• Applied Chemistry for Engineering
• /
• v.4 no.4
• /
• pp.739-745
• /
• 1993

The characteristics of mass transfer in an inorganic ion exchange system where Cs and/or Sr are separated by means of zeolites was investigated. Experimental work to separate Cs or Sr was carried out for Cs-AW300 and CS-AW500 systems in case of Cs whereas for Sr-4A and Sr-13X systems in case of Sr. The experimental conditions were chosen as follows in the batch type separation : temperature $25^{\circ}C$, agitation speed 300rpm, amount of zeolite 4g, volume of solution $0.5{\ell}$, and concentrations of solution 1000ppm, 2000ppm, respectively. As a result, it was found that the mass transfer rate is controlled mainly by the liquid film diffusion. The mass transfer coefficients in the film were found to be in the range of $10^{-4}{\sim}10^{-3}cm/sec$, while the apparent diffusivity inside the particles was found to be in the order of $10^{-8}cm^2/sec$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.1
• /
• pp.143-150
• /
• 1997

The electrical properties of polysilicon thin films implanted with $B_2H_6$ diluted in $H_2$ as dopant source using ion mass doping technique and the effect of radiation damage on the dopant activation behavior were investigated. Comparing the SIMS profiles of boron in polysilicon films with that obtained from computer simulation using TRIM92 the most probable ion species were $B_2H_x\;^+$(x＝1, 2, 3‥‥) type molecular ions. As a result of the Implantation of energetic massive ions, a continuous amorphized layer was created in polysilicon films where the fraction of amorphized layer varied with doping time. This amorphization comes from the fact that mass separation of implanting species is not employed in this ion mass doping technique. In the dopant activation behavior, reverse annealing phenomenon appeared in the intermediate annealing temperature range for a severely damaged specimen. The experimental result showed that the off-state current of the p-channel polysilicon thin film transistor is dependent on the degree of radiation damage.

• Applied Biological Chemistry
• /
• v.24 no.4
• /
• pp.213-217
• /
• 1981

A Kimchi pasteurizer consisting of preheating, holding, cooling and liquid separation sections was built with copper tubing coil and glasses. The liquid portion of a Chiness Cabbage Kimchi prepared with 3% NaCl solution was preheated and held for 3 minutes at sterilization temperature. Thereafter it was cooled momentarily and recombined with the untreated solid part of Kimchi At four different temperatures of $68^{\circ}$, $75^{\circ}$, $81^{\circ}$ and $85^{\circ}C$ Kimchi was sterilized and examined for the sterilization effects by measuring acid and pH changes of the Kimchi when stored at $15^{\circ}C$. The shelf-life of sterilized Kimchi was prolonged by two folds compared with the untreated one. When Kimchi was sterilized at different maturing stages. the less cured one prolonged its shelf-life more effectively.

• Journal of Conservation Science
• /
• v.22
• /
• pp.77-86
• /
• 2008

The pre-treatment for conservation must be needed for the exhumed historic sites. So, the study of conservation and restoration of historical sites has progressed favorably with using various polymers for solving upper problems. The problems which should be essentially solved for conservation of the exhumed historic sites are, however, using reinforcing agents that don't impair their original forms and sorting reinforcing agents on the lines of the historic sites' soil. These agents should be able to use without the effect of outer environments like marsh, winter time or temperature. In this work, we synthesized Epoxy resin and Epoxy hardener for the restoration of historical sites. These products have very good tension strength and adhesion strength and various physical properties that the users want. Particularly, these epoxy with high viscosity have good separation of between Epoxy final product and Urethane pre-surface.

