• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2002.05a
• /
• pp.153-160
• /
• 2002

This paper shows the possibility of performing Lap joint using the friction stir welding and the determination of tool's dimensions for FSW in Milling machine. This research also is reported on obtaining the tensile-shear strength, 9.319 ( kgf/mm$^{2}$) and the energy absorption, 2,682 (kgf-mm) under this experiment. The optimal tool's dimensions and method for Lap joint in 2tmm aluminum alloy plate using FSW is as follows; The diameter of shoulder and pin are 9 $\phi$mm and 3$\phi$mm, the length of pin is 3.6mm. The conditions of shoulder of tool is not pressed into original base metal.

• The Journal of Natural Sciences
• /
• v.8 no.2
• /
• pp.191-198
• /
• 1996

We were investigated the change of shrinkage, pilling, tensile strength, color fastness and staining of Cotton, Nylon, Cotton/Nylon(60/40) socks after wearing and washing. From the experiment we found that color fastness of the color socks decreased corresponding to the frequency of wearing and washing. Our results showed that color fastness in the case of Cotton is best among them. Shrinkage was significant in Nylon/Cotton and Cotton socks. In the experiment of male and female socks, male showed a greater evidence of staining, shrinkage and pilling than female.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.69-75
• /
• 2019

Oil seals have a great effect on transmission performance and durability. In this study, the optimal rubber mix was derived using dispersion analysis to obtain excellent oil-seal rubber properties. ANOVA was performed twice. The factors were polymers, carbon, magnesium oxide, and calcium hydroxide, which were used as four factors in ANOVA. The response factors were four items (hardness, tensile strength, elongation rate, and compression deformation) obtained through an experiment with a confidence level of 95%. In the first ANOVA, 168 tests were performed, and in the secondary ANOVA, 24 physical tests were conducted using polymers and carbon derived from the primary ANOVA. Through the ANOVA, we derived a rubber mixture recipe.

• Composites Research
• /
• v.16 no.4
• /
• pp.10-21
• /
• 2003

Proposed is a new method to determine the characteristic lengths for the failure analysis of composite joint without experiments. New method uses the result that the stress distribution in the characteristic length specimens is linearly proportional to the applied load. The compressive characteristic lengths calculated by the present method are exactly same as the lengths obtained by the conventional method based on experiment. The new tensile characteristic length is defined using the strength of the notched laminate, while previous methods use the strength of the sound laminate. That change allows calculating the tensile characteristic length numerically without experiment like the compressive characteristic length. Finite element analyses are conducted by MSC/NASTRAN. The interface between the fastener and laminate is modeled by the contact surface element. The finite element results based on the new characteristic lengths show the excellent agreement with experimental results for the Graphite/Epoxy composite .joints.

• Laser Solutions
• /
• v.7 no.2
• /
• pp.1-10
• /
• 2004

This work was attempted to join SCP sheet and STS304 sheet by using Nd:YAC laser beam. SCP sheet has good formability and low cost, while STS304 has excellent corrosion resistance and mechanical properties in high temp. In this experiment, butt joint type was used to develop the tailored blank welding for dissimilar steel. Sheets which have different thermal properties. Computer simulation was conducted to obtain the off-set position for efficient welding by considering laser power, scanning speed, focal length and basic properties. The result showed that the optimum thermal distribution was obtained when the laser beam was irradiated at $0.05{\sim}0.1$ mm off-set toward the SCP sheet side. The experiment was conducted based on the result of computer simulation to show the same optimum conditions. Optimum conditions were 3KW in laser beam power, 6m/min in scanning speed, -0.5mm in focal position, 0.1mm off-set toward SCP. Microhardness test, tensile test, bulge test, optical microscopy, EDS, and XRD were performed to observe the microstructure around fusion zone and to evaluate the mechanical properties of optimum conditions, The weld zone had high microhardness values by the formation of the martensitic structure. Tensile test measured the strength of welded region by vertical to strain direction and the elongation of welded region by parallel to strain direction. Bulge test showed $52\%$ formability of the original materials. Bead shape, grain size, and martensitic structure were observed by the optical microscopy in the weld zone. Detailed results of EDS, XRD confirmed that the welded region was connected of martensitic structure.

• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.107-114
• /
• 2013

In this study we experimentally evaluated an impact resistant performance of fiber reinforced concrete in the moment of explosion by high-velocity projectile with emulsion explosive. To assess the impact resistance, we conducted the impact test of high-velocity projectile which reaches an impact speed of 350 m/s and the experiment of contact exploding emulsion explosive. As a result, bending and tensile performance depending on type of PVA, PE fiber (polyvinyl alcohol fiber, polyethylene fiber) and steel fiber affects destruction of rear side in the form of spalling. Destroying the backside of the concrete compressive strength compared to suppress the bending and tensile performance is affected. In addition, the experiment shows that the destruction patterns of concrete specimen producted by high velocity impact and contact explosion are significantly similar. Therefore, it is possible to predict the destruction patterns of specimens in the situation of contact explosion by high-velocity projectile.

• Composites Research
• /
• v.28 no.5
• /
• pp.285-290
• /
• 2015

Multiscale multiphysics in structural batteries make mechanical property testing difficult. In this research, the effect of electrolyte-coating on the mechanical performance of carbon fabric was studied using a suitable mechanical test method for structural batteries. For this experiment, two types of specimens were determined their dimension according to ASTM. One type of specimen was smaller than the standard dimension. The specimens were coated by spreading the electrolyte material on carbon fabric, hardened using epoxy, and tested for tensile properties using universal testing machine. As a result, it was found that the mechanical properties of carbon fabric were not influenced by electrolyte coating. In addition, the small-scale specimen used in this experiment was determined to be sufficiently reliable.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.5 s.66
• /
• pp.561-570
• /
• 2003

This study evaluate the characteristics of stainless steel for the use of stainless steel tubes as structural members. The strength of stainless steel tube was compared with that of steel tube stub-columns through tensile experiment and compressed experiment. The selected experimental parameters were diameter (width)-thickness and section shape. The results of tests showed that stainless steel tubes could be predicted as superior to steel tubes in terms of tensile strength, yield ratio, elongation percentage, and absorption ability of energy. The yield strength of stainless steel tubes were found to be higher than the Korean Standards ($Fy=2.1tf/cm^2$) and the design strength of SIJ-ASD($Fy=2.4tf/cm^2$). It was also higher then the yield strength of steel tubes. The plastic deformation of stainless steel tubes was found to beto that of steel tubes.

• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.284-290
• /
• 1993

The soap-free emulsion polymerization was carried out for Styrene/Butadiene system with Acrylonitrile as hydrophilic comonomer and KPS as initiator. Under the condition of below 50% conversion, the dependence of Rp on $[AN]^n$ and $[KPS]^n$ was found to be n=1.617-1.050 and n=0.83-0.96 for [AN] and [KPS], respectively. The effect of $[AN]^n$ and $[KPS]^n$ on particle number density (Np) was determined to be n=1.533 and n=0.733, respectively. The highest conversion was obtained under the conditions of pH=5 and ratio of total monomer (g) to water (g)=0.5. The mechanical properties of SBR obtained in this experiment were shown to be inferior to commercial SBR in terms of tensile strength, 300% modulus and elongation. It was found that cure rate of SBR prepared in this experiment was faster than that of commercial SBR.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.1
• /
• pp.35-41
• /
• 2020

The thin coating material used in the outer insulation finishing method is a finishing material mainly based on acrylic emulsion. In this study, the properties of silane modified acrylic emulsion and silica dispersed acrylic emulsion were evaluated. Experimental results showed that the silane modified acrylic emulsion had no significant effect on improving tensile strength, but was effective in improving the performance of adhesion strength, water absorption coefficient, and hot and cold repeat resistance. Silica-dispersed acrylic emulsions were effective in improving tensile strength, and at 10% substitution rate, they were effective in improving the performance of adhesion strength, water absorption coefficient and hot / cold resistance. Through this, it was judged that a composite emulsion capable of improving the performance of the acrylic emulsion could be prepared.