825 C) was developed. Then, the brazing joint showed the characteristics which were almost equal to the base metal from the result of obtaining metallic structure and strength of joint of brazing joint. However, the brazing filler metal composition of the melting point of 820 C or less could not be found. Consequentially, it was clarified that the brazing filler metal developed in this study could be practically sufficiently used from results such as metal structure of brazing joint and tensile test of the joint.

• 콘크리트학회논문집
• /
• 제26권3호
• /
• pp.323-329
• /
• 2014

화력발전소에서 발생되는 플라이애쉬는 콘크리트의 첨가재로 사용되는 것이 석탄회 재활용 방안 중 최선으로 알려져 있다. 이러한 석탄회는 최근 더 이상 매립이 불가능하여 콘크리트에 다량 첨가가 시도되고 있다. 그럼에도 불구하고 현재까지 하이볼륨 플라이애쉬(High Volume Fly Ash: HVFA) 시멘트 콘크리트의 연구분야는 주로 재료적인 분야에 대해서만 수행되어지고 있는 실정이다. 그러나 하이볼륨 플라이애쉬 시멘트 콘크리트의 구조재료로의 적용을 위해서는 탄성계수, 응력-변형률 관계 및 구조 부재 거동 등에 대한 연구가 필수적이다. 이를 위하여 이 논문에서는 플라이애쉬 치환율 0, 35 및 50%, 압축강도 20, 40 및 60 MPa 그리고 인장철근비 2수준을 실험변수로 하여 플라이애쉬 시멘트 철근콘크리트 보 18개를 제작하여 이들의 휨거동을 실험적으로 평가하였다. 실험결과에 의하면 플라이애쉬를 첨가하지 않은 일반 콘크리트(FA=0%)와 35, 50% 플라이애쉬 시멘트 콘크리트 부재의 휨거동은 크게 차이나지 않음을 알 수 있었다.

• 한국해양공학회지
• /
• 제20권6호
• /
• pp.88-92
• /
• 2006

Large-scale model tests of welded topside joints were carried out to observe the fatigue behavior of API 2W Gr.50 steel produced by POSCO. The fatigue crack behaviors for various loading conditions were measured and investigated around the critical joint sections. The experimental results have been verified with numerical approaches and also compared with the AWS D1.1 and DnV RP-C203 design curves. The large-scale experiment models were fabricated, based on the actual operating east area fixed platform. The dimensions of the models were slightly modified to accommodate the test facilities and capacities. The fatigue test was carried out having ${\Delta}Q$ of T1=705.6kN, T2=749.7kN and T3=793.8kN. The three specimens were statically loaded 20 times, with various loadings of about 50kN intervalsbetween the maximum and minimum loads required in the fatigue tests. This loading removed the residual stress in the specimen before the fatigue tests. The topside joint crack was initiated from the brace heel, where the maximum tensile stress occurred. The API 2W Gr.50 steel satisfied the AWS D1.1 detail category C and DnV RP-C203 detail category F ${\Delta}S-N$ curve.

• 비파괴검사학회지
• /
• 제32권1호
• /
• pp.27-33
• /
• 2012

광탄성법은 실험역학에서 응력 또는 변형률을 해석하기 위한 여러 실험방법 중의 하나이며, 다양한 종류의 구조물의 응력 분포를 실험적으로 결정하는 기법이다. 광탄성법은 광탄성 영상의 등색 프린지와 등경 프린지로부터 광탄성 시편에 나타나는 전체의 응력장 분포를 정밀하게 측정할 수 있다. 본 논문에서는 여러 가지 광탄성 기법중 8단계 위상이동법(8-step phase-shifting method)에 관한 이론을 살펴보고, 경사균열이 있는 평판 시편에 인장을 가하여 나타난 광탄성 프린지로부터 경사균열 선단주위의 응력분포를 8단계 위상이동법으로 결정한 후, 이들 결과를 유한요소법(FEM)에 의한 결과와 비교하였다. 8단계 위상이동법을 이용한 실험에 의해 측정된 프린지 차수는 유한요소법에 의한 계산된 프린지 차수값에 근접하였다.

• Journal of Welding and Joining
• /
• 제29권1호
• /
• pp.80-84
• /
• 2011

The weight reduction of the transportations has become an important technical subject Al and Al alloys, especially Al 5052 alloys have been being applied as door materials for automobile. One of the most widely known car weight-reduction methods is to use light and corrosion-resistant aluminum alloys. However, because of high electrical and thermal conductivity and a low melting point, it is difficult to obtain good weld quality when working with the aluminum alloys. Also, Pulse MIG welding is the typical aluminum welding process, but it is difficult to apply to the thin plate, because of melt-through and humping-bead. In order to enhance weld quality, welding parameters should be considered in optimizing the welding process. In this experiment, Al 5052 sheets were used as specimens, and these materials were welded by adopting new Cold Metal Transfer (CMT) pulse process. The proper welding conditions such as welding current, welding speed, torch angle $50^{\circ}$ and gap 0~1mm are determined by tensile test and bead shape. Through this study, range of welding current are confirmed from 100A to 120A. And, the range of welding speed is confirmed from 1.2m/min to 1.5m/min.