• Korean Journal of Medicinal Crop Science
• /
• v.15 no.3
• /
• pp.215-219
• /
• 2007

This study was conducted to analyze not only for the quality guaranteed of red ginseng but also for the minor ginsenosides. Although several studies have reported to analyze ginseng saponins, those were focused to major saponins, including 6 to 7 ginsenosides. As increase of interest in medicinal effect of ginseng products, anasis of various ginsenosides in both red and white ginseng are strongly demanded. To perform optital condition of 12 ginsenoside analysis, We controlled HPLC conditions, such as the gradient elution of the mobile phase. We found the adequate separation method for 12 ginse-nosides. The optimum condition was as following : H$_2$O/CH$_3$CN ratios were 82/18, 70/30, 55/45 and 50/50, respectively. Sol-vent flow rate was 1.00 ma/min. Column temperature was kept to 35$^{\circ}$C. UV detector was set to 203 nm.

• Journal of computational fluids engineering
• /
• v.21 no.4
• /
• pp.11-18
• /
• 2016

A numerical study is conducted on the optical fiber coating flow in a primary coating nozzle consisting of three major parts: a resin chamber, a contraction and a coating die of small diameter. The flow is driven by the optical fiber penetrating the center of the nozzle at a high speed. The axisymmetric two-dimensional flow and heat transfer induced by viscous heating are examined based on the laminar flow assumption. Numerical experiments are performed with varying the convergent angle of nozzle contraction and the optical fiber drawing speed. The numerical results show that for high drawing speed greater than 30 m/s, there is a transition in the essential flow features depending on the convergent angle. For a large convergent angle greater than $30^{\circ}$, unfavorable multicellular flow structures are monitored, which could be associated with wall boundary-layer separation. In the regime of small convergent angle, as the angle increases, the highest resin temperature at the exit of die and the coating thickness decrease but the sensitivity of coating thickness on drawing speed and the maximum shear strain of resin on the optical fiber increase. The effects of the convergent angle are discussed in view of compromise searching for an appropriate angle for high-speed optical fiber coating.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.133-138
• /
• 2013

Acrylonitrile-butadiene-styrene (ABS) plastic is a polymer material extensively used in electrical and electronic applications. Nickel (Ni) thin film was deposited on ABS by electroless plating, after its surface was treated and modified with atmospheric plasma generated by means of dielectric barrier discharges (DBDs) in air. The method in this study was developed as a pre-treatment for electroless plating using DBDs, and is a dry process featuring fewer processing steps and more environmentally friendliness than the chemical method. After ABS surfaces were modified, surface morphologies were observed using a scanning electron microscope (SEM) to check for any physical changes of the surfaces. Cross-sectional SEM images were taken to observe the binding characteristics between metallic films and ABS after metal plating. According to the SEM images, the depths of ABS by plasma are shallow compared to those modified by chemically treatment. The static contact angles were measured with deionized (DI) water droplets on the modified surfaces in order to observe for any changes in chemical activities and wettability. The surfaces modified by plasma showed smaller contact angles, and their modified states lasted longer than those modified by chemical etching. Adhesion strengths were measured using 3M tape (3M 810D standard) and by 90° peel-off tests. The peel-off test revealed the stronger adhesion of the Ni films on the plasma-modified surfaces than on the chemically modified surfaces. Thermal shock test was performed by changing the temperature drastically to see if any detachment of Ni film from ABS would occur due to the differences in thermal expansion coefficients between them. Only for the plasma-treated samples showed no separation of the Ni films from the ABS surfaces in tests. The adhesion strengths of metallic films on the ABS processed by the method developed in this study are better than those of the chemically processed films.

