• KIEAE Journal
• /
• v.9 no.1
• /
• pp.85-90
• /
• 2009

The indoor air quality is one of the most important issues of designing ventilation in high rise apartment buildings. This study suggested proper ventilation rate in the apartment bedroom where mechanical ventilation system has installed. Six university students(four male and two female) were participating in the experiment. Experiments were performed in environmental chamber. Experimental conditions were combinations from three ventilation rate 0, 0.4 and 0.7. Measurement items during 8 hours of experimental time were temperature, humidity, carbon dioxide concentrations and questionnaire surveyed aftrer sleeping. The concentration of Carbon Dioxide depending on ventilation rate in the chamber was analyzed for proper ventilation rate. The results of this paper can be summarized as follows. (1) When two persons experiment, 0.7 ventilation rate was in excess of 1000ppm. (2) When one person experiment, 0.7 and 0.4 ventilation rates were satisfied the criteria of IAQ. (3) It compared 0.4 with 0.7 in the ventilation rate, 0.4 ventilation rate could reduced about 80% of the power by fan similarity law.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.4
• /
• pp.751-756
• /
• 2018

In smart factories and industrial IoT, all facilities in a factory are monitored over the Internet, thereby facility can reduce the downtime and increase the availiability by preventive maintenance before it breaks down. The abnormal conditions of the major facilities in the plant are caused by abnormal temperature rise, vibration, and variations in noise. Consequently, it is critical to develop a very small smart device that is easily installed in a small space to enable real-time monitoring of the vibration status of the facility. In this study, smart devices were developed for smart factory fault prediction and robustness management using ultra small micro-controllers with WiFi capabilities and MEMS acceleration sensors.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.11
• /
• pp.729-736
• /
• 2000

This paper deals with the characteristic analysis of magnetizer for convergence purity magnet by the finite element method. The analysis utilizes combined method of the time-stepped finite element analysis and the Preisach model with hysteresis phenomena. In the finite element analysis, the non-linearity and the eddy current of the magnetizing fixure and permanent-magnet are taken account. The magnetization distribution in the permanent magnet is determined by using Preisach model which are composed of Everett function table and the first order transition curves is obtained by the Vibrating Sample Magnetometer. The calculated flux density values on the surface of the permanent magnet are led to the approximated gauss density values measured by the gauss meter. As a result, winding current, copper loss, eddy current loss of the magnetizing yoke, flux plot, surface gauss plot, temperature rise of the coil and resistor variation, vector diagram of magnetization distribution are shown.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.7-8
• /
• 2005

Silicon(Si) nanowires have been grown by thermal chemical vapor deposition using the 20h ball-milled SiO powders under controlled conditions without the catalyst. For the synthesis of Si nanowires, $Al_2O_3$ substrates were used. Current-Voltage(I-V) and photoresponses were measured for the single Si nanowire in vacuum at room temperature. The light sources for these measurements were the 325 nm wavelength line from a He-Cd laser and the 633 nm wavelength line from a He-Ne laser. The intensity of the photoresponse is independent of the illumination time. And rise and decay times of the photoresponses are shorter than 1 sec.

• Journal of Climate Change Research
• /
• v.5 no.3
• /
• pp.267-275
• /
• 2014

A key driver for climate change caused by global average temperature rise is greenhouse gas cumulative emissions that stay for long term in the atmosphere. Although at the moment there is no GHG emission, global warming will continue owing to GHG cumulative emission. In this study, scenarios are developed based on two types of optimistic and conservative diffusion goal. There were a total of 6 alternatives scenarios. The objective of this study are to compare scenarios in terms of GHG cumulative emissions and alternative fuels. An object of analysis is the residential buildings and time frame of scenarios is set up by 2030. And this study uses the LEAP model that is a bottom-up energy model. In conclusion, It is important to set specific diffusion pathway for mitigating climate change virtually.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.2
• /
• pp.160-164
• /
• 2022

In this paper, through the development of a smart panel (LCD kiosk) controller, contents to develop a system that can be operate in a desired environment by operating the window control and ventilation facilities according to the automatic controller operation based on the set values such as temperature, humidity, sunlight, and rainfall. In particular, the MQTT protocol-based sensor module can be directly manufactured and applied at any time based on various communication and power sources such as wireless, wired, and PLC (power line communication) to obtain the desired data, as well as fire, power failure, and intrusion in the house. It is also a system that enables operation and monitoring from a remote location based on the cloud environment by connecting sensors. Kiosks are currently being used in many places, and the demand for them is on the rise, and an active influx of young people can be expected through environmental improvement. It is expected to increase interest and understanding for improvement.

• Journal of Sensor Science and Technology
• /
• v.18 no.1
• /
• pp.54-62
• /
• 2009

${Co_3}{O_4}$ and ${Co_3}{O_4}$-based thick films with additives such as ${Co_3}{O_4}-{Fe_2}{O_3}$(5 wt.%), ${Co_3}{O_4}-{SnO_2}$ (5 wt.%), ${Co_3}{O_4}-{WO_3}$(5 wt.%) and ${Co_3}{O_4}$-ZnO(5 wt.%) were fabricated by screen printing method on alumina substrates. Their structural properties were examined by XRD and SEM. The sensitivities to iso-${C_4}H_{10}$, $CH_4$, CO, $NH_3$ and NO gases were investigated with the thick films heat treated at $400^{\circ}C$, $500^{\circ}C$ and $600^{\circ}C$. From the gas sensing properties of the films, the films showed p-type semiconductor behaviors. ${Co_3}{O_4}-{SnO_2}$(5 wt.%) thick film heat treated at $600^{\circ}C$ showed higher sensitivity to i-${C_4}H_{10}$ and CO gases than other thick-films. ${Co_3}{O_4}-{SnO_2}$(5 wt.%) thick film heat treated at $600^{\circ}C$ showed the sensitivity of 170 % to 3000 ppm iso-${C_4}H_{10}$ gas and 100 % to 100 ppm CO gas at the working temperature of $250^{\circ}C$. The response time to i-${C_4}H_{10}$ and CO gases showed rise time of about 10 seconds and fall time of about $3{\sim}4$ minutes. The selectivity to i-${C_4}H_{10}$ and CO gases was enhanced in the ${Co_3}{O_4}-{SnO_2}$(5 wt.%) thick film.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.28 no.5
• /
• pp.454-469
• /
• 2006

Today, there is considerable evidence to support a cause-effect relationship between microbial colonization and the pathogenesis of implant failures. The presence of bacteria on implant surfaces may result in an inflammation of the peri-implant mucosa, and, if left untreated, it may lead to a progressive destruction of alveolar bone supporting the implant, which has been named as peri-impantitis. Several maintenance regimens and treatment strategies for failing implants have been suggested. Recently, in addition to these conventional tools, the use of different laser systems has also been proposed for treatment of peri-implant infections. As lasers can perform excellent tissue ablation with high bactericidal and detoxification effects, they are expected to be one of the most promising new technical modalities for treatment of failing implants. It is introduced that Er,Cr:YSGG laser, operating at 2780nm, ablates tissue by a hydrokinetic process that prevents temperature rise. We studied the change of the titanium implant surface under scanning electron microscopy after using Er,Cr:YSGG laser at various energies, irradiation time. In this study, Er,Cr:YSGG laser irradiation of implant fixture showed different effects according to implant surface. Er,Cr:YSGG laser in TPS surface with RBM not alter the implant surface under power setting of 4 Watt(W) and irradiation time of 30sec. But in TPS surface with $Ca_3P$ coating alter above power setting of 2W and irradiation time of 10sec. TPS surface with RBM showed microfracture in 4W, 30sec and TPS surface with $Ca_3P$ coating showed destruction of fine crystalline structure, melting in excess of 2W, 10sec. We concluded that proper power setting, air, water of each implant surface must be investigated and implant surface must be irradiated under the damaged extent.