• Biomolecules & Therapeutics
• /
• v.15 no.2
• /
• pp.123-126
• /
• 2007

A sensitive, simple and highly selective liquid chromatography method of determination for extraction of pseudoephedrine hydrochloride from Allegra D tablet was developed. The chief benefit of the present method is the minimal sample preparation, as the procedure is only filtering through pore syringe filter. Two drugs (pseudoephedrine hydrochloride, fexofenadine) were separated on a C$_{18}$ column and analyzed by high performance liquid chromatography (HPLC). The method had a chromatographic run time of 8.0 min. 1 ml of pseudoephedrine hydrochloride solution (1 mg/ml) was filtered through 0.22 um pore syringe filter. 50 ul of filtering solution was injected to HPLC pump and we knew the retention time (1.85 min) of separating of pseudoephedrine hydrochloride using UV detector at 280 nm. We used C$_{18}$ column (4.6 mm${\times}$250 mm), mobile phase solution (<0.05 mol/L NaH$_2$PO$_4$, 2 ml/L H$_3$PO$_4$>/CH$_3$CN / sodium dodesyl sulfate = 60 ml / 40 ml / 1 g). We separated psedoephedrine hydrochloride at run time of 1.85 min from Allegra D tablet solution (1 mg/ml) filtered through 0.22 um pore syringe filter using UV detector at 280 nm. Flow rate was set at 1.0 ml/min and the column temperature was set at 40$^{\circ}C$. Psedoephedrine hydrochloride solution (1 mg/ml) separated from Allegra D tablet was filtered through 0.22 um pore syringe filter and injected 50 ul. We confirmed the peak of psedoephedrine hydrochloride at same retention time and the separating solution was freeze-dried. In conclusion, A simple isocratic reverse-phase HPLC method has been developed that provides excellent separation of pseudoephedrine from Allegra D tablet.

• Journal of Dairy Science and Biotechnology
• /
• v.24 no.1
• /
• pp.53-63
• /
• 2006

Nano and micro capsulation (NM capsulation) involve the incorporation for nanofood materials, enzymes, cells or other materials in small capsules. Since Kim D. M. (2001) showed that a new type of food called firstly the name of nanofood, which means nanotechnology for food, and the encapsulated materials can be protected from moisture, heat or other extreme conditions, thus enhancing their stability and maintaining viability applications for this nanofood technique have increased in the food. NM capsules for nanofood is also utilized to mask odours or tastes. Various techniques are employed to form the capsules, including spray drying, spray chilling or spray cooling, extrusion coating, fluidized bed coating, liposome entrapment, coacervation, inclusion complexation, centrifugal extrusion and rotational suspension separation. Each of these techniques is discussed in this review. A wide variety of nanofood is NM capsulated - flavouring agents, acids, bases, artificial sweeteners, colourants, preservatives, leavening agents, antioxidants, agents with undesirable flavours, odours and nutrients, among others. The use of NM capsulation for sweeteners such as aspartame and flavors in chewing gum is well known. Fats, starches, dextrins, alginates, protein and lipid materials can be employed as encapsulating materials. Various methods exist to release the ingredients from the capsules. Release can be site-specific, stage-specific or signaled by changes in pH, temperature, irradiation or osmotic shock. NM capsulation for the nanofood, the most common method is by solvent-activated release. The addition of water to dry beverages or cake mixes is an example. Liposomes have been applied in cheese-making, and its use in the preparation of nanofood emulsions such as spreads, margarine and mayonnaise is a developing area. Most recent developments include the NM capsulation for nanofood in the areas of controlled release, carrier materials, preparation methods and sweetener immobilization. New markets are being developed and current research is underway to reduce the high production costs and lack of food-grade materials.

• Applied Chemistry for Engineering
• /
• v.16 no.3
• /
• pp.427-433
• /
• 2005

The use of the microwave-assisted process for the extraction of effective constituents from ginseng was investigated at various operating conditions. The influence of solvent (ethanol-water, 50% v/v) to ginseng ratio, particle size and applied microwave power on the efficiency of extraction was examined. The microwave extraction system used was custom manufactured so that the intensity of microwave may be varied by using anode-voltage controller. It was found that the ratio of 6 : 1 (vol/mass) gave a good extraction efficiency. Small particle size gave high yield but it caused difficulties in the separation of solvent from the sludge. The higher power was no guarantee of the efficient extraction yield. The more important factor than the employed power was the adequate temperature under sufficient contact time. Using deionized-water as swelling agent, the degree of swelling of ginseng by microwave heating and conventional heating in water-bath was also studied. It was observed that the microwave heating enhanced the swelling much more than the conventional heating. It is believed that this enhanced swelling was responsible for the rapid microwave-assisted extraction rate.