• Journal of Oral Medicine and Pain
• /
• v.30 no.3
• /
• pp.375-381
• /
• 2005

Er:YAG laser has been considered a promising alternative to dental drill and many researches indicate that adjustment to variable parameters, including water flow rate, pulse energy and pulse repetition rate, can be made to improve ablation ability and efficiency of the laser. Of these parameters, addition of water spray during irradiation has been thought to ablate dental hard tissue more rapidly and safely. The purpose of this study was to investigate tooth ablation amount by Er:YAG laser irradiation as related to varied water flow rates added and, ultimately to find the most effective water flow rate for ablation. In addition, the temperature change of pulp chamber during irradiation was also monitored on the irradiated and opposite pulpal walls, respectively. An Er:YAG laser with contact mode was employed. Extracted human molars were split into two pieces for ablation experiment. Pulse energies of 200 and 300 mJ with a pulse repetition rate of 20 Hz and 5 water flow rates (1.6, 3.0, 5.0, 7.0, and 10.0 ml/min) were applied. Each irradiation was performed for 3 seconds. According to these parameters, experimental groups were divided into 10 subgroups which consisted of 5 specimens. For temperature experiment, another 5 tooth-specimens were prepared in the manner that pulp chamber was open through access cavity preparation and two temperature-measuring probes were placed respectively on the irradiated and the opposite walls of pulp chamber. From the experiment on ablation amount related to different water flow rates, it was shown that the least water flow rate of 1.6 ml/min ablated more than any other water flow rates (p<0.000). When the irradiation for 3 seconds, combined with the pulse repetition time of 20Hz and the water flow rate of 1.6 ml/min was done to tooth specimen, the temperature rise was not noticeable both on the irradiated and the opposite pulpal walls (less than 3$^{\circ}C$) and there was no significant difference in temperature rise between the two pulse energies, 200 and 300 mJ. From the results of this study, it is suggested that tooth ablation with Er:YAG laser can be done effectively and safely at a energy between 200 and 300 mJ/pulse and a pulse repetition rate of 20 Hz when the lasing is conjugated with the water flow rate of 1.6ml/min.

• The Korean Journal of Pain
• /
• v.14 no.2
• /
• pp.181-185
• /
• 2001

Background: Bradycardia frequently occurs in intravenous anesthesia with propofol. Additionally, the thoracic sympathetic nerves influence the heart so that the heart rate (HR) and blood pressure are expected to decrease due to this procedure. Therefore, we measured changes in HR, mean arterial pressure (MAP) and both thumb temperatures before and after thoracic sympathicotomy under total intravenous anesthesia with propofol. Methods: The subjects included 21 outpatients of ASA class I who received thoracoscopic thoracic sympathicotomy under total intravenous anesthesia. Anesthesia was induced with propofol (2 mg/kg) and vecuronium (0.1 mg/kg) and maintained with propofol-fentanyl-oxygen (100%). The surgical procedure was performed at the T3 level in the order of left sympathicotomy (LST) and right sympathicotomy (RST). Measurements of HR, MAP and both thumb temperatures were taken before induction of anesthesia, before and after LST and RST, and 1 hour after the completion of anesthesia. Additionally, the time to the beginning of a rise in temperature in both thumbs after sympathicotomy was recorded. Results: HR did not show any significant difference before or after sympathicotomy, however it decreased at 1 hour after the completion of anesthesia. MAP decreased after LST and decreased further after RST. Left thumb temperature began to increase at $45.8{\pm}10.7$ seconds after LST. Right thumb temperature initially decreased after LST and increased from $45.2{\pm}11.8$ seconds after RST. Subsequently, both increased temperatures were maintained at 1 hour after the completion of anesthesia. Conclusions: Although HR and MAP decreased, there were no severe hemodynamic changes. An increase in the thumb temperature was confirmed within 1 minute after sympathicotomy on the same side.